0,69 inç Grafik 96x16 COG OLED Ekran
Model No. WEO009616B
►Türü: Grafik
►Yapı : COG
►Boyut : 0,69 inç
►96 x 16 dot matrisi
►IC:SSD1306
►3V güç sağlayıcı
►1/16 görev
►Ara yüz : I2C
►OLED Rengi: Beyaz / Sarı
Açıklama
WEO009616B, 96x16 piksel çözünürlükten üretilmiş 0,69 inç COG OLED ekran modülüdür. WEO009616B 0,69 inç OLED ekran, SSD1306 denetleyici IC’de yerleşiktir; I2C arayüzünü, 3V güç kaynağını destekler. Bu modül serisi -30 ℃ ile +70 ℃ arasındaki sıcaklıklarda çalışabilir; saklama sıcaklıkları -30 ℃ ile +70 ℃ arasında değişir.
Bu modül, ultra ince, hafif ve düşük güç tüketimli, küçük boyutlu bir COG OLED ekrandır. Akıllı ev uygulamaları, tıbbi cihazlar, taşınabilir cihazlar, giyilebilir cihazlar için çok uygundur.
ÇIZIM
AYRINTILAR
Arayüz Pin Fonksiyonlari
No. | Sembol | TANIM |
---|---|---|
1 | C2N | C1P/C1N – Pin for charge pump capacitor; Connect to each other with a capacitor. C2P/C2N – Pin for charge pump capacitor; Connect to each other with a capacitor. |
2 | C2P | |
3 | C1P | |
4 | C1N | |
5 | VBAT | This is the power supply pin for the internal buffer of the DC/DC voltage converter. It must be connected to external source when the converter is used. It should be connected to VDD when the converter is not used. |
6 | NC | No connection |
7 | VSS | This is a ground pin. |
8 | VDD | Power supply pin for core logic operation. |
9 | RES# | This pin is reset signal input. When the pin is low, initialization of the chip is executed. Keep this pin HIGH (i.e. connect to VDD) during normal operation. |
10 | SCL | When I2C mode is selected, D2, D1 should be tied together and serve as SDAout, SDAin in application and D0 is the serial clock input, SCL. |
11 | SDA | |
12 | IREF | This pin is segment current reference pin. A resistor should be connected between this pin and VSS. Set the current lower than 30uA. When internal IREF is used, this pin should be kept NC. |
13 | VCOMH | The pin for COM signal deselected voltage level. A capacitor should be connected between this pin and VSS. |
14 | VCC | This is the most positive voltage supply pin of the chip. A stabilization capacitor should be connected between this pin and VSS when the converter is used. It must be connected to external source when the converter is not used. |
Mekanik Veri
Kalem | Ölçü | Birim |
---|---|---|
Nokta Matrisi | 96 × 16 Dots | - |
Modül ölçüleri | 26.3 × 8.0 × 1.26 | mm |
Aktif alan | 17.26 × 3.18 | mm |
Nokta boyutu | 0.16 × 0.18 | mm |
Nokta sıklığı | 0.18 × 0.20 | mm |
Display Mode | Pasif Matrisli | |
Display Color | Monokrom | |
Drive Duty | 1/16 Duty | |
IC | SSD1306 | |
Arayüz | I2C | |
Boyut (Köşegen) | 0.69 inç |
Maksimum Değerler
Parameter | Sembol | Minumum Deger | Maksimum Deger | Birim |
---|---|---|---|---|
Supply Voltage for Logic | VDD | 0 | 4 | V |
Supply Voltage for Display | VCC | 0 | 16 | V |
Charge Pump Regulator Supply Voltage |
VBAT | 0 | 5 | V |
Çalışma Sıcaklığı | TOP | -30 | 70 | °C |
Saklama Sıcaklığı | TSTG | -30 | 70 | °C |
Elektronik Özellikleri
DC Elektronik Özellikleri
Kalem | Sembol | Durum | Minumum Deger | Tipik Deger | Maksimum Deger | Birim |
---|---|---|---|---|---|---|
Supply Voltage for Logic | VDD | - | 1.65 | 3.0 | 3.3 | V |
Supply Voltage for Display (Supplied Externally) |
VCC | - | 6.0 | 7.5 | 8.0 | V |
Charge Pump Regulator Supply Voltage | VBAT | - | 3.0 | - | 4.2 | V |
Charge Pump Output Voltage for Display (Generated by Internal DC/DC) | Charge Pump VCC |
- | 7.0 | 7.5 | - | V |
Input High Volt. | VIH | - | 0.8×VDD | - | VDD | V |
Input Low Volt. | VIL | - | 0 | - | 0.2×VDD | V |
Output High Volt. | VOH | - | 0.9×VDD | - | VDD | V |
Output Low Volt. | VOL | - | 0 | - | 0.1×VDD | V |
50% check Board operating Current (VCC Supplied Externally) | ICC | - | - | 5 | 10 | mA |
50% check Board operating Current (VCC Generated by Internal DC/DC) | IBAT | - | 5 | 10 | mA |
Search keyword: 96x16 oled, oled 96x16, 0.69 oled, 0.69" oled, 0.69 inç oled, oled 0.69 inç