Home Prodotti Display OLED Display touch OLED WEP012864Q-CTP

Moduli Display OLED COG 128x64, 2.7" con pannello touch capacitivo + Frame +PCB

Modello numero WEP012864Q-CTP

►Tipo: grafico
►Struttura: COG + cornice + PCB
►Dimensione: 2.7 pollici
►128 x 64 a matrice di punti
►IC:SSD1309
►Alimentatore 3V
►1/64 duty
►Interfaccia: 6800, 8080, SPI, I2C
►Touch Screen: con pannello touch capacitivo (CTP)
►Punti di tocco : 1 Dito
►Colore display: Bianco / Giallo / Cielo blu / Verde

Descrizione

Il modello WEP012864Q-CTP è un display OLED grafico COG con pannello tattile capacitivo, con dimensioni diagonal 2,7 pollici, composto da 128x64 pixel. Questo modulo OLED è integrato con SSD1309 IC; supporta le interfacce parallele 6800/8080 a 8 bit, I2C e 4-Wire SPI, la tensione di alimentazione per la logica è 3V, la corrente della scheda di controllo al 50% è 175mA @ 3,0V VDD (valore tipico), ciclo di guida 1/64. Questo modello ha un pannello tattile capacitivo sul modulo; è integrato con IC GT911 che supporta l'interfaccia I2C, un punto di rilevamento per il pannello tattile capacitivo, vetro superficiale normale con riflessione. Il modulo ha una scheda PCB sul modulo che è adatta per i clienti per l'uso della connessione a filo; i clienti non devono sviluppare ulteriori PCB per le proprie applicazioni. Inoltre, abbiamo integrato il circuito VCC sulla PCB per rendere più facile l'uso da parte dei clienti.

Il modello WEP012864Q-CTP è un display OLED COG con una PCB sul modulo. Questa scheda PCB con quattro fori di montaggio è un metodo semplice per i clienti per fissare i moduli sulle proprie applicazioni. Questo modulo OLED è adatto per applicazioni smart home, dispositivi medici, controllo industriale, ecc. Il modello WEP012864Q-CTP può funzionare a temperature da -20℃ a +70℃; le temperature di stoccaggio variano da -30℃ a +80℃.

DISEGNO

2.7 inch 128x64 COG Capacitive Touch OLED Display with Frame +PCB - WEP012864Q-CTP
 

Data source ref: WEP012864QWPP3D00000

SPECIFICHE TECNICHE

Funzione dei Pin di Interfaccia

No. Simbolo Funzione
1 VSS Ground.
2 VDD Power supply pin for core logic operation
3 NC No connection
4 D/C# This pin is Data/Command control pin connecting to the MCU.
When the pin is pulled HIGH, the data at D[7:0] will be interpreted as data.
When the pin is pulled LOW, the data at D[7:0] will be transferred to a command register.
In I2C mode, this pin acts as SA0 for slave address selection.
5 R/W#
(WR#)
This pin is read / write control input pin connecting to the MCU interface.
When 6800 interface mode is selected, this pin will be used as Read/Write (R/W#) selection input. Read mode will be carried out when this pin is pulled HIGH and write mode when LOW.
When 8080 interface mode is selected, this pin will be the Write (WR#) input. Data write operation is initiated when this pin is pulled LOW and the chip is selected.
When serial or I2C interface is selected, this pin must be connected to VSS.
6 E(/RD#) This pin is MCU interface input.
When 6800 interface mode is selected, this pin will be used as the Enable (E) signal.
Read/write operation is initiated when this pin is pulled HIGH and the chip is selected.
When 8080 interface mode is selected, this pin receives the Read (RD#) signal. Read operation is initiated when this pin is pulled LOW and the chip is selected.
When serial or I2C interface is selected, this pin must be connected to VSS.
7-14 D0~D7 These pins are bi-directional data bus connecting to the MCU data bus.
Unused pins are recommended to tie LOW.
When serial interface mode is selected, D0 will be the serial clock input: SCLK; D1 will be the serial data input: SDIN and D2 should be kept NC.
When I2C mode is selected, D2, D1 should be tied together and serve as SDAout, SDAin in application and D0 is the serial clock input, SCL.
15 NC No connection
16 RES# This pin is reset signal input.
When the pin is pulled LOW, initialization of the chip is executed.
Keep this pin pull HIGH during normal operation.
17 CS# This pin is the chip select input connecting to the MCU.
The chip is enabled for MCU communication only when CS# is pulled LOW (active LOW).
18 NC No connection
19 BS2 MCU bus interface selection pins. Select appropriate logic setting as described in the following table. BS2 and BS1 are pin select
  BS1 BS2
I2C 1 0
4-wire Serial 0 0
8-bit 68xx Parallel 0 1
8-bit 80xx Parallel 1 1
Note
(1) 0 is connected to VSS
(2) 1 is connected to VDD
20 BS1
21 TP_SCK I2C clock signal
22 TP_SDA I2C data signal
23 TP_INT External interrupt signal, active low
24 TP_RST External reset signal, active low

Dati meccanici

Articolo Dimensioni Unità
A matrice di punti 128 x 64
Dimensione del modulo 82.0 × 47.5 × 8.65 Max. mm
Area attiva 61.41 × 30.69 mm
Dimensioni del Dot 0.45 × 0.45 mm
Passo del Dot 0.48 × 0.48 mm
Modalità display Matrice passiva
Colore display Monocromatici
Drive Duty 1/64 Duty
IC SSD1309
Interfaccia 6800,8080,4-Wire SPI,I2C
Diagonale 2.7 pollici
CTP IC GT911
Punti di tocco 1
CTP Interfaccia I2C
Superficie Bagliore (Glare)

Valori massimi assoluti

Parameter Simbolo Valore Min Valore massimo Unità
Supply Voltage for Logic VDD -0.3 4 V
Temperatura di lavoro TOP -20 +70 °C
Temperatura di stock TSTG -30 +80 °C

Caratteristiche elettriche

DC Caratteristiche elettriche

Articolo Simbolo Condizione Valore Min Valore tipico Valore massimo Unità
Supply Voltage for Logic VDD 2.8 3.0 3.3 V
High Level Input VIH 0.8×VDD V
Low Level Input VIL 0.2×VDD V
High Level Output VOH 0.9×VDD V
Low Level Output VOL 0.1×VDD V
50% Check Board operating Current VDD =3V 175 350 mA
 

Touch Panel Controller GT911

Articolo Simbolo Valore Min Valore tipico Valore massimo Unità
Input High Volt. VIH 0.75xVDD   VDD+0.3 V
Input Low Volt. VIL -0.3 0.25xVDD V
Output High Volt. VOH 0.85xVDD V
Output Low Volt. VOL 0.15xVDD V
 
Search keyword: 128x64 oled, oled 128x64, 2.7 oled, 2.7 pollici oled, oled 2.7
go top
close