私たちはあなたのプライバシーを大切にします
「すべてのクッキーを許可」をクリックすると、サイトのナビゲーションを向上させ、サイト使用状況を分析し、マーケティングおよびパフォーマンスの取り組みを支援するために、クッキーをデバイスに保存することに同意したことになります。この件に関する詳細情報は、ポリシーをご覧ください。プライバシーポリシー
WEX025664B-CTPは解像度256x64ドットの3.12インチのCOF構造のグラフィックOLEDディスプレイで、モジュールに静電容量式タッチパネルが貼り付けれらた製品です。SSD1322 ICが組み込まれて、6800/8080 8ビットパラレル及びSPIインターフェイスを介して通信できます。4ビットのグレースケールとロジックの電源電圧は2.8Vから3.3Vまでで、標準値は3.0Vにします。
ディスプレイへの供給電圧は14.5Vで、駆動デューティが1/64です。タッチパネルICについて、FT6336Uを採用して1つの検出ポイントであるI2Cインターフェイスをサポートします。このモジュールは金属製のフレームオプションが有りますので、ご注意ください。
CTPモデルを備えたこの3.12インチWEX025664Bはスマートホームアプリケーション、インテリジェントテクノロジーデバイス、メーターデバイス、産業用制御システム、医療機器等に最適で、操作温度範囲は-20℃から+70℃で、保存温度範囲は-30℃から+ 80℃です。
同じOLEDパネルのモデルにはさまざまな選択肢があります:項目 | 仕様 | 単位 |
---|---|---|
ドットマトリックス | 256 x 64 Dots | - |
モジュールサイズ | 89.2 × 29.0 × 3.17 | mm |
アクティブエリア | 76.778×19.178 | mm |
ドットサイズ | 0.278×0.278 | mm |
ドットピッチ | 0.3×0.3 | mm |
表示モード | パッシブマトリクス | |
発光色 | モノクロ | |
駆動方法 | 1/64 Duty | |
グレースケール | 4 bits | |
OLED IC | SSD1322 (COF) | |
OLED インターフェイス | 6800, 8080, SPI | |
表示サイズ(対角線) | 3.12 インチ | |
CTP IC | FT6336U | |
検出ポイント | 1 | |
CTP インターフェイス | I2C | |
表面処理 | グレア |
パラメーター | 記号 | 最小値 | 最大値 | 単位 |
---|---|---|---|---|
操作電源電圧 | VCI | -0.3 | 4 | V |
ロジック電源電圧 | VDD | -0.5 | 2.75 | V |
I/O Pins 電源電圧 | VDDIO | -0.5 | VCI | V |
Display電源電圧 | VCC | -0.5 | 20 | V |
操作温度 | TOP | -20 | +70 | °C |
保存温度 | TSTG | -30 | +80 | °C |
パラメーター | 記号 | 最小値 | 最大値 | 単位 |
---|---|---|---|---|
電源電圧 | VDD | -0.3 | 3.6 | V |
項目 | 記号 | 条件 | 最小値 | 典型値 | 最大値 | 単位 |
---|---|---|---|---|---|---|
操作電源電圧 | VCI | Note | 2.8 | 3.0 | 3.3 | V |
Display電源電圧 | VCC | - | 14 | 14.5 | 15 | V |
ロジック電源電圧 | VDD | - | 2.4 | - | 2.6 | V |
I / Oピンの電源 | VDDIO | - | 1.65 | VCI | V | |
高レベル入力 | VIH | - | 0.8×VDDIO | - | VDDIO | V |
低レベル入力 | VIL | - | 0 | - | 0.2×VDDIO | V |
高レベル出力 | VOH | - | 0.9×VDDIO | - | VDDIO | V |
低レベル出力 | VOL | - | 0 | - | 0.1×VDDIO | V |
50% Check Board operating Current | VCC =14.5V | - | 32 | 48 | mA |
項目 | 記号 | 条件 | 最小値 | 典型値 | 最大値 | 単位 |
---|---|---|---|---|---|---|
電源電圧 | VDD | 2.8 | 3.0 | 3.3 | V | |
高レベル入力 | VIH | 0.7xVDD | - | VDD | V | |
低レベル入力 | VIL | -0.3 | - | 0.3xVDD | V | |
高レベル出力 | VOH | IOH = -0.1mA | 0.7xVDD | - | - | V |
低レベル出力 | VOL | IOH = 0.1mA | - | - | 0.3xVDD | V |
No. | 記号 | 説明 | ||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|
1 | N.C. | Reserved Pin The N.C. pin between function pins are reserved for compatible and flexible design. |
||||||||||
2 | VSS | Ground. | ||||||||||
3 | VCC | Power supply for panel driving voltage. This is also the most positive power voltage supply pin. |
||||||||||
4 | VCOMH | COM signal deselected voltage level. A capacitor should be connected between this pin and VSS. |
||||||||||
5 | VLSS | Analog system ground pin. | ||||||||||
6~13 | D7~D0 | Host Data Input/Output Bus These pins are 8-bit bi-directional data bus to be connected to the microprocessor’s data bus. When serial mode is selected, D1 will be the serial data input SDIN and D0 will be the serial clock input SCLK. |
||||||||||
14 | E/RD# | Read/Write Enable or Read This pin is MCU interface input. When interfacing to a 68XX-series microprocessor, this pin will be used as the Enable (E) signal. Read/write operation is initiated when this pin is pulled high and the CS# is pulled low. When connecting to an 80XX-microprocessor, this pin receives the Read (RD#) signal. Data read operation is initiated when this pin is pulled low and CS# is pulled low. When serial mode is selected, this pin must be connected to VSS. |
||||||||||
15 | R/W# | Read/Write Select or Write This pin is MCU interface input. When interfacing to a 68XX-series microprocessor, this pin will be used as Read/Write (R/W#) selection input. Pull this pin to “High” for read mode and pull it to “Low” for write mode. When 80XX interface mode is selected, this pin will be the Write (WR#) input. Data write operation is initiated when this pin is pulled low and the CS# is pulled low. When serial mode is selected, this pin must be connected to VSS. |
||||||||||
16 | BS0 | Communicating Protocol Select These pins are MCU interface selection input. See the following table:
(1) 0 is connected to VSS (2) 1 is connected to VDDIO |
||||||||||
17 | BS1 | |||||||||||
18 | D/C# | Data/Command Control This pin is Data/Command control pin connecting to the MCU. When the pin is pulled HIGH, the content at D[7:0] will be interpreted as data. When the pin is pulled LOW, the content at D[7:0] will be interpreted as command. |
||||||||||
19 | CS# | Data/Command Control This pin is the chip select input connecting to the MCU. The chip is enabled for MCU communication only when CS# is pulled LOW. |
||||||||||
20 | RES# | This pin is reset signal input. When the pin is pulled LOW, initialization of the chip is executed. Keep this pin pull HIGH during normal operation. |
||||||||||
21 | FR | This pin is No Connection pins. Nothing should be connected to this pin. This pin should be left open individually. | ||||||||||
22 | IREF | Current Reference for Brightness Adjustment This pin is segment current reference pin. A resistor should be connected between this pin and VSS. Set the current lower than 10uA. |
||||||||||
23 | N.C. | Reserved Pin The N.C. pin between function pins are reserved for compatible and flexible design. |
||||||||||
24 | VDDIO | Power Supply for I/O Pin It should be matched with the MCU interface voltage level. |
||||||||||
25 | VDD | Power Supply for Core Logic Circuit Power supply pin for core logic operation. A capacitor is required to connect between this pin and VSS |
||||||||||
26 | VCI | Power Supply for Operation VCI must always be equal to or higher than VDD and VDDIO. |
||||||||||
27 | VSL | Voltage Output Low Level for SEG Signal This is segment voltage reference pin. When external VSL is not used, this pin should be left open. When external VSL is used, this pin should connect with resistor and diode to ground. |
||||||||||
28 | VLSS | Ground of Analog Circuit These are the analog ground pins. They should be connected to VSS externally. |
||||||||||
29 | VCC | Power Supply for OLED Panel These are the most positive voltage supply pin of the chip. They must be connected to external source. |
||||||||||
30 | N.C. | Reserved Pin The N.C. pin between function pins are reserved for compatible and flexible design. |
1 | GND | Ground |
2 | VDD | Power Supply Voltage of CTP |
3 | INT | External interrupt to the host |
4 | SDA | I2C data input and output |
5 | SCL | I2C clock input |
6 | RST | External Reset, Low is active |
7-10 | GND | Ground. |
「すべてのクッキーを許可」をクリックすると、サイトのナビゲーションを向上させ、サイト使用状況を分析し、マーケティングおよびパフォーマンスの取り組みを支援するために、クッキーをデバイスに保存することに同意したことになります。この件に関する詳細情報は、ポリシーをご覧ください。プライバシーポリシー