Strona główna Produkty Wyświetlacz OLED dotykowy OLED Wyświetlacz WEN025664A-CTP

Wyświetlacz OLED 2,8 " 256x64 z panelem dotykowym

Numer modelu WEN025664A-CTP

►Typ: graficzny
►Struktura: COF+FR+PCB
►Rozmiar: 2.8"
►256×64 matryca punktowa
►wbudowany kontroler SSD1322
►zasilanie 3V
►cykl wypełnienia 1/64
►interfejs: 6800, 8080, SPI
►Panel dotykowy : pojemnościowy panel dotykowy (CTP)
►Detect Point : 1 Finger
►Kolor wyświetlacza: biały / żółto / zielony
►Support Grayscale

Rysunek

2.8 inch 256x64 OLED Display with Touch Panel Support Grayscale - WEN025664A-CTP

Data source ref: WEN025664AWPP3D00000

Specyfikacja

Funkcja pinów interfejsu

Pin Number Symbol I/O Funkcja
1 VSS P Ground.
2 VDD P Power Supply for Core Logic Circuit
Power supply pin for core logic operation. A capacitor is required to connect between this pin and VSS
3 N.C. P Reserved Pin
The N.C. pin between function pins are reserved for compatible and flexible design.
4 D/C# I Data/Command Control
This pin is Data/Command control pin connecting to the MCU.
When the pin is pulled HIGH, the content at D[7:0] will be interpreted as data.
When the pin is pulled LOW, the content at D[7:0] will be interpreted as command.
5 R/W#
(WR#)
I Read/Write Select or Write
This pin is MCU interface input. When interfacing to a 68XX-series microprocessor, this pin will be used as Read/Write (R/W#) selection input. Pull this pin to “High” for read mode and pull it to “Low” for write mode.
When 80XX interface mode is selected, this pin will be the Write (WR#) input. Data write operation is initiated when this pin is pulled low and the CS# is pulled low.
When serial mode is selected, this pin must be connected to VSS.
6 E/RD# I Read/Write Enable or Read
This pin is MCU interface input.
When interfacing to a 68XX-series microprocessor, this pin will be used as the Enable (E) signal. Read/write operation is initiated when this pin is pulled high and the CS# is pulled low.
When connecting to an 80XX-microprocessor, this pin receives the Read (RD#) signal. Data read operation is initiated when this pin is pulled low and CS# is pulled low.
When serial mode is selected, this pin must be connected to VSS.
7~14 DB0 I/O Host Data Input/Output Bus
These pins are 8-bit bi-directional data bus to be connected to the microprocessor’s data bus.
When serial mode is selected, D1 will be the serial data input SDIN and D0 will be the serial clock input SCLK.
DB1
DB2
DB3
DB4
DB5
DB6
DB7
15 NC P Reserved Pin
The N.C. pin between function pins are reserved for compatible and flexible design.
16 RES# I This pin is reset signal input.
When the pin is pulled LOW, initialization of the chip is executed.
Keep this pin pull HIGH during normal operation.
17 CS# I Data/Command Control
This pin is the chip select input connecting to the MCU. The chip is enabled for MCU communication only when CS# is pulled LOW.
18 NC P Reserved Pin
The N.C. pin between function pins are reserved for compatible and flexible design.
19 BS1 I Communicating Protocol Select
These pins are MCU interface selection input. See the following table:
BS[1:0] Interface
00 4 line SPI
01 3 line SPI
10 8-bit 8080 parallel
11 8-bit 6800 parallel

Note
(1) 0 is connected to VSS
(2) 1 is connected to VDD
20 BS0
21 TP_SCK I I2C clock input
22 TP_SDA I I2C data input and output
23 TP_INT I External interrupt to the host
24 TP_RST I External Reset, Low is active

Dane mechaniczne

Rzecz Wymiar Jednostka
Matryca punktowa 256 × 64 pikseli
Wymiary modułu 85.0 × 39.8 ×7.83 mm
Obszar aktywny 69.1 × 17.26 mm
Wielkość piksela 0.248×0.248 mm
Raster pomiędzy pikselami 0.27×0.27 mm
Tryb wyświetlania matryca
Kolor wyświetlacza Monochromatyczny
Drive Duty 1/64 Duty
OLED IC SSD1322 (COF)
OLED Interfejs 6800, 8080, SPI
Rozmiar (Przekątna) 2.8 calowy
CTP IC FT6336U
Detect Point 1
CTP Interfejs I2C
Powierzchnia Normal Glare

Bezwzględne oceny maksymalne

Bezwzględne oceny maksymalne

Parameter Symbol Minimalna wartość Maksymalna wartość Jednostka
Supply Voltage for Display VDD -0.3 4 V
Temperatura pracy TOP -20 +70 °C
Temperatura przechowywania TSTG -30 +80 °C

Parametry elektryczne

DC Parametry elektryczne

Rzecz Symbol Stan Minimalna wartość Typowa wartość Maksymalna wartość Jednostka
Logic supply voltage VDD 2.8 3.0 3.3 V
High Level Input VIH 0.8×VDD VDD V
Low Level Input VIL 0 0.2×VDD V
High Level Output VOH 0.9×VDD VDD V
Low Level Output VOL 0 0.1×VDD V
50% Check Board operating Current VDD =3V 125 250 mA

Search keyword: 256x64 oled, oled 256x64, 2.8 oled, 2.8" oled, 2.8 calowy oled, oled 2.8"

go top
close