제품 OLED 디스플레이 터치 OLED 디스플레이 WEN025664D-CTP

5.5인치 256x64 그래픽 COF OLED 디스플레이 모듈 +PCB +스루 홀 프레임

모델 번호 WEN025664D-CTP

►유형 : 그래픽
►구조 : COF+FR+PCB
►크기 : 5.5 인치
►256×64 점 행렬
►IC:SSD1322
►3V 전원 공급 장치
►1/64 duty cycle
►인터페이스 : 6800, 8080, SPI
►용량식 터치패널(스크린)이 있는(CTP)
►터치포인트 : 1 손가락
►디스플레이 색상: 백색 / 노란색 / 녹색
►지원 그레이스케일

설명

WEN025664D-CTP 모델은 프레임 베젤, PCB 및 전성 터치 스크린이 장착된 공업용 5.5인치 COF 그래픽 OLED입니다. 해상도는 256x64 도트로, 이 OLED 모듈은 SSD1322 IC가 내장되어 있으며 6800/8080 8비트 병렬 및 3선/4선 SPI 인터페이스를 지원하며 16(4비트) 단계의 회색 스케일을 지원합니다. 논리용 전압은 3V이며 50% 체커보드에서의 디스플레이 전류는 240mA @3.0V VDD (일반 값), 1/64 드라이빙 듀티입니다. 이 모델에는 모듈에 전성 터치 스크린이 있으며 I2C 인터페이스를 지원하는 GT911 IC가 내장되어 있습니다. CTP에 대한 하나의 감지 포인트, 일반 강광 표면 유리가 있습니다.

모듈에는 고객이 와이어 연결을 사용할 수 있는 PCB가 있습니다. 고객은 응용 프로그램에 대한 추가 PCB를 개발할 필요가 없습니다. 또한 고객이 사용하기 쉽도록 PCB에 VCC 회로를 통합했습니다. 이 모듈은 PIN, FFC, CN, FPC와 같은 여러 배선 방법을 지원합니다. PCB 보드에는 응용 프로그램에 모듈을 고정하는 쉬운 방법으로 네 개의 마운팅 홀이 있습니다.

이 OLED 모듈은 스마트 홈 응용 프로그램, 의료 기기, 산업 제어 등에 적합합니다. WEN025664D-CTP 모델은 -20°C에서 +70°C까지 동작할 수 있으며 저장 온도는 -30°C에서 +80°C까지입니다.

추가 OLED 패널 옵션은 다음과 같습니다:  

이 5.5인치 OLED 모듈은 특히 POS 시스템 및 자동 판매기와 같은 응용 프로그램에 적합합니다.

Winstar COF 시리즈는 다양하며, 벽/계량 장치, 가정용 응용 프로그램, POS 시스템, 클라우드/IoT 시스템, 휴대용 계기, 지능형 기술 장치, 에너지 시스템, 자동차, 통신 시스템, 의료 기기 등의 응용 프로그램을 지원합니다. 고객은 Winstar가 OLED 솔루션을 위한 다양한 도트 픽셀 형식을 제공하므로 현재의 STN 디스플레이에서 OLED 디스플레이로 업그레이드할 수 있는 유연성이 있습니다.

도면

5.5 inch 256x64 COF Touch OLED Display with PCB +Frame - WEN025664D-CTP

Data source ref:WEN025664DGPP3D00000

사양

인터페이스 핀 기능

Pin Number 기호 I/O 기능
1 VSS P Ground.
2 VDD P Power Supply for Core Logic Circuit
Power supply pin for core logic operation. A capacitor is required to connect between this pin and VSS
3 N.C. P Reserved Pin
The N.C. pin between function pins are reserved for compatible and flexible design.
4 D/C# I Data/Command Control
This pin is Data/Command control pin connecting to the MCU.
When the pin is pulled HIGH, the content at D[7:0] will be interpreted as data.
When the pin is pulled LOW, the content at D[7:0] will be interpreted as command.
5 R/W#
(WR#)
I Read/Write Select or Write
This pin is MCU interface input. When interfacing to a 68XX-series microprocessor, this pin will be used as Read/Write (R/W#) selection input. Pull this pin to “High” for read mode and pull it to “Low” for write mode.
When 80XX interface mode is selected, this pin will be the Write (WR#) input. Data write operation is initiated when this pin is pulled low and the CS# is pulled low.
When serial mode is selected, this pin must be connected to VSS.
6 E/RD# I Read/Write Enable or Read
This pin is MCU interface input. When interfacing to a 68XX-series microprocessor, this pin will be used as the Enable (E) signal. Read/write operation is initiated when this pin is pulled high and the CS# is pulled low.
When connecting to an 80XX-microprocessor, this pin receives the Read (RD#) signal. Data read operation is initiated when this pin is pulled low and CS# is pulled low.
When serial mode is selected, this pin must be connected to VSS.
7~14 DB0 I/O Host Data Input/Output Bus
These pins are 8-bit bi-directional data bus to be connected to the microprocessor’s data bus.
When serial mode is selected, D1 will be the serial data input SDIN and D0 will be the serial clock input SCLK.
DB1
DB2
DB3
DB4
DB5
DB6
DB7
15 NC P Reserved Pin
The N.C. pin between function pins are reserved for compatible and flexible design.
16 RES# I This pin is reset signal input.
When the pin is pulled LOW, initialization of the chip is executed.
Keep this pin pull HIGH during normal operation.
17 CS# I Data/Command Control
This pin is the chip select input connecting to the MCU. The chip is enabled for MCU communication only when CS# is pulled LOW.
18 NC P Reserved Pin
The N.C. pin between function pins are reserved for compatible and flexible design.
19 BS1 I Communicating Protocol Select
These pins are MCU interface selection input. See the following table:
BS[1:0] Bus Interface Selection
00 4 line SPI
01 3 line SPI
10 8-bit 8080 parallel
11 8-bit 6800 parallel
Note
(1) 0 is connected to VSS
(2) 1 is connected to VDD
20 BS0
21 TP_SCK I I2C clock input
22 TP_SDA I I2C data input and output
23 TP_INT I External interrupt to the host
24 TP_RST I External Reset, Low is active

기계적 데이터

항목 치수 단위
도트 매트릭스 256 x 64 Dots
모듈 치수 147.0 × 59 × 4.8 mm
활성 영역 135.65 × 33.89 mm
도트 크기 0.5 × 0.5 mm
도트 피치 0.53  × 0.53 mm
디스플레이 모드 패시브 매트릭스
디스플레이 색상 Monochrome
Drive Duty 1/64 Duty
그레이스케일 4 bits
OLED IC SSD1322
OLED 인터페이스 6800, 8080, SPI
크기 (대각선) 5,5 인치
 
CTP IC GT911
터치포인트 1
CTP 인터페이스 I2C
표면 눈부심

절대 최대 정격값

Parameter 기호 최소값 최대값 단위
Supply Voltage for Display VDD -0.3 4 V
작동 온도 TOP -20 +70 °C
보관 온도 TSTG -30 +80 °C

전기적 특성

DC 전기적 특성

항목 기호 조건 최소값 대표값 최대값 단위
Supply Voltage for Logic VDD 2.8 3.0 3.3 V
High Level Input VIH 0.8×VDD VDD V
Low Level Input VIL 0 0.2×VDD V
High Level Output VOH 0.9×VDD VDD V
Low Level Output VOL 0 0.1×VDD V
50% Check Board operating Current IDD VDD =3V 240 400 mA
 

Search keyword: 256x64 oled, oled 256x64, 5.5 oled, 5.5" oled, 5.5 인치 oled, oled 5.5"

go top
close