繪圖型 3.12吋 COF OLED 顯示器 256x64 - WEX025664B

繪圖型 3.12吋 COF OLED 顯示器 256x64

型號 WEX025664B

►類型:繪圖型
►結構: COF
►尺寸: 3.12吋
►256 x 64 點陣
►IC：SSD1322
►3V電源電壓
►1/64 duty
►介面: 6800, 8080, SPI
►發光顏色: 白色 / 黃色 / 天空藍 / 綠色
►支援灰階

PDF下載

索取Demo Code 產品詢問

上一個產品回分類頁下一個產品

產品敘述

WEX025664B為3.12吋為COF結構繪圖型OLED，解析度256x64 dots。此3.12吋 OLED 顯示器內建SSD1322 IC，可支援8-bits 6800/8080 和 3線/4線 SPI介面。模組外觀尺寸為 88 x 27.8 mm, 顯示區域尺寸為 76.778 x 19.178 mm。此OLED可支援4-bits灰階，邏輯電壓典型值為2.5V，驅動方式 1/64 duty。模組工作溫度範圍-40°C ~ +80°C;儲存溫度範圍-40°C ~ +85°C。

OLED 模組具有 10,000:1 的高對比度，可呈現更鮮豔、逼真的色彩、更深的黑色和更明亮的白色。這可以提高影像品質、提供更清晰的細節並提高可讀性，尤其是在低光源環境下。此外，高對比度有助於提供更身臨其境的觀看體驗，非常適合視覺清晰度和細節至關重要的應用。

華凌光電 COF OLED模組系列非常適合牆面型(wall devices) 與測量儀器(meter devices)，例如POS系統、雲端/物聯網系統、手持式產品、智能科技與智慧能源系統、車載與通訊設備以及醫療儀器等等，客戶能便利地將原來產品上的STN顯示器輕易地升級到OLED顯示器，因為華凌光電提供非常多樣化與廣度的OLED尺寸與OLED產品提升解決方案供客戶產品升級。

與此型號相同的OLED面板提供了多種選擇：

WEX025664B-CTP系列，無鐵框、PCB，配備CTP觸控面板。
WEN025664B系列，配備鐵框、PCB。
WEN025664B-CTP系列，配備鐵框、PCB、CTP觸控面板。

規格圖

WEX025664B - OLED 256x64, 3.12 inch OLED Display Drawing

Data source ref: WEX025664BWPP3N00000

產品規格

Pin功能定義

Pin Number

符號

I/O

功能說明

N.C. (GND)

Ground

VSS

Ground.

VCC

Power supply for panel driving voltage.
This is also the most positive power voltage supply pin.

VCOMH

COM signal deselected voltage level.
A capacitor should be connected between this pin and VSS.

VLSS

Analog system ground pin.

6~13

D7~D0

I/O

Host Data Input/Output Bus
These pins are 8-bit bi-directional data bus to be connected to the microprocessor’s data bus.
When serial mode is selected, D1 will be the serial data input SDIN and D0 will be the serial clock input SCLK.

E/RD#

Read/Write Enable or Read
This pin is MCU interface input.
When interfacing to a 68XX-series microprocessor, this pin will be used as the Enable (E) signal. Read/write operation is initiated when this pin is pulled high and the CS# is pulled low.
When connecting to an 80XX-microprocessor, this pin receives the Read (RD#) signal. Data read operation is initiated when this pin is pulled low and CS# is pulled low.
When serial mode is selected, this pin must be connected to VSS.

R/W#

Read/Write Select or Write
This pin is MCU interface input. When interfacing to a 68XX-series microprocessor, this pin will be used as Read/Write (R/W#) selection input. Pull this pin to “High” for read mode and pull it to “Low” for write mode.
When 80XX interface mode is selected, this pin will be the Write (WR#) input. Data write operation is initiated when this pin is pulled low and the CS# is pulled low.
When serial mode is selected, this pin must be connected to VSS.

BS0

Communicating Protocol Select
These pins are MCU interface selection input. See the following table:

BS:[1:0]	Bus Interface Selection
00	4 line SPI
01	3 line SPI
10	8-bit 8080 parallel
11	8-bit 6800 parallel

Note
(1) 0 is connected to VSS
(2) 1 is connected to VDDIO

BS1

D/C#

Data/Command Control
This pin is Data/Command control pin connecting to the MCU.
When the pin is pulled HIGH, the content at D[7:0] will be interpreted as data.
When the pin is pulled LOW, the content at D[7:0] will be interpreted as command.

CS#

Data/Command Control
This pin is the chip select input connecting to the MCU. The chip is enabled for MCU communication only when CS# is pulled LOW.

RES#

This pin is reset signal input.
When the pin is pulled LOW, initialization of the chip is executed.
Keep this pin pull HIGH during normal operation.

This pin is No Connection pins. Nothing should be connected to this pin. This pin should be left open individually.

IREF

Current Reference for Brightness Adjustment
This pin is segment current reference pin. A resistor should be connected between this pin and VSS. Set the current lower than 10uA.

N.C.

Reserved Pin
The N.C. pin between function pins are reserved for compatible and flexible design.

VDDIO

Power Supply for I/O Pin
It should be matched with the MCU interface voltage level.

VDD

Power Supply for Core Logic Circuit
Power supply pin for core logic operation. A capacitor is required to connect between this pin and VSS

VCI

Power Supply for Operation
VCI must always be equal to or higher than VDD and VDDIO.

VSL

Voltage Output Low Level for SEG Signal
This is segment voltage reference pin.
When external VSL is not used, this pin should be left open.
When external VSL is used, this pin should connect with resistor and diode to ground.

VLSS

Ground of Analog Circuit
These are the analog ground pins. They should be connected to VSS externally.

VCC

Power Supply for OLED Panel
These are the most positive voltage supply pin of the chip. They must be connected to external source.

N.C. (GND)

Ground

規格說明

項目	尺寸	單位
點陣	256 x 64 Dots	－
模組尺寸	88.0 × 27.8 × 2.15	mm
有效區域	76.778×19.178	mm
像素大小	0.278×0.278	mm
像素間距	0.3×0.3	mm
顯示模式	被動矩陣
發光顏色	單色
驅動方式	1/64 Duty
灰階	4 bits
IC	SSD1322 (COF)
介面	6800, 8080, SPI
尺寸	3.12 吋

最大絕對額定

參數	符號	最小值	最大值	單位
工作電源電壓	VCI	-0.3	4	V
邏輯電源電壓	VDD	-0.5	2.75	V
I/O pin 供電電壓	VDDIO	-0.5	VCI	V
顯示電源電壓	VCC	-0.5	20	V
工作溫度	TOP	-40	80	°C
儲存溫度	TSTG	-40	85	°C

電氣特性

項目	符號	條件	最小值	典型值	最大值	單位
邏輯電源電壓	VDD	－	2.4	2.5	2.6	V
I/O Pin 電源	VDDIO	－	1.65	3.0	VCI	V
低壓電源	VCI	－	2.4	3.0	3.5	V
顯示電源電壓	VCC	－	11.5	14.5	15	V
輸入高準位	VIH	－	0.8×VDDIO	－	VDDIO	V
輸入低準位	VIL	－	0	－	0.2×VDDIO	V
輸出高準位	VOH	－	0.9×VDDIO	－	VDDIO	V
輸出低準位	VOL	－	0	－	0.1×VDDIO	V
50%顯示畫面耗電流	ICC	VCC =12V	－	24	32	mA
50%顯示畫面耗電流	ICC	VCC =14.5V	－	32	42.5	mA