Home Productos Pantalla OLED Pantalla táctil OLED WEP012864Q-CTP

Modulos COG OLED 2.7 pulgada, 128x64 Con panel táctil capacitivo Frame +PCB

Modelo Nº WEP012864Q-CTP

►Tipo : Gráfico
►Estructura : COG+FR+PCB
►Tamaño : 2.7 pulgada
►Matriz de puntos 128 x 64
►Controlador integrado SSD1309
►Fuente de alimentación de 3V
►1/64 duty
►Interfaz : 6800, 8080, SPI, I2C
►panel táctil : Con panel táctil capacitivo (CTP)
►Puntos táctiles : 1 Puntos
►Color de la pantalla: Blanco / Amarillo / Azul cielo / Verde

DIBUJO

2.7 inch 128x64 COG Capacitive Touch OLED Display with Frame +PCB - WEP012864Q-CTP
 

Data source ref: WEP012864QWPP3D00000

ESPECIFICACIONES

Función interfaz Pin

No. Símbolo Función
1 VSS Ground.
2 VDD Power supply pin for core logic operation
3 NC No connection
4 D/C# This pin is Data/Command control pin connecting to the MCU.
When the pin is pulled HIGH, the data at D[7:0] will be interpreted as data.
When the pin is pulled LOW, the data at D[7:0] will be transferred to a command register.
In I2C mode, this pin acts as SA0 for slave address selection.
5 R/W#
(WR#)
This pin is read / write control input pin connecting to the MCU interface.
When 6800 interface mode is selected, this pin will be used as Read/Write (R/W#) selection input. Read mode will be carried out when this pin is pulled HIGH and write mode when LOW.
When 8080 interface mode is selected, this pin will be the Write (WR#) input. Data write operation is initiated when this pin is pulled LOW and the chip is selected.
When serial or I2C interface is selected, this pin must be connected to VSS.
6 E(/RD#) This pin is MCU interface input.
When 6800 interface mode is selected, this pin will be used as the Enable (E) signal.
Read/write operation is initiated when this pin is pulled HIGH and the chip is selected.
When 8080 interface mode is selected, this pin receives the Read (RD#) signal. Read operation is initiated when this pin is pulled LOW and the chip is selected.
When serial or I2C interface is selected, this pin must be connected to VSS.
7-14 D0~D7 These pins are bi-directional data bus connecting to the MCU data bus.
Unused pins are recommended to tie LOW.
When serial interface mode is selected, D0 will be the serial clock input: SCLK; D1 will be the serial data input: SDIN and D2 should be kept NC.
When I2C mode is selected, D2, D1 should be tied together and serve as SDAout, SDAin in application and D0 is the serial clock input, SCL.
15 NC No connection
16 RES# This pin is reset signal input.
When the pin is pulled LOW, initialization of the chip is executed.
Keep this pin pull HIGH during normal operation.
17 CS# This pin is the chip select input connecting to the MCU.
The chip is enabled for MCU communication only when CS# is pulled LOW (active LOW).
18 NC No connection
19 BS2 MCU bus interface selection pins. Select appropriate logic setting as described in the following table. BS2 and BS1 are pin select
  BS1 BS2
I2C 1 0
4-wire Serial 0 0
8-bit 68xx Parallel 0 1
8-bit 80xx Parallel 1 1
Note
(1) 0 is connected to VSS
(2) 1 is connected to VDD
20 BS1
21 TP_SCK I2C clock signal
22 TP_SDA I2C data signal
23 TP_INT External interrupt signal, active low
24 TP_RST External reset signal, active low

Datos mecánicos

Elemento Dimensión Unidad
Matriz de puntos 128 × 64
Dimensión del módulo 82.0 × 47.5 × 8.65 Max. mm
zona activa 61.41 × 30.69 mm
Tamaño del punto 0.45 × 0.45 mm
Distancia entre puntos 0.48 × 0.48 mm
Modo de visualización Matriz pasiva
Color de la pantalla Monocromos
Drive Duty 1/64 Duty
IC SSD1309
Interfaz 6800,8080,4-Wire SPI,I2C
Tamaño (Diagonal) 2.7 pulgada
CTP IC GT911
Puntos táctiles 1
CTP Interfaz I2C
Superficie Deslumbramiento

Valores nominales máximos absolutos

Parameter Symbol Min Max Unit
Supply Voltage for Logic VDD -0.3 4 V
Temperatura de funcionamiento TOP -20 +70 °C
Temperatura de almacenamiento TSTG -30 +80 °C

Características electrónicas

DC Características electrónicas

Elemento Símbolo Condición Valor mín. Valor típico Valor máx. Unidad
Supply Voltage for Logic VDD 2.8 3.0 3.3 V
High Level Input VIH 0.8×VDD V
Low Level Input VIL 0.2×VDD V
High Level Output VOH 0.9×VDD V
Low Level Output VOL 0.1×VDD V
50% Check Board operating Current VDD =3V 175 350 mA
 

Touch Panel Controller GT911

Elemento Símbolo Valor mín. Valor típico Valor máx. Unidad
Input High Volt. VIH 0.75xVDD   VDD+0.3 V
Input Low Volt. VIL -0.3 0.25xVDD V
Output High Volt. VOH 0.85xVDD V
Output Low Volt. VOL 0.15xVDD V

Search keyword: 128x64 oled, oled 128x64, 2.7 oled, 2.7 pulgada oled, oled 2.7
go top
close