Home محصولات ماژول OLED گرافیک OLED WEO012864D-Hotbar

مدل شماره WEO012864D-Hotbar

◄نوع: گرافیک (بدون فریم)
◄ساختار: COG + Hotbar FPC
◄سایز: 0.96 اینچ
◄ماتریس نقطه ای 128*64
◄کنترلگر SSD1306BZ
◄منبع انرژی +3V
◄کار 1/64
◄رابط: 6800/8080/SPI/I2C

شرح

Left: Thinner version without sponge
Right: Thinner version with sponge

thinner version without sponge vs  with sponge

 

Thinner version 0.96" OLED WEO012864D-Hotbar without Sponge:
  • P/N for white without sponge: WEO012864DWPP3N00006
  • P/N for yellow without sponge: WEO012864DLPP3N00004
  • P/N for blue without sponge: WEO012864DBPP3N00001 (might have MOQ)
  • Datasheet Download

 


Thinner version 0.96" OLED WEO012864D-Hotbar with Sponge:
  • P/N for white with sponge: WEO012864DWPP3N00007
  • P/N for yellow with sponge: WEO012864DLPP3N00005
  • P/N for blue with sponge: WEO012864DBPP3N00002 (might have MOQ)
  • Datasheet Download

 

طراحی

0.96 inch OLED display, 0.96 OLED display - WEO012864D-Hotbar (Thinner version without sponge)
OLED 0.96, 0.96 OLED I2C display,thin OLED display - WEO012864D-Hotbar (Thinner Version with Sponge)

مشخصات

عملکرد پین رابط

.No نماد عملکرد
1 N.C. GND (Reserved Pin (Supporting Pin
.The supporting pins can reduce the influences from stresses on the function pins. These pins must be connected to external ground
2 C2N Positive Terminal of the Flying Inverting Capacitor>Negative Terminal of the Flying Boost Capacitor>The charge-pump capacitors are required between the terminals. They must be floated .when the converter is not used
3 C2P
4 C1P
5 C1N
6 VBAT Power Supply for DC/DC Converter Circuit
This is the power supply pin for the internal buffer of the DC/DC voltage converter. It must be connected to external source when the converter is used. It should be connected to VDD when the converter is not used.
7 NC NC
8 VSS Ground of Logic Circuit
.This is a ground pin. It acts as a reference for the logic pins. It must be connected to external ground
9 VDD Power Supply for Logic
.This is a voltage supply pin. It must be connected to external source
10 BS0 Communicating Protocol Select
These pins are MCU interface selection input. See the
following table:
11 BS1
12 BS2
13 #CS Chip Select
.This pin is the chip select input. The chip is enabled for MCU communication only when CS# is pulled low
14 #RES Power Reset for Controller and Driver
.This pin is reset signal input. When the pin is low, initialization of the chip is executed
15 #D/C Data/Command Control
.This pin is Data/Command control pin. When the pin is pulled high, the input at D7~D0 is treated as display data
When the pin is pulled low, the input at D7~D0 will be transferred to the command register. For detail relationship to MCU interface signals, please refer to the Timing Characteristics .Diagrams
When the pin is pulled high and serial interface mode is selected, the data at SDIN is treated as data. When it is pulled low, the data at SDIN will be transferred to the command register. In .I2C mode, this pin acts as SA0 for slave address selection
16 #R/W Read/Write Select or Write
This pin is MCU interface input. When interfacing to a 68XX-series microprocessor, this pin will be used as Read/Write (R/W#) selection input. Pull this pin to “High” for read mode and .pull it to “Low” for write mode
.When 80XX interface mode is selected, this pin will be the Write (WR#) input. Data write operation is initiated when this pin is pulled low and the CS# is pulled low
17 #E/RD Read/Write Enable or Read
This pin is MCU interface input. When interfacing to a 68XX-series microprocessor, this pin will be used as the Enable (E) signal. Read/write operation is initiated when this pin is pulled high and the CS# is pulled low
.When connecting to an 80XX-microprocessor, this pin receives the Read (RD#) signal. Data read operation is initiated when this pin is pulled low and CS# is pulled low
18~25 D0~D7 Host Data Input/Output Bus
These pins are 8-bit bi-directional data bus to be connected to the microprocessor's data bus. When serial mode is selected, D1 will be the serial data input SDIN and D0 will be the serial clock input SCLK. When I2C mode is selected, D2 & D1 should be tired together and serve as SDAout & SDAin in application and D0 is the serial clock input SCL.
26 IREF Current Reference for Brightness Adjustment
.This pin is segment current reference pin. A resistor should be connected between this pin and VSS. Set the current lower than 12.5μA
27 VCOMH Voltage Output High Level for COM Signal
.This pin is the input pin for the voltage output high level for COM signals. A capacitor should be connected between this pin and VSS
28 VCC Power Supply for OEL Panel
This is the most positive voltage supply pin of the chip. A stabilization capacitor should be connected between this pin and VSS when the converter is used. It must be connected to external .source when the converter is not used
29 VLSS Ground of Analog Circuit
.This is an analog ground pin. It should be connected to VSS externally
30 NC
(GND)
Reserved Pin)Supporting Pin)
.The supporting pins can reduce the influences from stresses on the function pins. These pins must be connected to external ground

داده مکانیکی

مورد WEO012864D-Hotbar
 without Sponge Thinner version
WEO012864D-Hotbar
Thinner version with Sponge
واحد
ابعاد ماژول 26.7 × 19.26 × 1.26 26.7 × 19.26 × 1.61 mm
ناحیه در حال نمایش 23.938 × 12.058 23.938 × 12.058 mm
ناحیه فعال 21.738 × 10.858 21.738 × 10.858 mm
درجه نقطه 0.17 × 0.17 0.17 × 0.17 mm
اندازه نقطه 0.148 × 0.148 0.148 × 0.148 mm
رنگ صفحه‌نمایش 1/64 Duty 1/64 Duty  
IC SSD1306BZ SSD1306BZ  
رابط 6800,8080,SPI,I2C 6800,8080,SPI,I2C  
قطری 0.96 0.96 اینچ

مشخصات الکترونیکی

مورد نماد وضعیت مقدار حداقل مقدار معمول مقدار حداکثر واحد
Supply Voltage for Logic VDD 2.8 3.0 3.3 V
Supply Voltage for Display VCC 11.5 12.0 12.5 V
.Input High Volt VIH 0.8×VDD VDDIO V
.Input Low Volt VIL 0 0.2×VDD V
.Output High Volt VOH 0.9×VDD VDDIO V
.Output Low Volt VOL 0 0.1×VDD V
(Operating Current for VCC (50% display ON ICC 16.0 20.0 mA
 

Search keyword: 128x64 oled, oled 128x64, 0.96 oled, 0.96" oled, 0.96 inch oled, oled 0.96, oled 0.96", 0.96 oled display

go top
close