Accueil Produits Module OLED Modules afficheurs OLED Avec dalle tactile WEN025664B-CTP

N° de modèle WEN025664B-CTP

►Type: Graphique
►Structure: COF+FR+PCB
►Dimension: 3.12 pouces
►Matrice de points 256×64
►Contrôleur intégré SSD1322
►Alimentation 3V
►Taux de rafraichissement 1/64 duty cycle
►Interface: 6800, 8080, SPI
►Dalle tactile: avec dalle tactile capacitive (CTP)
►Detect Point : 1 Finger
►Couleur d'affichage: Blanc / Jaune / Bleu ciel / Vert
►Support Grayscale

DESSIN

3.12 inch 256x64 COF Touch OLED Display with PCB +Frame - WEN025664B-CTP
 

Data source ref: WEN025664BWPP3D00000

SPÉCIFICATIONS

Fonction PIN sur l'interface

Pin Number Symbole I/O Description
1 VSS P Ground.
2 VDD P Power Supply for Core Logic Circuit
Power supply pin for core logic operation. A capacitor is required to connect between this pin and VSS
3 N.C. P Reserved Pin
The N.C. pin between function pins are reserved for compatible and flexible design.
4 D/C# I Data/Command Control
This pin is Data/Command control pin connecting to the MCU.
When the pin is pulled HIGH, the content at D[7:0] will be interpreted as data.
When the pin is pulled LOW, the content at D[7:0] will be interpreted as command.
5 R/W#
(WR#)
I Read/Write Select or Write
This pin is MCU interface input. When interfacing to a 68XX-series microprocessor, this pin will be used as Read/Write (R/W#) selection input. Pull this pin to “High” for read mode and pull it to “Low” for write mode.
When 80XX interface mode is selected, this pin will be the Write (WR#) input. Data write operation is initiated when this pin is pulled low and the CS# is pulled low.
When serial mode is selected, this pin must be connected to VSS.
6 E/RD# I Read/Write Enable or Read
This pin is MCU interface input.
When interfacing to a 68XX-series microprocessor, this pin will be used as the Enable (E) signal. Read/write operation is initiated when this pin is pulled high and the CS# is pulled low.
When connecting to an 80XX-microprocessor, this pin receives the Read (RD#) signal. Data read operation is initiated when this pin is pulled low and CS# is pulled low.
When serial mode is selected, this pin must be connected to VSS.
7~14 DB0 I/O Host Data Input/Output Bus
These pins are 8-bit bi-directional data bus to be connected to the microprocessor’s data bus.
When serial mode is selected, D1 will be the serial data input SDIN and D0 will be the serial clock input SCLK.
DB1
DB2
DB3
DB4
DB5
DB6
DB7
15 NC P Reserved Pin
The N.C. pin between function pins are reserved for compatible and flexible design.
16 RES# I This pin is reset signal input.
When the pin is pulled LOW, initialization of the chip is executed.
Keep this pin pull HIGH during normal operation.
17 CS# I Data/Command Control
This pin is the chip select input connecting to the MCU. The chip is enabled for MCU communication only when CS# is pulled LOW.
18 NC P Reserved Pin
The N.C. pin between function pins are reserved for compatible and flexible design.
19 BS1 I Communicating Protocol Select
These pins are MCU interface selection input. See the following table:
BS[1:0] Bus Interface electioin
00 4 line SPI
01 3 line SPI
10 8-bit 8080 parallel
11 8-bit 6800 parallel
Note
(1) 0 is connected to VSS
(2) 1 is connected to VDD
20 BS0
21 TP_SCK I I2C clock input
22 TP_SDA I I2C data input and output
23 TP_INT I External interrupt to the host
24 TP_RST I External Reset, Low is active

Données mécaniques

Article Dimensions Unité
Matrice de points 256 x 64 Dots
Dimensions du module 89.2 × 44.0 × 7.98 mm
Zone active 76.78 × 19.18 mm
Taille des points 0.278 × 0.278 mm
Pas des points 0.3 × 0.3 mm
Mode d'affichage Matrice passive
Couleur d'affichage Monochrome
Drive Duty 1/64 Duty
Gray Scale 4 bits
OLED IC SSD1322 (COF)
OLED Interface 6800, 8080, SPI
Diagonale 3.12 pouces
CTP IC FT6336U
Detect Point 1
CTP Interface I2C
Surface Reflets

Valeurs nominales maximales absolues

Parameter Symbole Valeur min Valeur max Unité
Supply Voltage for Display VDD -0.3 4 V
Température de fonctionnement TOP -20 +70 °C
Température de stockage TSTG -30 +80 °C

Caractéristiques électroniques

DC Caractéristiques électroniques

Article Symbole État Valeur min Valeur type Valeur max Unité
Supply Voltage for Logic VDD 2.8 3.0 3.3 V
High Level Input VIH 0.8×VDD VDD V
Low Level Input VIL 0 0.2×VDD V
High Level Output VOH 0.9×VDD VDD V
Low Level Output VOL 0 0.1×VDD V
50% Check Board operating Current IDD VDD =3V 150 300 mA

Search keyword: 256x64 oled, oled 256x64, 3.12 oled, 3.12" oled, 3.12 pouces oled, oled 3.12"

go top
close