Home Productos Pantalla OLED Módulos OLED Con Táctil WEN025664A-CTP

Pantalla OLED de 2.8 "y 256x64 con panel táctil

Modelo Nº WEN025664A-CTP

►Tipo : Gráfico
►Estructura : COF+FR+PCB
►Tamaño : 2.8"
►Matriz de puntos 256×64
►Controlador integrado SSD1322
►Fuente de alimentación de 3V
►1/64 duty cycle
►Interfaz: 6800, 8080, SPI
►Pantalla táctil : Con panel táctil capacitivo (CTP)
►Detect Point : 1 Finger
►Color de la pantalla: Blanco / Amarillo / Verde
►Support Grayscale

DIBUJO

2.8 inch 256x64 OLED Display with Touch Panel Support Grayscale - WEN025664A-CTP

Data source ref: WEN025664AWPP3D00000

ESPECIFICACIONES

Función interfaz Pin

Pin Number Símbolo I/O Función
1 VSS P Ground.
2 VDD P Power Supply for Core Logic Circuit
Power supply pin for core logic operation. A capacitor is required to connect between this pin and VSS
3 N.C. P Reserved Pin
The N.C. pin between function pins are reserved for compatible and flexible design.
4 D/C# I Data/Command Control
This pin is Data/Command control pin connecting to the MCU.
When the pin is pulled HIGH, the content at D[7:0] will be interpreted as data.
When the pin is pulled LOW, the content at D[7:0] will be interpreted as command.
5 R/W#
(WR#)
I Read/Write Select or Write
This pin is MCU interface input. When interfacing to a 68XX-series microprocessor, this pin will be used as Read/Write (R/W#) selection input. Pull this pin to “High” for read mode and pull it to “Low” for write mode.
When 80XX interface mode is selected, this pin will be the Write (WR#) input. Data write operation is initiated when this pin is pulled low and the CS# is pulled low.
When serial mode is selected, this pin must be connected to VSS.
6 E/RD# I Read/Write Enable or Read
This pin is MCU interface input.
When interfacing to a 68XX-series microprocessor, this pin will be used as the Enable (E) signal. Read/write operation is initiated when this pin is pulled high and the CS# is pulled low.
When connecting to an 80XX-microprocessor, this pin receives the Read (RD#) signal. Data read operation is initiated when this pin is pulled low and CS# is pulled low.
When serial mode is selected, this pin must be connected to VSS.
7~14 DB0 I/O Host Data Input/Output Bus
These pins are 8-bit bi-directional data bus to be connected to the microprocessor’s data bus.
When serial mode is selected, D1 will be the serial data input SDIN and D0 will be the serial clock input SCLK.
DB1
DB2
DB3
DB4
DB5
DB6
DB7
15 NC P Reserved Pin
The N.C. pin between function pins are reserved for compatible and flexible design.
16 RES# I This pin is reset signal input.
When the pin is pulled LOW, initialization of the chip is executed.
Keep this pin pull HIGH during normal operation.
17 CS# I Data/Command Control
This pin is the chip select input connecting to the MCU. The chip is enabled for MCU communication only when CS# is pulled LOW.
18 NC P Reserved Pin
The N.C. pin between function pins are reserved for compatible and flexible design.
19 BS1 I Communicating Protocol Select
These pins are MCU interface selection input. See the following table:
BS[1:0] Interface
00 4 line SPI
01 3 line SPI
10 8-bit 8080 parallel
11 8-bit 6800 parallel

Note
(1) 0 is connected to VSS
(2) 1 is connected to VDD
20 BS0
21 TP_SCK I I2C clock input
22 TP_SDA I I2C data input and output
23 TP_INT I External interrupt to the host
24 TP_RST I External Reset, Low is active

Datos mecánicos

Elemento Valor estándar Unidad
Matriz de puntos 256 × 64 puntos
Dimensión del módulo 85.0 × 39.8 ×7.83 mm
zona activa 69.1 × 17.26 mm
Tamaño del punto 0.248 × 0.248 mm
Distancia entre puntos 0.27 × 0.27 mm
Modo de visualización Matriz Pasiva
Color de la pantalla Monocromos
Drive Duty 1/64 Duty
OLED IC SSD1322 (COF)
OLED Interfaz 6800, 8080, SPI
Tamaño (Diagonal) 2.8 pulgada
CTP IC FT6336U
Detect Point 1
CTP Interfaz I2C
Superficie Deslumbramiento

Valores nominales máximos absolutos

Valores nominales máximos absolutos

Parameter Símbolo Valor mín. Valor máx. Unidad
Supply Voltage for Display VDD -0.3 4 V
Temperatura de funcionamiento TOP -20 +70 °C
Temperatura de almacenamiento TSTG -30 +80 °C

Características electrónicas

DC Características electrónicas

Elemento Símbolo Condición Valor mín. Valor típico Valor máx. Unidad
Logic supply voltage VDD 2.8 3.0 3.3 V
High Level Input VIH 0.8×VDD VDD V
Low Level Input VIL 0 0.2×VDD V
High Level Output VOH 0.9×VDD VDD V
Low Level Output VOL 0 0.1×VDD V
50% Check Board operating Current VDD =3V 125 250 mA
 

Search keyword: 256x64 oled, oled 256x64, 2.8 oled, 2.8" oled, 2.8 pulgada oled, oled 2.8"

go top
close