WEO012864D é um display OLED gráfico COG de 0,96 polegadas com 128x64 pontos. Este módulo tem dimensão de módulo de 26,70 x 19,26 mm e área ativa de 21,738 x 10,858 mm. O Diodo Emissor de Luz Orgânica (OLED da sigla em inglês) é uma tecnologia da nova geração, com imagens mais brilhantes e claras e com uma velocidade de resposta mais ágil.
Este display OLED de 0,96" está integrado com o IC SSD1306, suporta interface 6800, 8080, SPI e I2C , 1/64 para o acionamento, relação de contraste de 10,000:1. A tensão de alimentação para lógica (VDD) é de 2,8V a 3,3V, valor típico de 3,0V . Esta série de módulos pode operar a temperaturas de -40℃ a +80℃; suas temperaturas de armazenamento variam de -40℃ a +85℃.
Este módulo é um display COG OLED de tamanho pequeno, ultra-fino, leve e com baixo consumo de energia. Ele é muito adequado para aplicações domésticas inteligentes, dispositivos médicos, dispositivos portáteis e dispositivos vestíveis.
Left: Thinner version without sponge
Right: Thinner version with sponge
Thinner version 0.96" OLED WEO012864D-Hotbar without Sponge:
Thinner version 0.96" OLED WEO012864D-Hotbar with Sponge
Reserved Pin (Supporting Pin)
The supporting pins can reduce the influences from stresses on the function pins. These pins must be connected to external ground.
2
C2N
Positive Terminal of the Flying Inverting Capacitor Negative Terminal of the Flying Boost Capacitor The charge-pump capacitors are required between the terminals. They must be floated when the converter is not used.
3
C2P
4
C1P
5
C1N
6
VBAT
Power Supply for DC/DC Converter Circuit
This is the power supply pin for the internal buffer of the DC/DC voltage converter. It must be connected to external source when the converter is used. It should be connected to VDD when the converter is not used.
7
NC
NC
8
VSS
Ground of Logic Circuit
This is a ground pin. It acts as a reference for the logic pins. It must be connected to external ground.
9
VDD
Power Supply for Logic
This is a voltage supply pin. It must be connected to external source.
10
BS0
Communicating Protocol Select
These pins are MCU interface selection input. See the
following table:
11
BS1
12
BS2
13
CS#
Chip Select
This pin is the chip select input. The chip is enabled for MCU communication only when CS# is pulled low.
14
RES#
Power Reset for Controller and Driver
This pin is reset signal input. When the pin is low, initialization of the chip is executed.
15
D/C#
Data/Command Control
This pin is Data/Command control pin. When the pin is pulled high, the input at D7~D0 is treated as display data.
When the pin is pulled low, the input at D7~D0 will be transferred to the command register. For detail relationship to MCU interface signals, please refer to the Timing Characteristics Diagrams.
When the pin is pulled high and serial interface mode is selected, the data at SDIN is treated as data. When it is pulled low, the data at SDIN will be transferred to the command register. In I2C mode, this pin acts as SA0 for slave address selection.
16
R/W#
Read/Write Select or Write
This pin is MCU interface input. When interfacing to a 68XX-series microprocessor, this pin will be used as Read/Write (R/W#) selection input. Pull this pin to “High” for read mode and pull it to “Low” for write mode.
When 80XX interface mode is selected, this pin will be the Write (WR#) input. Data write operation is initiated when this pin is pulled low and the CS# is pulled low.
17
E/RD#
Read/Write Enable or Read
This pin is MCU interface input. When interfacing to a 68XX-series microprocessor, this pin will be used as the Enable (E) signal. Read/write operation is initiated when this pin is pulled high and the CS# is pulled low.
When connecting to an 80XX-microprocessor, this pin receives the Read (RD#) signal. Data read operation is initiated when this pin is pulled low and CS# is pulled low.
18~25
D0~D7
Host Data Input/Output Bus
These pins are 8-bit bi-directional data bus to be connected to the microprocessor’s data bus. When serial mode is selected, D1 will be the serial data input SDIN and D0 will be the serial clock input SCLK. When I2C mode is selected, D2 & D1 should be tired together and serve as SDAout & SDAin in application and D0 is the serial clock input SCL.
26
IREF
Current Reference for Brightness Adjustment
This pin is segment current reference pin. A resistor should be connected between this pin and VSS. Set the current lower than 12.5μA.
27
VCOMH
Voltage Output High Level for COM Signal
This pin is the input pin for the voltage output high level for COM signals. A capacitor should be connected between this pin and VSS.
28
VCC
Power Supply for OEL Panel
This is the most positive voltage supply pin of the chip. A stabilization capacitor should be connected between this pin and VSS when the converter is used. It must be connected to external source when the converter is not used.
29
VLSS
Ground of Analog Circuit
This is an analog ground pin. It should be connected to VSS externally.
30
NC
(GND)
Reserved Pin (Supporting Pin)
The supporting pins can reduce the influences from stresses on the function pins. These pins must be connected to external ground.
Ao clicar em "Permitir todos os cookies", você concorda com o armazenamento de cookies no seu dispositivo para melhorar a navegação no site, analisar o uso do site e auxiliar nossos esforços de marketing e desempenho. Você pode encontrar mais informações sobre esse assunto em nossa política. Política de privacidade