우리는 귀하의 프라이버시를 소중히 여깁니다
"모든 쿠키 허용"을 클릭하면 사이트 탐색을 개선하고, 사이트 사용을 분석하며, 마케팅 및 성능 노력에 도움을 주기 위해 쿠키를 귀하의 장치에 저장하는 데 동의한 것으로 간주됩니다. 이 주제에 대한 추가 정보는 당사의 정책에서 확인할 수 있습니다. 개인정보 보호정책
모델 번호 WEP012864U-CTP
►유형 : 그래픽
►구조 : COG + 프레임 + PCB
►크기 : 2.7 인치
►128 x 64 점 행렬
►IC:SSD1357
►3V 전원 공급 장치
►1/64 duty
►인터페이스 : 6800, 8080, SPI, I2C
►용량식 터치패널(스크린)이 있는(CTP)
►터치포인트 : 1 손가락
►디스플레이 색상: 백색 / 노란색
►지원 그레이스케일
WEP012864U-CTP는 해상도가 128x64 도트이며 2.7인치(61.41×30.69mm)의 유효 화면 영역을 갖춘 COG 그래픽 OLED 디스플레이로, 용량성 터치 패널이 내장되어 있습니다. 이 모듈에는 SSD1357 IC가 내장되어 있어 6800/8080 8비트 및 4선 SPI, I2C 인터페이스를 지원합니다. 이 디스플레이는 4비트 그레이스케일을 지원하며, 논리 전압은 3V이고 듀티 사이클은 1/64입니다. 용량성 터치 패널에는 내장 IC GT911가 내장되어 있으며 1점 터치 가능한 I2C 인터페이스를 지원합니다.
WEP012864U-CTP OLED 시리즈에는 와이어를 통해 애플리케이션에 쉽게 연결할 수 있는 금속 프레임과 PCB 보드가 함께 제공됩니다. 고객은 추가 PCB 보드를 별도로 개발할 필요가 없으며, 인터페이스 설정과 VCC 회로가 통합되어 고객이 사용하기 쉽도록 설계되었습니다. PCB에는 모듈을 애플리케이션 제품에 쉽게 설치할 수 있도록 4개의 나사 구멍이 디자인되어 있습니다.
이 OLED 모듈은 10,000:1의 높은 명암비를 자랑하며, 더 선명한 디스플레이 이미지를 제공합니다. 이를 통해 이미지 품질이 향상되고 더 선명한 디테일과 향상된 가독성을 얻을 수 있습니다. 이 모듈은 -20℃에서 70℃의 온도 범위에서 작동하며, 보관 온도는 -30℃에서 80℃ 사이입니다.
CTP 터치 패널을 갖춘 WEP012864U는 스마트 홈 응용 프로그램, 하이테크 장비, 미터 장비, 산업 제어 시스템, 의료 기기 등에 적합합니다.
Data source ref: WEP012864UWPP3D00000
항목 | 치수 | 단위 |
---|---|---|
도트 매트릭스 | 128 × 64 | - |
모듈 치수 | 82.0 × 47.5 × 8.65 Max. | mm |
활성 영역 | 61.41 × 30.69 | mm |
도트 크기 | 0.45 × 0.45 | mm |
도트 피치 | 0.48 × 0.48 | mm |
디스플레이 모드 | 패시브 매트릭스 (Passive Matrix) | |
디스플레이 색 | Monochrome | |
Drive Duty | 1/64 Duty | |
그레이스케일 | 4 bits | |
IC | SSD1357 | |
인터페이스 | 8-bits 6800 and 8080 parallel, 4-line SPI, I2C | |
크기 | 2.7 인치 |
CTP IC | GT911 |
터치포인트 | 1 |
CTP 인터페이스 | I2C |
표면 | 눈부심 |
Parameter | 기호 | 최소값 | 최대값 | 단위 |
---|---|---|---|---|
Supply Voltage for Logic | VDD | -0.3 | 4.0 | V |
작동 온도 | TOP | -20 | +70 | °C |
보관 온도 | TSTG | -30 | +80 | °C |
항목 | 기호 | 조건 | 최소값 | 대표값 | 최대값 | 단위 |
---|---|---|---|---|---|---|
Supply Voltage for Logic | VDD | - | 2.8 | 3.0 | 3.3 | V |
High Level Input | VIH | - | 0.8×VDD | - | - | V |
Low Level Input | VIL | - | - | - | 0.2×VDD | V |
High Level Output | VOH | - | 0.9×VDD | - | - | V |
Low Level Output | VOL | - | - | - | 0.1×VDD | V |
50% Check Board operating Current | IDD | VDD =3V | - | 160 | 240 | mA |
No. | 기호 | 기능 | |||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
1 | VSS | This is a ground pin. | |||||||||||||||
2 | VDD | Power supply pin for core logic operation | |||||||||||||||
3 | NC | Reserved Pin The N.C. pin between function pins is reserved for compatible and flexible design. |
|||||||||||||||
4 | D/C# | This pin is Data/Command control pin connecting to the MCU. When the pin is pulled HIGH, the data at D[7:0] will be interpreted as data. When the pin is pulled LOW, the data at D[7:0] will be transferred to a command register. In I2C mode, this pin acts as SA0 for slave address selection. When 3-wire serial interface is selected, this pin must be connected to VSS. |
|||||||||||||||
5 | R/W# (WR#) |
This pin is read / write control input pin connecting to the MCU interface. When 6800 interface mode is selected, this pin will be used as Read/Write (R/W#) selection input. Read mode will be carried out when this pin is pulled HIGH and write mode when LOW. When 8080 interface mode is selected, this pin will be the Write (WR#) input. Data write operation is initiated when this pin is pulled LOW and the chip is selected. When serial or I2C interface is selected, this pin must be connected to VSS. |
|||||||||||||||
6 | E/RD# | This pin is MCU interface input. When 6800 interface mode is selected, this pin will be used as the Enable (E) signal. Read/write operation is initiated when this pin is pulled HIGH and the chip is selected. When 8080 interface mode is selected, this pin receives the Read (RD#) signal. Read operation is initiated when this pin is pulled LOW and the chip is selected. When serial or I2C interface is selected, this pin must be connected to VSS. |
|||||||||||||||
7 | DB0 | These pins are bi-directional data bus connecting to the MCU data bus. Unused pins are recommended to tie LOW. When serial interface mode is selected, D0 will be the serial clock input: SCLK; D1 will be the serial data input: SDIN. When I2C mode is selected, D2, D1 should be tied together and serve as SDAout, SDAin in application and D0 is the serial clock input, SCL. |
|||||||||||||||
8 | DB1 | ||||||||||||||||
9 | DB2 | ||||||||||||||||
10 | DB3 | ||||||||||||||||
11 | DB4 | ||||||||||||||||
12 | DB5 | ||||||||||||||||
13 | DB6 | ||||||||||||||||
14 | DB7 | ||||||||||||||||
15 | NC | No connection | |||||||||||||||
16 | RES# | This pin is reset signal input. When the pin is pulled LOW, initialization of the chip is executed. Keep this pin pull HIGH during normal operation. |
|||||||||||||||
17 | CS# | Chip Select This pin is the chip select input. The chip is enabled for MCU communication only when CS# is pulled low. |
|||||||||||||||
18 | NC | No connection | |||||||||||||||
19 | BS2 | Communicating Protocol Select. These pins are MCU interface selection input. See the following table:
|
|||||||||||||||
20 | BS1 | ||||||||||||||||
21 | TP_SCK | I2C clock signal | |||||||||||||||
22 | TP_SDA | I2C data signal | |||||||||||||||
23 | TP_INT | Interrupt signal, active low, asserted to request Host start a new transaction |
|||||||||||||||
24 | TP_RST | External reset signal, active low |
"모든 쿠키 허용"을 클릭하면 사이트 탐색을 개선하고, 사이트 사용을 분석하며, 마케팅 및 성능 노력에 도움을 주기 위해 쿠키를 귀하의 장치에 저장하는 데 동의한 것으로 간주됩니다. 이 주제에 대한 추가 정보는 당사의 정책에서 확인할 수 있습니다. 개인정보 보호정책