3.12", 256x64 Moduły graficznych COF OLED
Numer modelu WEX025664B
►Typ: graficzny
►Struktura: COF
►Rozmiar : 3.12"
►256 x 64 matryca punktowa
►IC:SSD1322
►zasilanie 3V
►wypełnienie 1/64
►Interfejs: 6800, 8080, SPI
►Kolor wyświetlacza: biały / żółto / jasnoniebieski / zielony
►Obsługiwana skala szarości
Opis
Model WEX025664B to 3,12-calowy graficzny wyświetlacz OLED o strukturze COF. Ten wyświetlacz OLED o rozdzielczości 256x64 jest wyposażony w układ sterownika SSD1322, obsługujący interfejsy 8-bitowe 6800/8080 oraz 3/4-linie SPI. Ma wymiary zewnętrzne 88 x 27,8 mm, a aktywna powierzchnia wynosi 76,778 x 19,178 mm. Wyświetlacz obsługuje 4-bity odcieni szarości, a jego napięcie logiczne wynosi 2,5 V (wartość typowa) przy cyklu pracy 1/64. Moduł może pracować w temperaturach od -40°C do +80°C, a temperatura przechowywania wynosi od -40°C do +85°C.
Moduł OLED charakteryzuje się wysokim stosunkiem kontrastu 10 000:1, co pozwala na bardziej intensywne i wierniejsze kolory, głębsze czernie i jaśniejsze biel. To przekłada się na poprawę jakości obrazu, ostrość detali i lepszą czytelność, zwłaszcza w warunkach słabego oświetlenia. Dodatkowo, wysoki stosunek kontrastu przyczynia się do bardziej immersyjnego doświadczenia wizualnego.
Moduł OLED nadaje się do różnych zastosowań, takich jak urządzenia na ścianie/liczniki, aplikacje domowe, systemy POS, systemy Cloud/IoT, przenośne instrumenty, urządzenia technologii inteligentnej, systemy energetyczne, aplikacje samochodowe, systemy komunikacyjne i urządzenia medyczne. Klienci mogą zaktualizować swoje obecne aplikacje z tradycyjnych wyświetlaczy STN na wyświetlacze OLED, ponieważ moduł ten oferuje bardzo szeroki zakres formatów pikseli dla rozwiązań OLED.
Dodatkowo, panele OLED o tych samych wymiarach oferują różne alternatywy:- Seria WEX025664B-CTP bez ramy metalowej, PCB i z ekranem dotykowym CTP.
- Seria WEN025664B z ramką metalową i PCB.
- Seria WEN025664B-CTP z ramką metalową, PCB i ekranem dotykowym CTP.
Rysunek
Data source ref: WEX025664BWPP3N00000
Specyfikacja
Funkcja pinów interfejsu
Pin Number | Symbol | I/O | Funkcja | ||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|
1 | N.C. (GND) | P | Ground | ||||||||||
2 | VSS | P | Ground. | ||||||||||
3 | VCC | P | Power supply for panel driving voltage. This is also the most positive power voltage supply pin. |
||||||||||
4 | VCOMH | P | COM signal deselected voltage level. A capacitor should be connected between this pin and VSS. |
||||||||||
5 | VLSS | P | Analog system ground pin. | ||||||||||
6~13 | D7~D0 | I/O | Host Data Input/Output Bus These pins are 8-bit bi-directional data bus to be connected to the microprocessor’s data bus. When serial mode is selected, D1 will be the serial data input SDIN and D0 will be the serial clock input SCLK. |
||||||||||
14 | E/RD# | I | Read/Write Enable or Read This pin is MCU interface input. When interfacing to a 68XX-series microprocessor, this pin will be used as the Enable (E) signal. Read/write operation is initiated when this pin is pulled high and the CS# is pulled low. When connecting to an 80XX-microprocessor, this pin receives the Read (RD#) signal. Data read operation is initiated when this pin is pulled low and CS# is pulled low. When serial mode is selected, this pin must be connected to VSS. |
||||||||||
15 | R/W# | I | Read/Write Select or Write This pin is MCU interface input. When interfacing to a 68XX-series microprocessor, this pin will be used as Read/Write (R/W#) selection input. Pull this pin to “High” for read mode and pull it to “Low” for write mode. When 80XX interface mode is selected, this pin will be the Write (WR#) input. Data write operation is initiated when this pin is pulled low and the CS# is pulled low. When serial mode is selected, this pin must be connected to VSS. |
||||||||||
16 | BS0 | I | Communicating Protocol Select These pins are MCU interface selection input. See the following table:
(1) 0 is connected to VSS (2) 1 is connected to VDDIO |
||||||||||
17 | BS1 | ||||||||||||
18 | D/C# | I | Data/Command Control This pin is Data/Command control pin connecting to the MCU. When the pin is pulled HIGH, the content at D[7:0] will be interpreted as data. When the pin is pulled LOW, the content at D[7:0] will be interpreted as command. |
||||||||||
19 | CS# | I | Data/Command Control This pin is the chip select input connecting to the MCU. The chip is enabled for MCU communication only when CS# is pulled LOW. |
||||||||||
20 | RES# | I | This pin is reset signal input. When the pin is pulled LOW, initialization of the chip is executed. Keep this pin pull HIGH during normal operation. |
||||||||||
21 | FR | O | This pin is No Connection pins. Nothing should be connected to this pin. This pin should be left open individually. | ||||||||||
22 | IREF | I | Current Reference for Brightness Adjustment This pin is segment current reference pin. A resistor should be connected between this pin and VSS. Set the current lower than 10uA. |
||||||||||
23 | N.C. | - | Reserved Pin The N.C. pin between function pins are reserved for compatible and flexible design. |
||||||||||
24 | VDDIO | P | Power Supply for I/O Pin It should be matched with the MCU interface voltage level. |
||||||||||
25 | VDD | P | Power Supply for Core Logic Circuit Power supply pin for core logic operation. A capacitor is required to connect between this pin and VSS |
||||||||||
26 | VCI | P | Power Supply for Operation VCI must always be equal to or higher than VDD and VDDIO. |
||||||||||
27 | VSL | P | Voltage Output Low Level for SEG Signal This is segment voltage reference pin. When external VSL is not used, this pin should be left open. When external VSL is used, this pin should connect with resistor and diode to ground. |
||||||||||
28 | VLSS | P | Ground of Analog Circuit These are the analog ground pins. They should be connected to VSS externally. |
||||||||||
29 | VCC | P | Power Supply for OLED Panel These are the most positive voltage supply pin of the chip. They must be connected to external source. |
||||||||||
30 | N.C. (GND) | P | Ground |
Dane mechaniczne
Rzecz | Wymiar | Jednostka |
---|---|---|
Matryca punktowa | 256 x 64 Dots | - |
Wymiary modułu | 88.0 × 27.8 × 2.15 | mm |
Obszar aktywny | 76.778×19.178 | mm |
Wielkość piksela | 0.278×0.278 | mm |
Raster pomiędzy pikselami | 0.3×0.3 | mm |
Tryb wyświetlania | matryca | |
Kolor wyświetlacza | Monochromatyczny | |
Drive Duty | 1/64 Duty | |
Gray Scale | 4 bits | |
IC | SSD1322 (COF) | |
Interfejs | 6800, 8080, SPI | |
Rozmiar | 3.12 cale |
Bezwzględne oceny maksymalne
Parameter | Symbol | Minimalna wartość | Maksymalna wartość | Jednostka |
---|---|---|---|---|
Supply Voltage for Operation | VCI | -0.3 | 4 | V |
Supply Voltage for Logic | VDD | -0.5 | 2.75 | V |
Supply Voltage for I/O Pins | VDDIO | -0.5 | VCI | V |
Supply Voltage for Display | VCC | -0.5 | 20 | V |
Temperatura pracy | TOP | -40 | 80 | °C |
Temperatura przechowywania | TSTG | -40 | 85 | °C |
Parametry elektryczne
Rzecz | Symbol | Stan | Minimalna wartość | Typowa wartość | Maksymalna wartość | Jednostka |
---|---|---|---|---|---|---|
Supply Voltage for Logic | VDD | - | 2.4 | 2.5 | 2.6 | V |
Power Supply for I/O pins | VDDIO | - | 1.65 | 3.0 | VCI | V |
Low voltage power supply | VCI | - | 2.4 | 3.0 | 3.5 | V |
Supply Voltage for Display | VCC | - | 11.5 | 14.5 | 15 | V |
High Level Input | VIH | - | 0.8×VDDIO | - | VDDIO | V |
Low Level Input | VIL | - | 0 | - | 0.2×VDDIO | V |
High Level Output | VOH | - | 0.9×VDDIO | - | VDDIO | V |
Low Level Output | VOL | - | 0 | - | 0.1×VDDIO | V |
50% Check Board operating Current | ICC | VCC =12V | - | 24 | 32 | mA |
VCC =14.5V | - | 32 | 42.5 | mA |
Search keyword: 256x64 oled, oled 256x64, 3.12 oled, 3.12" oled, 3.12 cale oled, oled 3.12, oled 3.12"