3.12인치 OLED 디스플레이 모듈 터치패널이 있는
Артикул. WEX025664B-CTP
►Тип: Графический
►Тип монтажа контроллера: COF
►Диагональ: 3.12 дюйма
►Разрешение: 256×64 точек
►IC:SSD1322
►3V power supply
►1/64 duty cycle
►Интерфейс: 6800, 8080, SPI
►Емкостная сенсорная панель(CTP)
►1 точка касания
►Цвет дисплея: Белый / Желтый / Небесно голубой / Зеленый
►Инверсия
Описание
WEX025664B-CTP – это 3.12" дюймовый графический OLED дисплей с емкостной сенсорной тач панелью. Разрешение данного индикатора составляет 256x64 точки и сделан на базе контроллера IC SSD1322 c поддержкой интерфейсов: параллельного 6800/8080 8-Бит, I2C и четырехжильного SPI интерфейса. Напряжение питания для логики дисплея варьируется от 2.8V до 3.3V (типичное значение 3V), а напряжение питания для дисплея 14.5V, рабочий цикл 1/64. Встроенный контроллер IC емкостной сенсорной панели –FT6336U с поддержкой I2C интерфейса. На выбор доступна версия с монтажной рамкой.
OLED дисплей WEX025664B-CTP с емкостной сенсорной панелью идеально подходит для применения в таких областях как: “умный дом”, POS системы, Облачных/IoT системах, умных устройствах, автомобилестроении, коммуникационных системах, медицинских устройствах и т.д.
Данный дисплей может работать при температурах от -20 ° С до + 70 ℃; а температура хранения - от -30 ℃ до + 80 ℃.
Кроме того, линейка продукции с теми же OLED-панелями предлагает различные альтернативы:- Серия WEX025664B без металлической рамы и печатной платы.
- Серия WEN025664B с металлической рамой и печатной платой.
- Серия WEN025664B-CTP с металлической рамой, печатной платой и сенсорным экраном CTP.
Чертеж
Data source ref: WEX025664BWPP3D00000
Технические характеристики
Функции контроллера контактного интерфейса
No. | Символы | Описание | ||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|
1 | N.C. | Reserved Pin The N.C. pin between function pins are reserved for compatible and flexible design. |
||||||||||
2 | VSS | Ground. | ||||||||||
3 | VCC | Power supply for panel driving voltage. This is also the most positive power voltage supply pin. |
||||||||||
4 | VCOMH | COM signal deselected voltage level. A capacitor should be connected between this pin and VSS. |
||||||||||
5 | VLSS | Analog system ground pin. | ||||||||||
6~13 | D7~D0 | Host Data Input/Output Bus These pins are 8-bit bi-directional data bus to be connected to the microprocessor’s data bus. When serial mode is selected, D1 will be the serial data input SDIN and D0 will be the serial clock input SCLK. |
||||||||||
14 | E/RD# | Read/Write Enable or Read This pin is MCU interface input. When interfacing to a 68XX-series microprocessor, this pin will be used as the Enable (E) signal. Read/write operation is initiated when this pin is pulled high and the CS# is pulled low. When connecting to an 80XX-microprocessor, this pin receives the Read (RD#) signal. Data read operation is initiated when this pin is pulled low and CS# is pulled low. When serial mode is selected, this pin must be connected to VSS. |
||||||||||
15 | R/W# | Read/Write Select or Write This pin is MCU interface input. When interfacing to a 68XX-series microprocessor, this pin will be used as Read/Write (R/W#) selection input. Pull this pin to “High” for read mode and pull it to “Low” for write mode. When 80XX interface mode is selected, this pin will be the Write (WR#) input. Data write operation is initiated when this pin is pulled low and the CS# is pulled low. When serial mode is selected, this pin must be connected to VSS. |
||||||||||
16 | BS0 | Communicating Protocol Select These pins are MCU interface selection input. See the following table:
(1) 0 is connected to VSS (2) 1 is connected to VDDIO |
||||||||||
17 | BS1 | |||||||||||
18 | D/C# | Data/Command Control This pin is Data/Command control pin connecting to the MCU. When the pin is pulled HIGH, the content at D[7:0] will be interpreted as data. When the pin is pulled LOW, the content at D[7:0] will be interpreted as command. |
||||||||||
19 | CS# | Data/Command Control This pin is the chip select input connecting to the MCU. The chip is enabled for MCU communication only when CS# is pulled LOW. |
||||||||||
20 | RES# | This pin is reset signal input. When the pin is pulled LOW, initialization of the chip is executed. Keep this pin pull HIGH during normal operation. |
||||||||||
21 | FR | This pin is No Connection pins. Nothing should be connected to this pin. This pin should be left open individually. | ||||||||||
22 | IREF | Current Reference for Brightness Adjustment This pin is segment current reference pin. A resistor should be connected between this pin and VSS. Set the current lower than 10uA. |
||||||||||
23 | N.C. | Reserved Pin The N.C. pin between function pins are reserved for compatible and flexible design. |
||||||||||
24 | VDDIO | Power Supply for I/O Pin It should be matched with the MCU interface voltage level. |
||||||||||
25 | VDD | Power Supply for Core Logic Circuit Power supply pin for core logic operation. A capacitor is required to connect between this pin and VSS |
||||||||||
26 | VCI | Power Supply for Operation VCI must always be equal to or higher than VDD and VDDIO. |
||||||||||
27 | VSL | Voltage Output Low Level for SEG Signal This is segment voltage reference pin. When external VSL is not used, this pin should be left open. When external VSL is used, this pin should connect with resistor and diode to ground. |
||||||||||
28 | VLSS | Ground of Analog Circuit These are the analog ground pins. They should be connected to VSS externally. |
||||||||||
29 | VCC | Power Supply for OLED Panel These are the most positive voltage supply pin of the chip. They must be connected to external source. |
||||||||||
30 | N.C. | Reserved Pin The N.C. pin between function pins are reserved for compatible and flexible design. |
CTP Pin Function
1 | GND | Ground |
2 | VDD | Power Supply Voltage of CTP |
3 | INT | External interrupt to the host |
4 | SDA | I2C data input and output |
5 | SCL | I2C clock input |
6 | RST | External Reset, Low is active |
7-10 | GND | Ground. |
Механические характеристики
Наименование | Измерения | Единица |
---|---|---|
Разрешение | 256 x 64 точек | - |
Габариты | 89.2 × 29.0 × 3.17 | mm |
Активная область | 76.778×19.178 | mm |
Размер пикселя | 0.278×0.278 | mm |
Шаг пикселя | 0.3×0.3 | mm |
Матрица | Пассивная | |
Цвет дисплея | монохромные | |
Рабочий цикл | 1/64 Duty | |
Шкала серого | 4 bits | |
OLED IC | SSD1322 (COF) | |
OLED Интерфейс | 6800, 8080, SPI | |
Диагональ | 3.12 дюйма | |
CTP IC | FT6336U | |
точка обнаружения | 1 | |
CTP Интерфейс | I2C | |
Поверхность | Глянцевая |
Абсолютные максимальные значения
Абсолютные максимальные значения
Параметр | Символы | Минимальный | Максимальный | Единица |
---|---|---|---|---|
Supply Voltage for Operation | VCI | -0.3 | 4 | V |
Supply Voltage for Logic | VDD | -0.5 | 2.75 | V |
Supply Voltage for I/O Pins | VDDIO | -0.5 | VCI | V |
Supply Voltage for Display | VCC | -0.5 | 20 | V |
Диапазон рабочих температур | TOP | -20 | +70 | °C |
Температура хранения | TSTG | -30 | +80 | °C |
Сенсорная панель Контроллер FT6336U
Параметр | Символы | Минимальный | Максимальный | Единица |
---|---|---|---|---|
Power Supply Voltage | VDD | -0.3 | 3.6 | V |
Электронные характеристики
DC Электронные характеристики
Наименование | Символы | Кондиция | Минимальный | Типичный | Максимальный | Единица |
---|---|---|---|---|---|---|
Supply Voltage for Operation | VCI | Note | 2.8 | 3.0 | 3.3 | V |
Напряжение питания дисплея | VCC | - | 14 | 14.5 | 15 | V |
Напряжение питания логических схем | VDD | - | 2.4 | - | 2.6 | V |
Power for I/O pins | VDDIO | - | 1.65 | VCI | V | |
Вход высокого уровня | VIH | - | 0.8×VDDIO | - | VDDIO | V |
Вход низкого уровня | VIL | - | 0 | - | 0.2×VDDIO | V |
Выход высокого уровня | VOH | - | 0.9×VDDIO | - | VDDIO | V |
Выход низкого уровня | VOL | - | 0 | - | 0.1×VDDIO | V |
50% Check Board operating Current | VCC =14.5V | - | 32 | 48 | mA |
Сенсорная панель Контроллер FT6336U
Наименование | Символы | Кондиция | Минимальный | Типичный | Максимальный | Единица |
---|---|---|---|---|---|---|
Напряжение питания | VDD | 2.8 | 3.0 | 3.3 | V | |
Высокое входное напряжение | VIH | 0.7xVDD | - | VDD | V | |
Низкое входное напряжение | VIL | -0.3 | - | 0.3xVDD | V | |
Высокое напряжение на выходе | VOH | IOH = -0.1mA | 0.7xVDD | - | - | V |
Низкое напряжение на выходе. | VOL | IOH = 0.1mA | - | - | 0.3xVDD | V |
Search keyword: 256x64 oled, oled 256x64, 3.12 oled, 3.12" oled, 3.12 дюйма oled, oled 3.12"