Home محصولات ماژول OLED ماژول های OLED Touch WEN025664B-CTP

مدل شماره WEN025664B-CTP

◄نوع : گرافیک
◄ساختار: COF+FR+PCB
◄سایز: 3.12 اینچ
◄ماتریس نقطه ای 256×64
◄کنترلگر SSD1322
◄منبع انرژی +3V
◄چرخه کار 1/64
◄رابط: 6800, 8080 ,SPI
◄صفحه لمسی: با پنل (صفحه) لمسی خازنی (CTP)
◄Detect Point : 1 Finger
◄رنگ صفحه‌نمایش: سفید / زرد / آبی آسمانی / سبز
◄Support Grayscale

طراحی

3.12 inch 256x64 COF Touch OLED Display with PCB +Frame - WEN025664B-CTP
 

Data source ref: WEN025664BWPP3D00000

مشخصات

عملکرد پین رابط

Pin Number نماد I/O عملکرد
1 VSS P Ground.
2 VDD P Power Supply for Core Logic Circuit
Power supply pin for core logic operation. A capacitor is required to connect between this pin and VSS
3 N.C. P Reserved Pin
The N.C. pin between function pins are reserved for compatible and flexible design.
4 D/C# I Data/Command Control
This pin is Data/Command control pin connecting to the MCU.
When the pin is pulled HIGH, the content at D[7:0] will be interpreted as data.
When the pin is pulled LOW, the content at D[7:0] will be interpreted as command.
5 R/W#
(WR#)
I Read/Write Select or Write
This pin is MCU interface input. When interfacing to a 68XX-series microprocessor, this pin will be used as Read/Write (R/W#) selection input. Pull this pin to “High” for read mode and pull it to “Low” for write mode.
When 80XX interface mode is selected, this pin will be the Write (WR#) input. Data write operation is initiated when this pin is pulled low and the CS# is pulled low.
When serial mode is selected, this pin must be connected to VSS.
6 E/RD# I Read/Write Enable or Read
This pin is MCU interface input.
When interfacing to a 68XX-series microprocessor, this pin will be used as the Enable (E) signal. Read/write operation is initiated when this pin is pulled high and the CS# is pulled low.
When connecting to an 80XX-microprocessor, this pin receives the Read (RD#) signal. Data read operation is initiated when this pin is pulled low and CS# is pulled low.
When serial mode is selected, this pin must be connected to VSS.
7~14 DB0 I/O Host Data Input/Output Bus
These pins are 8-bit bi-directional data bus to be connected to the microprocessor’s data bus.
When serial mode is selected, D1 will be the serial data input SDIN and D0 will be the serial clock input SCLK.
DB1
DB2
DB3
DB4
DB5
DB6
DB7
15 NC P Reserved Pin
The N.C. pin between function pins are reserved for compatible and flexible design.
16 RES# I This pin is reset signal input.
When the pin is pulled LOW, initialization of the chip is executed.
Keep this pin pull HIGH during normal operation.
17 CS# I Data/Command Control
This pin is the chip select input connecting to the MCU. The chip is enabled for MCU communication only when CS# is pulled LOW.
18 NC P Reserved Pin
The N.C. pin between function pins are reserved for compatible and flexible design.
19 BS1 I Communicating Protocol Select
These pins are MCU interface selection input. See the following table:
BS[1:0] Bus Interface electioin
00 4 line SPI
01 3 line SPI
10 8-bit 8080 parallel
11 8-bit 6800 parallel
Note
(1) 0 is connected to VSS
(2) 1 is connected to VDD
20 BS0
21 TP_SCK I I2C clock input
22 TP_SDA I I2C data input and output
23 TP_INT I External interrupt to the host
24 TP_RST I External Reset, Low is active

داده مکانیکی

مورد ابعاد واحد
ماتریس نقطه ای 256 × 64 Dots
ابعاد ماژول 89.2 × 44.0 × 7.98 mm
ناحیه فعال 76.78 × 19.18 mm
اندازه نقطه 0.278 × 0.278 mm
درجه نقطه 0.3 × 0.3 mm
حالت رنگ ماتریس غیرفعال
رنگ صفحه‌نمایش Monochrome
Drive Duty 1/64 Duty
Gray Scale 4 bits
OLED IC SSD1322 (COF)
OLED رابط 6800, 8080, SPI
سایز 3.12 اینچ
CTP IC FT6336U
Detect Point 1
CTP رابط I2C
سطح تابش خیره‌کننده

بیشینه مقادیر مجاز مطلق

Parameter نماد مقدار حداقل مقدار حداکثر واحد
Supply Voltage for Display VDD -0.3 4 V
دمای عملیاتی TOP -20 +70 °C
دمای بسته‌بندی TSTG -30 +80 °C

مشخصات الکترونیکی

DC مشخصات الکترونیکی

مورد نماد وضعیت مقدار حداقل مقدار معمول مقدار حداکثر واحد
Supply Voltage for Logic VDD 2.8 3.0 3.3 V
High Level Input VIH 0.8×VDD VDD V
Low Level Input VIL 0 0.2×VDD V
High Level Output VOH 0.9×VDD VDD V
Low Level Output VOL 0 0.1×VDD V
50% Check Board operating Current IDD VDD =3V 150 300 mA
go top
close