우리는 귀하의 프라이버시를 소중히 여깁니다
"모든 쿠키 허용"을 클릭하면 사이트 탐색을 개선하고, 사이트 사용을 분석하며, 마케팅 및 성능 노력에 도움을 주기 위해 쿠키를 귀하의 장치에 저장하는 데 동의한 것으로 간주됩니다. 이 주제에 대한 추가 정보는 당사의 정책에서 확인할 수 있습니다. 개인정보 보호정책
모델 번호 WEN025664D
►유형 : 그래픽
►구조 : COF+Frame+PCB
►크기 : 5.5 인치
►256x64 점 행렬
►IC:SSD1322
►3V 전원 공급 장치
►1/64 duty
►인터페이스 : 6800, 8080, SPI
►디스플레이 색상: 백색 / 노란색 / 녹색
►지원 그레이스케일
WEN025664D COF OLED 디스플레이 모듈은 프레임과 PCB를 포함하며, 256x64 도트의 해상도와 5.5인치 대각 모듈 크기(135.65 × 33.89 mm)를 자랑합니다. 내장된 SSD1322 IC는 6800/8080 8비트 및 3/4라인 SPI 인터페이스를 지원하며, 3V 전원 공급을 사용하며, 1/64 듀티 구동 방법을 활용하며, 인상적인 대비 비율 10000:1로 4비트 그레이스케일을 지원합니다.
이 OLED 시리즈에는 프레임이 있는 PCB 보드가 함께 제공되어 와이어를 통한 응용 프로그램과의 편리한 연결을 용이하게 합니다. 모듈은 사용자 친화적인 작업을 위해 인터페이스 설정 및 VDD 회로를 통합하므로 고객은 추가 PCB 보드를 개발할 필요가 없습니다. PCB에는 응용 프로그램 제품에의 간편한 설치를 용이하게 하는 네 개의 나사 구멍이 포함되어 있습니다. -40℃에서 +80℃의 운영 온도 범위 및 -40℃에서 +85℃의 저장 온도 범위로, 이 OLED 모듈은 다양한 환경에 적합합니다.
추가 OLED 패널 옵션은 다음과 같습니다:이 5.5인치 OLED 모듈은 특히 POS 시스템 및 자동 판매기와 같은 응용 프로그램에 적합합니다.
Winstar COF 시리즈는 다양하며, 벽/계량 장치, 가정용 응용 프로그램, POS 시스템, 클라우드/IoT 시스템, 휴대용 계기, 지능형 기술 장치, 에너지 시스템, 자동차, 통신 시스템, 의료 기기 등의 응용 프로그램을 지원합니다. 고객은 Winstar가 OLED 솔루션을 위한 다양한 도트 픽셀 형식을 제공하므로 현재의 STN 디스플레이에서 OLED 디스플레이로 업그레이드할 수 있는 유연성이 있습니다.
항목 | 치수 | 단위 |
---|---|---|
도트 매트릭스 | 256 × 64 Dots | - |
모듈 치수 | 147.0 × 59 × 2.5 | mm |
활성 영역 | 135.65 × 33.89 | mm |
도트 크기 | 0.50 × 0.50 | mm |
도트 피치 | 0.53 × 0.53 | mm |
디스플레이 모드 | Passive Matrix | |
디스플레이 색상 | Monochrome | |
Drive Duty | 1/64 Duty | |
Gray Scale | 4 bits | |
IC | SSD1322 | |
인터페이스 | 6800, 8080, SPI | |
크기 | 5.5 inch |
Parameter | 기호 | 최소값 | 최대값 | 단위 |
---|---|---|---|---|
Supply Voltage for Display | VDD | -0.3 | 4 | V |
작동 온도 | TOP | -40 | +80 | °C |
보관 온도 | TSTG | -40 | +85 | °C |
항목 | 기호 | 조건 | 최소값 | 대표값 | 최대값 | 단위 |
---|---|---|---|---|---|---|
Supply Voltage for Logic | VDD | - | 2.8 | 3.0 | 3.3 | V |
High Level Input | VIH | - | 0.8×VDD | - | VDD | V |
Low Level Input | VIL | - | 0 | - | 0.2×VDD | V |
High Level Output | VOH | - | 0.9×VDD | - | VDD | V |
Low Level Output | VOL | - | 0 | - | 0.1×VDD | V |
Display 50% Pixel on | IDD | VDD =3V | - | 240 | 400 | mA |
Pin Number |
기호 | I/O | 기능 | ||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|
1 | VSS | P | Ground. | ||||||||||
2 | VDD | P | Power Supply for Core Logic Circuit Power supply pin for core logic operation. A capacitor is required to connect between this pin and VSS |
||||||||||
3 | N.C. | P | Reserved Pin The N.C. pin between function pins are reserved for compatible and flexible design. |
||||||||||
4 | D/C# | I | Data/Command Control This pin is Data/Command control pin connecting to the MCU. When the pin is pulled HIGH, the content at D[7:0] will be interpreted as data. When the pin is pulled LOW, the content at D[7:0] will be interpreted as command. |
||||||||||
5 | R/W# (WR#) |
I | Read/Write Select or Write This pin is MCU interface input. When interfacing to a 68XX-series microprocessor, this pin will be used as Read/Write (R/W#) selection input. Pull this pin to “High” for read mode and pull it to “Low” for write mode. When 80XX interface mode is selected, this pin will be the Write (WR#) input. Data write operation is initiated when this pin is pulled low and the CS# is pulled low. When serial mode is selected, this pin must be connected to VSS. |
||||||||||
6 | E(/RD#) | I | Read/Write Enable or Read This pin is MCU interface input. When interfacing to a 68XX-series microprocessor, this pin will be used as the Enable (E) signal. Read/write operation is initiated when this pin is pulled high and the CS# is pulled low. When connecting to an 80XX-microprocessor, this pin receives the Read (RD#) signal. Data read operation is initiated when this pin is pulled low and CS# is pulled low. When serial mode is selected, this pin must be connected to VSS. |
||||||||||
7~14 | DB0 | I/O | Host Data Input/Output Bus These pins are 8-bit bi-directional data bus to be connected to the microprocessor’s data bus. When serial mode is selected, D1 will be the serial data input SDIN and D0 will be the serial clock input SCLK. |
||||||||||
DB1 | |||||||||||||
DB2 | |||||||||||||
DB3 | |||||||||||||
DB4 | |||||||||||||
DB5 | |||||||||||||
DB6 | |||||||||||||
DB7 | |||||||||||||
15 | NC | P | Reserved Pin The N.C. pin between function pins are reserved for compatible and flexible design. |
||||||||||
16 | RES# | I | This pin is reset signal input. When the pin is pulled LOW, initialization of the chip is executed. Keep this pin pull HIGH during normal operation. |
||||||||||
17 | CS# | I | Data/Command Control This pin is the chip select input connecting to the MCU. The chip is enabled for MCU communication only when CS# is pulled LOW. |
||||||||||
18 | NC | P | Reserved Pin The N.C. pin between function pins are reserved for compatible and flexible design. |
||||||||||
19 | BS1 | I | Communicating Protocol Select These pins are MCU interface selection input. See the following table:
(1) 0 is connected to VSS (2) 1 is connected to VDD |
||||||||||
20 | BS0 | ||||||||||||
21 | NC | - | No connection | ||||||||||
22 | NC | - | No connection | ||||||||||
23 | NC | - | No connection | ||||||||||
24 | NC | - | No connection |
"모든 쿠키 허용"을 클릭하면 사이트 탐색을 개선하고, 사이트 사용을 분석하며, 마케팅 및 성능 노력에 도움을 주기 위해 쿠키를 귀하의 장치에 저장하는 데 동의한 것으로 간주됩니다. 이 주제에 대한 추가 정보는 당사의 정책에서 확인할 수 있습니다. 개인정보 보호정책