Home Productos Pantalla OLED Pantalla táctil OLED WEP012864U-CTP

Modulos COG OLED 2.7 pulgada, 128x64 Con panel táctil capacitivo Frame +PCB

Modelo Nº WEP012864U-CTP

►Tipo : Gráfico
►Estructura : COG + marco + PCB
►Tamaño : 2.7 pulgada
►Matriz de puntos 128 x 64
►IC:SSD1357
►Fuente de alimentación de 3V
►1/64 duty
►Interfaz : 6800, 8080, SPI, I2C
►panel táctil : Con panel táctil capacitivo (CTP)
►Puntos táctiles : 1 Puntos
►Color de la pantalla: Blanco / Amarillo
►Compatibilidad con escala de grises

Descripción

WEP012864U-CTP es un módulo OLED gráfico COG con panel táctil capacitivo, con una resolución de 128x64 puntos y un área activa de 2,7 pulgadas (61,41 x 30,69 mm). El circuito integrado SSD1357 del módulo admite interfaces de 6800/8080 de 8 bits y SPI de 4 hilos, así como la interfaz I2C. La pantalla admite una escala de grises de 4 bits, con un voltaje lógico de 3V y un ciclo de trabajo de 1/64. El panel táctil capacitivo incluye el circuito integrado GT911, que admite una interfaz I2C con capacidad de toque de un punto.

La serie OLED WEP012864U-CTP cuenta con un marco metálico y una placa de circuito impreso que se conecta fácilmente a la aplicación mediante cables. Los clientes no necesitan desarrollar placas de circuito impreso adicionales por sí mismos. Integra ajustes de interfaz y circuitos VCC, lo que facilita su uso para los clientes. La placa de circuito impreso está diseñada con cuatro orificios roscados para facilitar la instalación del módulo en el producto de aplicación.

Este módulo OLED cuenta con una alta relación de contraste de 10000:1, lo que permite negros más vibrantes y profundos, así como blancos más brillantes. Esto se traduce en una calidad de imagen mejorada, detalles más nítidos y una legibilidad mejorada. El módulo puede funcionar en un rango de temperaturas de -20°C a 70°C, con temperaturas de almacenamiento que van desde -30°C a 80°C.

El WEP012864U con panel táctil CTP es muy adecuado para aplicaciones domóticas, equipos de alta tecnología, equipos de medición, sistemas de control industrial, instrumentos médicos, etc.

DIBUJO

WEP012864U-CTP
 

Data source ref: WEP012864UWPP3D00000

ESPECIFICACIONES

Función interfaz Pin

No. Símbolo Función
1 VSS This is a ground pin.
2 VDD Power supply pin for core logic operation
3 NC Reserved Pin
The N.C. pin between function pins is reserved for compatible and flexible design.
4 D/C# This pin is Data/Command control pin connecting to the MCU.
When the pin is pulled HIGH, the data at D[7:0] will be interpreted as data.
When the pin is pulled LOW, the data at D[7:0] will be transferred to a command register.
In I2C mode, this pin acts as SA0 for slave address selection.
When 3-wire serial interface is selected, this pin must be connected to VSS.
5 R/W#
(WR#)
This pin is read / write control input pin connecting to the MCU interface.
When 6800 interface mode is selected, this pin will be used as Read/Write (R/W#) selection input. Read mode will be carried out when this pin is pulled HIGH and write mode when LOW.
When 8080 interface mode is selected, this pin will be the Write (WR#) input. Data write operation is initiated when this pin is pulled LOW and the chip is selected.
When serial or I2C interface is selected, this pin must be connected to VSS.
6 E/RD# This pin is MCU interface input.
When 6800 interface mode is selected, this pin will be used as the Enable (E) signal.
Read/write operation is initiated when this pin is pulled HIGH and the chip is selected.
When 8080 interface mode is selected, this pin receives the Read (RD#) signal. Read operation is initiated when this pin is pulled LOW and the chip is selected.
When serial or I2C interface is selected, this pin must be connected to VSS.
7 DB0 These pins are bi-directional data bus connecting to the MCU data bus.
Unused pins are recommended to tie LOW.
When serial interface mode is selected, D0 will be the serial clock input: SCLK; D1 will be the serial data input: SDIN.
When I2C mode is selected, D2, D1 should be tied together and serve as SDAout, SDAin in application and D0 is the serial clock input, SCL.
8 DB1
9 DB2
10 DB3
11 DB4
12 DB5
13 DB6
14 DB7
15 NC No connection
16 RES# This pin is reset signal input.
When the pin is pulled LOW, initialization of the chip is executed.
Keep this pin pull HIGH during normal operation.
17 CS# Chip Select
This pin is the chip select input. The chip is enabled for MCU communication only when CS# is pulled low.
18 NC No connection
19 BS2 Communicating Protocol Select.
These pins are MCU interface selection input. See the following table:
  BS1 BS2
I2C 1 0
4-wire Serial 0 0
8-bit 8080 Parallel 1 1
8-bit 6800 Parallel 0 1
20 BS1
21 TP_SCK I2C clock signal
22 TP_SDA I2C data signal
23 TP_INT Interrupt signal, active low, asserted to request
Host start a new transaction
24 TP_RST External reset signal, active low

Datos mecánicos

Elemento Dimensión Unidad
Matriz de puntos 128 × 64
Dimensión del módulo 82.0 × 47.5 × 8.65 Max. mm
zona activa 61.41 × 30.69 mm
Tamaño del punto 0.45 × 0.45 mm
Distancia entre puntos 0.48 × 0.48 mm
Modo de visualización Matriz pasiva
Color de la pantalla Monocromos
Drive Duty 1/64 Duty
Escala de grises 4 bits
IC SSD1357
Interfaz 8-bits 6800 and 8080 parallel, 4-line SPI, I2C
Tamaño (Diagonal) 2.7 pulgada
 
CTP IC GT911
Puntos táctiles 1
CTP Interfaz I2C
Superficie Deslumbramiento

Valores nominales máximos absolutos

Parameter Symbol Min Max Unit
Supply Voltage for Logic VDD -0.3 4.0 V
Temperatura de funcionamiento TOP -20 +70 °C
Temperatura de almacenamiento TSTG -30 +80 °C

Características electrónicas

DC Características electrónicas

Elemento Símbolo Condición Valor mín. Valor típico Valor máx. Unidad
Supply Voltage for Logic VDD 2.8 3.0 3.3 V
High Level Input VIH 0.8×VDD V
Low Level Input VIL 0.2×VDD V
High Level Output VOH 0.9×VDD V
Low Level Output VOL 0.1×VDD V
50% Check Board operating Current IDD VDD =3V 160 240 mA

Search keyword: 128x64 oled, oled 128x64, 2.7 oled, 2.7 pulgada oled, oled 2.7"
go top
close