제품 OLED 디스플레이 터치 OLED 디스플레이 WEN025664A-CTP

2.8인치 256x64 해상도 그레이스케일 COF OLED 디스플레이, 터치 패널, PCB 및 프레임 지원

모델 번호 WEN025664A-CTP

►유형 : 그래픽
►구조 : COF + 프레임 + PCB
►크기 : 2.8 인치
►256×64 점 행렬
►IC:SSD1322
►3V 전원 공급 장치
►1/64 duty cycle
►인터페이스 : 6800, 8080, SPI
►용량식 터치패널(스크린)이 있는(CTP)
►터치포인트 : 1 손가락
►디스플레이 색상: 백색 / 노란색
►지원 그레이스케일

설명

WEN025664A-CTP 시리즈는 2.8인치 단색 그래픽 COF OLED 디스플레이로, 256x64 도트의 정전용량 터치 패널이 탑재되어 있습니다. SSD1322 IC가 장착되어 있으며, 6800/8080 8비트 및 3/4와이어 SPI 인터페이스를 포함한 다양한 인터페이스를 지원합니다. WEN025664A-CTP의 모듈 크기는 85.0 × 39.8 mm이며, 활성 영역은 69.1 × 17.26 mm입니다. 이 모델은 FT6336U IC를 사용한 프로젝티드 커패시티브 터치 패널 (PCAP)을 채택하며 I2C 인터페이스 및 1점 터치를 지원합니다.

WEN025664A-CTP OLED 시리즈는 3V 전원 공급을 기반으로 하며 1/64 듀티의 구동 방식을 채택합니다. 그레이 스케일을 지원하며 10,000:1의 높은 대비 비율을 자랑합니다. 모듈은 -20°C에서 +70°C까지의 온도 범위에서 작동할 수 있으며 저장 온도 범위는 -30°C에서 +80°C까지입니다.

금속 프레임, PCB 보드 및 4개의 나사 구멍을 갖춘 WEN025664A-CTP는 고객이 쉽게 설치할 수 있도록 도와줍니다. PCB 보드가 장착된 OLED 시리즈는 고객이 와이어를 사용하여 쉽게 응용 프로그램에 연결될 수 있어 고객이 추가 PCB 보드를 개발할 필요가 없습니다. 인터페이스 설정 및 VDD 회로의 통합은 사용자 편의성을 향상시킵니다. 또한 PCB 상에 있는 4개의 나사 구멍은 응용 프로그램 제품에 모듈을 쉽게 설치할 수 있도록 돕습니다.

WEN025664A-CTP는 터치 패널이 없는 동일한 OLED 패널을 제공하는 옵션도 있습니다. 터치 패널이 없는 옵션을 원하시면 WEN025664A 모델을 선택해주세요.

도면

2.8 inch 256x64 OLED Display with Touch Panel Support Grayscale - WEN025664A-CTP

Data source ref: WEN025664AWPP3D00000

사양

인터페이스 핀 기능

Pin Number 기호 I/O 기능
1 VSS P Ground.
2 VDD P Power Supply for Core Logic Circuit
Power supply pin for core logic operation. A capacitor is required to connect between this pin and VSS
3 N.C. P Reserved Pin
The N.C. pin between function pins are reserved for compatible and flexible design.
4 D/C# I Data/Command Control
This pin is Data/Command control pin connecting to the MCU.
When the pin is pulled HIGH, the content at D[7:0] will be interpreted as data.
When the pin is pulled LOW, the content at D[7:0] will be interpreted as command.
5 R/W#
(WR#)
I Read/Write Select or Write
This pin is MCU interface input. When interfacing to a 68XX-series microprocessor, this pin will be used as Read/Write (R/W#) selection input. Pull this pin to “High” for read mode and pull it to “Low” for write mode.
When 80XX interface mode is selected, this pin will be the Write (WR#) input. Data write operation is initiated when this pin is pulled low and the CS# is pulled low.
When serial mode is selected, this pin must be connected to VSS.
6 E/RD# I Read/Write Enable or Read
This pin is MCU interface input.
When interfacing to a 68XX-series microprocessor, this pin will be used as the Enable (E) signal. Read/write operation is initiated when this pin is pulled high and the CS# is pulled low.
When connecting to an 80XX-microprocessor, this pin receives the Read (RD#) signal. Data read operation is initiated when this pin is pulled low and CS# is pulled low.
When serial mode is selected, this pin must be connected to VSS.
7~14 DB0 I/O Host Data Input/Output Bus
These pins are 8-bit bi-directional data bus to be connected to the microprocessor’s data bus.
When serial mode is selected, D1 will be the serial data input SDIN and D0 will be the serial clock input SCLK.
DB1
DB2
DB3
DB4
DB5
DB6
DB7
15 NC P Reserved Pin
The N.C. pin between function pins are reserved for compatible and flexible design.
16 RES# I This pin is reset signal input.
When the pin is pulled LOW, initialization of the chip is executed.
Keep this pin pull HIGH during normal operation.
17 CS# I Data/Command Control
This pin is the chip select input connecting to the MCU. The chip is enabled for MCU communication only when CS# is pulled LOW.
18 NC P Reserved Pin
The N.C. pin between function pins are reserved for compatible and flexible design.
19 BS1 I Communicating Protocol Select
These pins are MCU interface selection input. See the following table:
BS[1:0] Interface
00 4 line SPI
01 3 line SPI
10 8-bit 8080 parallel
11 8-bit 6800 parallel

Note
(1) 0 is connected to VSS
(2) 1 is connected to VDD
20 BS0
21 TP_SCK I I2C clock input
22 TP_SDA I I2C data input and output
23 TP_INT I External interrupt to the host
24 TP_RST I External Reset, Low is active

기계적 데이터

항목 치수 단위
도트 매트릭스 256 × 64 Dots
모듈 치수 85.0 × 39.8 ×7.83 mm
활성 영역 69.1 × 17.26 mm
도트 크기 0.248×0.248 mm
도트 피치 0.27×0.27 mm
디스플레이 모드 패시브 매트릭스
디스플레이 색상 Monochrome
Drive Duty 1/64 Duty
OLED IC SSD1322 (COF)
OLED 인터페이스 6800, 8080, SPI
크기 (대각선) 2.8 인치
CTP IC FT6336U
터치포인트 1
CTP 인터페이스 I2C
표면 눈부심

절대 최대 정격값

절대 최대 정격값

Parameter 기호 최소값 최대값 단위
Supply Voltage for Display VDD -0.3 4 V
작동 온도 TOP -20 +70 °C
보관 온도 TSTG -30 +80 °C

전기적 특성

DC 전기적 특성

항목 기호 조건 최소값 대표값 최대값 단위
Supply Voltage for Logic VDD 2.8 3.0 3.3 V
High Level Input VIH 0.8×VDD VDD V
Low Level Input VIL 0 0.2×VDD V
High Level Output VOH 0.9×VDD VDD V
Low Level Output VOL 0 0.1×VDD V
50% Check Board operating Current IDD VDD =3V 125 250 mA
 

Search keyword: 256x64 oled, oled 256x64, 2.8 oled, 2.8" oled, 2.8 인치 oled, oled 2.8"

go top
close