Home Produtos Display OLED Display OLED Tátil WEP012864Q-CTP

Display OLED 128x64 de 2,7 polegadas com Painel Tátil Capacitivo

Model No. WEP012864Q-CTP

►Tipo: Gráfico
►Estrutura: COG + marco + PCB
►Tamanho: 2,7 polegadas
►Matriz de pontos 128 x 64
►IC:SSD1309
►Alimentação 3V
►1/64 duty
►Interface: 6800, 8080, SPI, I2C
►Tela de Toque: Com painel de toque capacitivo (CTP)
►Detect Point : 1 Finger
►Display Color: Branco / Amarelo / Céu azul / Verde

Descrição

O modelo WEP012864Q-CTP é um display OLED gráfico COG com Painel de Toque Capacitivo, de 2,7 polegadas, com uma resolução de 128x64 pixels. Este módulo OLED é integrado com o circuito integrado SSD1309; suporta interfaces paralelas 6800/8080 de 8 bits, I2C e 4-Wire SPI, a tensão de alimentação para a lógica é de 3V, a corrente de exibição com 50% de verificação é de 175mA @ 3.0V VDD (valor típico), o dever de condução é de 1/64. Este modelo tem um Painel de Toque Capacitivo no módulo; é integrado com o circuito integrado GT911 que suporta a interface I2C, um ponto de detecção para CTP e uma superfície de vidro normal e brilhante. O módulo tem uma placa de circuito impresso no módulo, o que permite aos clientes usar uma conexão com fio sem a necessidade de desenvolver PCBs extras para suas aplicações. Além disso, integramos um circuito VCC no PCB para facilitar o uso pelos clientes.

O modelo WEP012864Q-CTP é um display OLED COG com um PCB no módulo. Este PCB com quatro furos de montagem é um método simples para os clientes fixarem os módulos em suas aplicações. Este módulo OLED é adequado para aplicativos de casa inteligente, dispositivos médicos, controle industrial, etc. O modelo WEP012864Q-CTP pode operar em temperaturas de -20℃ a +70℃; sua faixa de temperaturas de armazenamento varia de -30℃ a +80℃.

DRAWING

2.7 inch 128x64 COG Capacitive Touch OLED Display with Frame +PCB - WEP012864Q-CTP
 

Data source ref: WEP012864QWPP3D00000

SPECIFICATIONS

Função do pino de interface

No. Símbolo Função
1 VSS Ground.
2 VDD Power supply pin for core logic operation
3 NC No connection
4 D/C# This pin is Data/Command control pin connecting to the MCU.
When the pin is pulled HIGH, the data at D[7:0] will be interpreted as data.
When the pin is pulled LOW, the data at D[7:0] will be transferred to a command register.
In I2C mode, this pin acts as SA0 for slave address selection.
5 R/W#
(WR#)
This pin is read / write control input pin connecting to the MCU interface.
When 6800 interface mode is selected, this pin will be used as Read/Write (R/W#) selection input. Read mode will be carried out when this pin is pulled HIGH and write mode when LOW.
When 8080 interface mode is selected, this pin will be the Write (WR#) input. Data write operation is initiated when this pin is pulled LOW and the chip is selected.
When serial or I2C interface is selected, this pin must be connected to VSS.
6 E(/RD#) This pin is MCU interface input.
When 6800 interface mode is selected, this pin will be used as the Enable (E) signal.
Read/write operation is initiated when this pin is pulled HIGH and the chip is selected.
When 8080 interface mode is selected, this pin receives the Read (RD#) signal. Read operation is initiated when this pin is pulled LOW and the chip is selected.
When serial or I2C interface is selected, this pin must be connected to VSS.
7-14 D0~D7 These pins are bi-directional data bus connecting to the MCU data bus.
Unused pins are recommended to tie LOW.
When serial interface mode is selected, D0 will be the serial clock input: SCLK; D1 will be the serial data input: SDIN and D2 should be kept NC.
When I2C mode is selected, D2, D1 should be tied together and serve as SDAout, SDAin in application and D0 is the serial clock input, SCL.
15 NC No connection
16 RES# This pin is reset signal input.
When the pin is pulled LOW, initialization of the chip is executed.
Keep this pin pull HIGH during normal operation.
17 CS# This pin is the chip select input connecting to the MCU.
The chip is enabled for MCU communication only when CS# is pulled LOW (active LOW).
18 NC No connection
19 BS2 MCU bus interface selection pins. Select appropriate logic setting as described in the following table. BS2 and BS1 are pin select
  BS1 BS2
I2C 1 0
4-wire Serial 0 0
8-bit 68xx Parallel 0 1
8-bit 80xx Parallel 1 1
Note
(1) 0 is connected to VSS
(2) 1 is connected to VDD
20 BS1
21 TP_SCK I2C clock signal
22 TP_SDA I2C data signal
23 TP_INT External interrupt signal, active low
24 TP_RST External reset signal, active low

Dados Mecânicos

Item Dimensão Unidade
Matriz de pontos 128 x 64
Dimensão do módulo 82.0 × 47.5 × 8.65 Max. mm
Área ativa 61.41 × 30.69 mm
Tamanho do ponto 0.45 × 0.45 mm
Distância entre pontos 0.48 × 0.48 mm
Modo de exibição Passive Matrix
Cor de exibição Monochrome
Drive Duty 1/64 Duty
IC SSD1309
Interface 6800,8080,4-Wire SPI,I2C
Tamanho 2,7 polegadas
CTP IC GT911
Detect Point 1
CTP Interface I2C
Superfície Reflexo

Classificações Máximas Absolutas

Parameter Símbolo Valor Min Valor Máximo Unidade
Supply Voltage for Logic VDD -0.3 4 V
Temperatura de operação TOP -20 +70 °C
Temperatura de armazenamento TSTG -30 +80 °C
 

Características Eletrônicas

DC Características Eletrônicas

Item Símbolo Condição Valor Min Valor Típico Valor Máximo Unidade
Supply Voltage for Logic VDD 2.8 3.0 3.3 V
High Level Input VIH 0.8×VDD V
Low Level Input VIL 0.2×VDD V
High Level Output VOH 0.9×VDD V
Low Level Output VOL 0.1×VDD V
50% Check Board operating Current VDD =3V 175 350 mA
 

Touch Panel Controller GT911

Item Símbolo Valor Min Valor Típico Valor Máximo Unidade
Input High Volt. VIH 0.75xVDD   VDD+0.3 V
Input Low Volt. VIL -0.3 0.25xVDD V
Output High Volt. VOH 0.85xVDD V
Output Low Volt. VOL 0.15xVDD V
go top
close