Model WEX025664B-CTP to zaawansowany, 3,12-calowy graficzny wyświetlacz OLED o strukturze COF, wyposażony w pojemnościowy panel dotykowy o rozdzielczości 256x64 punktów. Ten zaawansowany wyświetlacz OLED wykorzystuje układ sterownika SSD1322, obsługujący wszechstronne interfejsy 8-bitowe 6800/8080 i 3/4-linie SPI. Z wymiarami 89,2x29,0 mm, zawiera aktywną powierzchnię o wymiarach 76,778x19,178 mm.
Moduł, zdolny do wyświetlania 4-bitowej skali szarości, działa przy napięciu zasilania 3,0 V (wartość typowa) i cyklu pracy 1/64. Zaprojektowany pod kątem wszechstronności, działa niezawodnie w zakresie temperatur od -20°C do +70°C, przy temperaturze przechowywania od -30°C do +80°C. Warto zauważyć, że ten model zawiera pojemnościowy panel dotykowy (CTP) z układem FT6336U, obsługujący interfejsy I2C i oferujący precyzyjną funkcję dotyku 1-punktowego.
Moduł OLED wyróżnia się znakomitym stosunkiem kontrastu 10 000:1, co przekłada się na intensywne i wiernie odwzorowane kolory, głębokie czernie i jasne biel. To poprawia ogólną jakość obrazu, uwydatnia detale i znacznie poprawia czytelność, zwłaszcza w warunkach słabego oświetlenia, co przyczynia się do immersyjnego doświadczenia wizualnego.
Moduł OLED nadaje się do różnorodnych zastosowań, w tym urządzeń ścienno-metrycznych, aplikacji domowych, systemów POS, systemów Cloud/IoT, przenośnych instrumentów, inteligentnych urządzeń technologicznych, systemów energetycznych, aplikacji samochodowych, systemów komunikacji i instrumentów medycznych. Klienci pragnący aktualizacji z tradycyjnych wyświetlaczy STN na wyświetlacze OLED z pewnością zainteresują się tym modelem, z uwagi na szeroki zakres formatów pikseli punktów dostosowanych do rozwiązań OLED.
Dodatkowo, linia produktów z tego samego rodzaju paneli OLED oferuje różne alternatywy:
Seria WEN025664B-CTP z ramą metalową, PCB i ekranem dotykowym CTP.
Rysunek
Data source ref: WEX025664BWPP3D00000
Specyfikacja
Dane mechaniczne
Rzecz
Wymiar
Jednostka
Matryca punktowa
256 x 64 pikseli
-
Wymiary modułu
89.2 × 29.0 × 3.17
mm
Obszar aktywny
76.778×19.178
mm
Wielkość piksela
0.278×0.278
mm
Raster pomiędzy pikselami
0.3×0.3
mm
Tryb wyświetlania
matryca
Kolor wyświetlacza
Monochromatyczny
Drive Duty
1/64 Duty
Skala szarości
4 bits
OLED IC
SSD1322 (COF)
OLED Interfejs
6800, 8080, SPI
Rozmiar (Przekątna)
3.12 calowy
CTP IC
FT6336U
Punkty dotyku
1
CTP Interfejs
I2C
Powierzchnia
Normal Glare
Bezwzględne oceny maksymalne
Bezwzględne oceny maksymalne
Parameter
Symbol
Minimalna wartość
Maksymalna wartość
Jednostka
Supply Voltage for Operation
VCI
-0.3
4
V
Supply Voltage for Logic
VDD
-0.5
2.75
V
Supply Voltage for I/O Pins
VDDIO
-0.5
VCI
V
Supply Voltage for Display
VCC
-0.5
20
V
Temperatura pracy
TOP
-20
+70
°C
Temperatura przechowywania
TSTG
-30
+80
°C
Touch Panel kontroler FT6336U
Parameter
Symbol
Minimalna wartość
Maksymalna wartość
Jednostka
Power Supply Voltage
VDD
-0.3
3.6
V
Parametry elektryczne
DC Parametry elektryczne
Rzecz
Symbol
Stan
Minimalna wartość
Typowa wartość
Maksymalna wartość
Jednostka
Supply Voltage for Operation
VCI
Note
2.8
3.0
3.3
V
Supply Voltage for Display
VCC
-
14
14.5
15
V
Logic supply voltage
VDD
-
2.4
-
2.6
V
Power for I/O pins
VDDIO
-
1.65
VCI
V
High Level Input
VIH
-
0.8×VDDIO
-
VDDIO
V
Low Level Input
VIL
-
0
-
0.2×VDDIO
V
High Level Output
VOH
-
0.9×VDDIO
-
VDDIO
V
Low Level Output
VOL
-
0
-
0.1×VDDIO
V
50% Check Board operating Current
VCC =14.5V
-
32
48
mA
Touch Panel kontroler FT6336U
Rzecz
Symbol
Stan
Minimalna wartość
Typowa wartość
Maksymalna wartość
Jednostka
Supply Voltage
VDD
2.8
3.0
3.3
V
Input High Volt.
VIH
0.7xVDD
-
VDD
V
Input Low Volt.
VIL
-0.3
-
0.3xVDD
V
Output High Volt.
VOH
IOH = -0.1mA
0.7xVDD
-
-
V
Output Low Volt.
VOL
IOH = 0.1mA
-
-
0.3xVDD
V
Funkcja pinów interfejsu
No.
Symbol
Funkcja
1
N.C.
Reserved Pin
The N.C. pin between function pins are reserved for compatible and flexible design.
2
VSS
Ground.
3
VCC
Power supply for panel driving voltage.
This is also the most positive power voltage supply pin.
4
VCOMH
COM signal deselected voltage level.
A capacitor should be connected between this pin and VSS.
5
VLSS
Analog system ground pin.
6~13
D7~D0
Host Data Input/Output Bus
These pins are 8-bit bi-directional data bus to be connected to the microprocessor’s data bus.
When serial mode is selected, D1 will be the serial data input SDIN and D0 will be the serial clock input SCLK.
14
E/RD#
Read/Write Enable or Read
This pin is MCU interface input.
When interfacing to a 68XX-series microprocessor, this pin will be used as the Enable (E) signal. Read/write operation is initiated when this pin is pulled high and the CS# is pulled low.
When connecting to an 80XX-microprocessor, this pin receives the Read (RD#) signal. Data read operation is initiated when this pin is pulled low and CS# is pulled low.
When serial mode is selected, this pin must be connected to VSS.
15
R/W#
Read/Write Select or Write
This pin is MCU interface input. When interfacing to a 68XX-series microprocessor, this pin will be used as Read/Write (R/W#) selection input. Pull this pin to “High” for read mode and pull it to “Low” for write mode.
When 80XX interface mode is selected, this pin will be the Write (WR#) input. Data write operation is initiated when this pin is pulled low and the CS# is pulled low.
When serial mode is selected, this pin must be connected to VSS.
16
BS0
Communicating Protocol Select
These pins are MCU interface selection input. See the following table:
BS[2:0]
Interface
00
4 line SPI
01
3 line SPI
10
8-bit 8080 parallel
11
8-bit 6800 parallel
Note
(1) 0 is connected to VSS
(2) 1 is connected to VDDIO
17
BS1
18
D/C#
Data/Command Control
This pin is Data/Command control pin connecting to the MCU.
When the pin is pulled HIGH, the content at D[7:0] will be interpreted as data.
When the pin is pulled LOW, the content at D[7:0] will be interpreted as command.
19
CS#
Data/Command Control
This pin is the chip select input connecting to the MCU. The chip is enabled for MCU communication only when CS# is pulled LOW.
20
RES#
This pin is reset signal input.
When the pin is pulled LOW, initialization of the chip is executed.
Keep this pin pull HIGH during normal operation.
21
FR
This pin is No Connection pins. Nothing should be connected to this pin. This pin should be left open individually.
22
IREF
Current Reference for Brightness Adjustment
This pin is segment current reference pin. A resistor should be connected between this pin and VSS. Set the current lower than 10uA.
23
N.C.
Reserved Pin
The N.C. pin between function pins are reserved for compatible and flexible design.
24
VDDIO
Power Supply for I/O Pin
It should be matched with the MCU interface voltage level.
25
VDD
Power Supply for Core Logic Circuit
Power supply pin for core logic operation. A capacitor is required to connect between this pin and VSS
26
VCI
Power Supply for Operation
VCI must always be equal to or higher than VDD and VDDIO.
27
VSL
Voltage Output Low Level for SEG Signal
This is segment voltage reference pin.
When external VSL is not used, this pin should be left open.
When external VSL is used, this pin should connect with resistor and diode to ground.
28
VLSS
Ground of Analog Circuit
These are the analog ground pins. They should be connected to VSS externally.
29
VCC
Power Supply for OLED Panel
These are the most positive voltage supply pin of the chip. They must be connected to external source.
30
N.C.
Reserved Pin
The N.C. pin between function pins are reserved for compatible and flexible design.
Klikając „Zezwól na wszystkie pliki cookie”, zgadzasz się na przechowywanie plików cookie na swoim urządzeniu w celu usprawnienia nawigacji po witrynie, analizy korzystania z witryny oraz wspierania naszych działań marketingowych i dotyczących wydajności. Więcej informacji na ten temat znajdziesz w naszej polityce. Polityka prywatności