Ana sayfa Ürünler OLED Ekran Dokunmatik Ekran OLED WEN025664B-CTP

3.12 inç 256x64 COF OLED Ekran dokunmatik panelle birlikte +PCB +Delikli Çerçeve

Model No. WEN025664B-CTP

►Türü : Grafik
►Yapı : COF+FR+PCB
►Boyut : 3.12 inç
►256×64 dot matrisi
►Kontrolör dahil SSD1322
►3V güç sağlayıcı
►1/64 görev döngüsü
►Ara yüz :6800, 8080, SPI
►Dokunmatik Ekran: Kapasitif dokunmatik panelle birlikte (CTP)
►Dokunma Noktaları : 1 Parmak
►OLED Rengi: Beyaz / Sarı / Gök Mavisi / Yeşil
►Gri Tonlama Desteği

ÇIZIM

3.12 inch 256x64 COF Touch OLED Display with PCB +Frame - WEN025664B-CTP
 

Data source ref: WEN025664BWPP3D00000

AYRINTILAR

Arayüz Pin Fonksiyonlari

Pin Number Sembol I/O Fonksiyon
1 VSS P Ground.
2 VDD P Power Supply for Core Logic Circuit
Power supply pin for core logic operation. A capacitor is required to connect between this pin and VSS
3 N.C. P Reserved Pin
The N.C. pin between function pins are reserved for compatible and flexible design.
4 D/C# I Data/Command Control
This pin is Data/Command control pin connecting to the MCU.
When the pin is pulled HIGH, the content at D[7:0] will be interpreted as data.
When the pin is pulled LOW, the content at D[7:0] will be interpreted as command.
5 R/W#
(WR#)
I Read/Write Select or Write
This pin is MCU interface input. When interfacing to a 68XX-series microprocessor, this pin will be used as Read/Write (R/W#) selection input. Pull this pin to “High” for read mode and pull it to “Low” for write mode.
When 80XX interface mode is selected, this pin will be the Write (WR#) input. Data write operation is initiated when this pin is pulled low and the CS# is pulled low.
When serial mode is selected, this pin must be connected to VSS.
6 E/RD# I Read/Write Enable or Read
This pin is MCU interface input.
When interfacing to a 68XX-series microprocessor, this pin will be used as the Enable (E) signal. Read/write operation is initiated when this pin is pulled high and the CS# is pulled low.
When connecting to an 80XX-microprocessor, this pin receives the Read (RD#) signal. Data read operation is initiated when this pin is pulled low and CS# is pulled low.
When serial mode is selected, this pin must be connected to VSS.
7~14 DB0 I/O Host Data Input/Output Bus
These pins are 8-bit bi-directional data bus to be connected to the microprocessor’s data bus.
When serial mode is selected, D1 will be the serial data input SDIN and D0 will be the serial clock input SCLK.
DB1
DB2
DB3
DB4
DB5
DB6
DB7
15 NC P Reserved Pin
The N.C. pin between function pins are reserved for compatible and flexible design.
16 RES# I This pin is reset signal input.
When the pin is pulled LOW, initialization of the chip is executed.
Keep this pin pull HIGH during normal operation.
17 CS# I Data/Command Control
This pin is the chip select input connecting to the MCU. The chip is enabled for MCU communication only when CS# is pulled LOW.
18 NC P Reserved Pin
The N.C. pin between function pins are reserved for compatible and flexible design.
19 BS1 I Communicating Protocol Select
These pins are MCU interface selection input. See the following table:
BS[1:0] Bus Interface electioin
00 4 line SPI
01 3 line SPI
10 8-bit 8080 parallel
11 8-bit 6800 parallel
Note
(1) 0 is connected to VSS
(2) 1 is connected to VDD
20 BS0
21 TP_SCK I I2C clock input
22 TP_SDA I I2C data input and output
23 TP_INT I External interrupt to the host
24 TP_RST I External Reset, Low is active

Mekanik Veri

Kalem Ölçü Birim
Nokta Matrisi 256 x 64 Dots
Modül ölçüleri 89.2 × 44.0 × 7.98 mm
Aktif alan 76.78 × 19.18 mm
Nokta boyutu 0.278 × 0.278 mm
Nokta sıklığı 0.3 × 0.3 mm
Display Mode Pasif Matrisli
Display Color Monokrom
Drive Duty 1/64 Duty
Gri Tonlama 4 bits
OLED IC SSD1322 (COF)
OLED Arayüz 6800, 8080, SPI
Boyut (Köşegen) 3.12 inç
CTP IC FT6336U
Dokunma Noktaları 1
CTP Arayüz I2C
Yüzey Parlama

Maksimum Değerler

Parameter Sembol Minumum Deger Maksimum Deger Birim
Supply Voltage for Display VDD -0.3 4 V
Çalışma Sıcaklığı TOP -20 +70 °C
Saklama Sıcaklığı TSTG -30 +80 °C

Elektronik Özellikleri

DC Elektronik Özellikleri

Kalem Sembol Durum Minumum Deger Tipik Deger Maksimum Deger Birim
Supply Voltage for Logic VDD 2.8 3.0 3.3 V
High Level Input VIH 0.8×VDD VDD V
Low Level Input VIL 0 0.2×VDD V
High Level Output VOH 0.9×VDD VDD V
Low Level Output VOL 0 0.1×VDD V
50% Check Board operating Current IDD VDD =3V 150 300 mA
 

Search keyword: 256x64 oled, oled 256x64, 3.12 oled, 3.12" oled, 3.12 inç oled, oled 3.12"

go top
close