Display Grafico OLED COF Monocromatici 256x64 da 3,12 pollici
Modello numero WEX025664B
►Tipo: grafico
►Struttura: COF
►Dimensione: 3.12 pollici
►256 x 64 a matrice di punti
►IC:SSD1322
►Alimentatore 3V
►1/64 duty
►Interfaccia: 6800, 8080, SPI
►Colore display: Bianco / Giallo / Cielo blu / Verde
►Support Grayscale
Descrizione
Il modello WEX025664B è un display grafico OLED COF da 3,12 pollici con una risoluzione di 256x64 pixel. Questo display OLED da 3,12 pollici è dotato di un circuito integrato driver SSD1322 che supporta interfacce a 8 bit 6800/8080 e a 3/4 linee SPI. Ha dimensioni esterne di 88 x 27,8 mm, con un'area attiva di 76,778 x 19,178 mm. Il display supporta una scala di grigi a 4 bit, e la tensione logica è di 2,5 V (valore tipico) con un ciclo di lavoro di 1/64. Il modulo può operare a temperature comprese tra -40°C e +80°C, mentre la temperatura di conservazione va da -40°C a +85°C.
Il modulo OLED presenta un elevato rapporto di contrasto di 10.000:1, consentendo colori più vividi e fedeli alla realtà, neri più profondi e bianchi più luminosi. Ciò si traduce in una migliore qualità dell'immagine, dettagli più nitidi e una migliore leggibilità, specialmente in ambienti a bassa illuminazione. Inoltre, l'alto rapporto di contrasto contribuisce a un'esperienza visiva più coinvolgente.
Il modulo OLED è adatto a varie applicazioni come dispositivi da parete/contatori, applicazioni domestiche, sistemi POS, sistemi Cloud/IoT, strumenti portatili, dispositivi di tecnologia intelligente, sistemi energetici, applicazioni automobilistiche, sistemi di comunicazione e strumenti medici. I clienti possono aggiornare le loro attuali applicazioni dai display tradizionali STN a quelli OLED, poiché il modulo offre una vasta gamma di formati di pixel punti per soluzioni OLED.
Inoltre, pannelli OLED con le stesse dimensioni offrono diverse alternative:- Serie WEX025664B-CTP senza telaio metallico, PCB e con touchscreen CTP.
- Serie WEN025664B con telaio metallico e PCB.
- Serie WEN025664B-CTP con telaio metallico, PCB e touchscreen CTP.
DISEGNO
Data source ref: WEX025664BWPP3N00000
SPECIFICHE TECNICHE
Funzione dei Pin di Interfaccia
Pin Number | Simbolo | I/O | Funzione | ||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|
1 | N.C. (GND) | P | Ground | ||||||||||
2 | VSS | P | Ground. | ||||||||||
3 | VCC | P | Power supply for panel driving voltage. This is also the most positive power voltage supply pin. |
||||||||||
4 | VCOMH | P | COM signal deselected voltage level. A capacitor should be connected between this pin and VSS. |
||||||||||
5 | VLSS | P | Analog system ground pin. | ||||||||||
6~13 | D7~D0 | I/O | Host Data Input/Output Bus These pins are 8-bit bi-directional data bus to be connected to the microprocessor’s data bus. When serial mode is selected, D1 will be the serial data input SDIN and D0 will be the serial clock input SCLK. |
||||||||||
14 | E/RD# | I | Read/Write Enable or Read This pin is MCU interface input. When interfacing to a 68XX-series microprocessor, this pin will be used as the Enable (E) signal. Read/write operation is initiated when this pin is pulled high and the CS# is pulled low. When connecting to an 80XX-microprocessor, this pin receives the Read (RD#) signal. Data read operation is initiated when this pin is pulled low and CS# is pulled low. When serial mode is selected, this pin must be connected to VSS. |
||||||||||
15 | R/W# | I | Read/Write Select or Write This pin is MCU interface input. When interfacing to a 68XX-series microprocessor, this pin will be used as Read/Write (R/W#) selection input. Pull this pin to “High” for read mode and pull it to “Low” for write mode. When 80XX interface mode is selected, this pin will be the Write (WR#) input. Data write operation is initiated when this pin is pulled low and the CS# is pulled low. When serial mode is selected, this pin must be connected to VSS. |
||||||||||
16 | BS0 | I | Communicating Protocol Select These pins are MCU interface selection input. See the following table:
(1) 0 is connected to VSS (2) 1 is connected to VDDIO |
||||||||||
17 | BS1 | ||||||||||||
18 | D/C# | I | Data/Command Control This pin is Data/Command control pin connecting to the MCU. When the pin is pulled HIGH, the content at D[7:0] will be interpreted as data. When the pin is pulled LOW, the content at D[7:0] will be interpreted as command. |
||||||||||
19 | CS# | I | Data/Command Control This pin is the chip select input connecting to the MCU. The chip is enabled for MCU communication only when CS# is pulled LOW. |
||||||||||
20 | RES# | I | This pin is reset signal input. When the pin is pulled LOW, initialization of the chip is executed. Keep this pin pull HIGH during normal operation. |
||||||||||
21 | FR | O | This pin is No Connection pins. Nothing should be connected to this pin. This pin should be left open individually. | ||||||||||
22 | IREF | I | Current Reference for Brightness Adjustment This pin is segment current reference pin. A resistor should be connected between this pin and VSS. Set the current lower than 10uA. |
||||||||||
23 | N.C. | - | Reserved Pin The N.C. pin between function pins are reserved for compatible and flexible design. |
||||||||||
24 | VDDIO | P | Power Supply for I/O Pin It should be matched with the MCU interface voltage level. |
||||||||||
25 | VDD | P | Power Supply for Core Logic Circuit Power supply pin for core logic operation. A capacitor is required to connect between this pin and VSS |
||||||||||
26 | VCI | P | Power Supply for Operation VCI must always be equal to or higher than VDD and VDDIO. |
||||||||||
27 | VSL | P | Voltage Output Low Level for SEG Signal This is segment voltage reference pin. When external VSL is not used, this pin should be left open. When external VSL is used, this pin should connect with resistor and diode to ground. |
||||||||||
28 | VLSS | P | Ground of Analog Circuit These are the analog ground pins. They should be connected to VSS externally. |
||||||||||
29 | VCC | P | Power Supply for OLED Panel These are the most positive voltage supply pin of the chip. They must be connected to external source. |
||||||||||
30 | N.C. (GND) | P | Ground |
Dati meccanici
Articolo | Dimensioni | Unità |
---|---|---|
A matrice di punti | 256 x 64 Dots | - |
Dimensione del modulo | 88.0 × 27.8 × 2.15 | mm |
Area attiva | 76.778×19.178 | mm |
Dimensioni del Dot | 0.278×0.278 | mm |
Passo del Dot | 0.3×0.3 | mm |
Modalità display | Matrice passiva | |
Colore display | monocromatici | |
Drive Duty | 1/64 Duty | |
Gray Scale | 4 bits | |
IC | SSD1322 (COF) | |
Interfaccia | 6800, 8080, SPI | |
Dimensione (Diagonale) | 3.12 pollici |
Valori massimi assoluti
Parameter | Simbolo | Valore Min | Valore massimo | Unità |
---|---|---|---|---|
Supply Voltage for Operation | VCI | -0.3 | 4 | V |
Supply Voltage for Logic | VDD | -0.5 | 2.75 | V |
Supply Voltage for I/O Pins | VDDIO | -0.5 | VCI | V |
Supply Voltage for Display | VCC | -0.5 | 20 | V |
Temperatura di lavoro | TOP | -40 | 80 | °C |
Temperatura di stock | TSTG | -40 | 85 | °C |
Caratteristiche elettriche
Articolo | Simbolo | Condizione | Valore Min | Valore tipico | Valore massimo | Unità |
---|---|---|---|---|---|---|
Supply Voltage for Logic | VDD | - | 2.4 | 2.5 | 2.6 | V |
Power Supply for I/O pins | VDDIO | - | 1.65 | 3.0 | VCI | V |
Low voltage power supply | VCI | - | 2.4 | 3.0 | 3.5 | V |
Supply Voltage for Display | VCC | - | 11.5 | 14.5 | 15 | V |
High Level Input | VIH | - | 0.8×VDDIO | - | VDDIO | V |
Low Level Input | VIL | - | 0 | - | 0.2×VDDIO | V |
High Level Output | VOH | - | 0.9×VDDIO | - | VDDIO | V |
Low Level Output | VOL | - | 0 | - | 0.1×VDDIO | V |
50% Check Board operating Current | ICC | VCC =12V | - | 24 | 32 | mA |
VCC =14.5V | - | 32 | 42.5 | mA |
Search keyword: 256x64 oled, oled 256x64, 3.12 oled, 3.12" oled, 3.12 pollici oled, oled 3.12, oled 3.12"