1.28 inch SH1106 OLED Display
Model No. WEO012864L
►Type: Graphic
►Structure: COG
►Size: 1.28 inch
►OLED Module 128x64
►3V power supply
►1/64 duty cycle
►Interface: 6800 / 8080 / 3-SPI /4-SPI / I2C
►IC:SH1106
►Display Color: White / Yellow / Sky Blue
►Other FPC options available in below table
Description
WEO012864L is a 1.28" SH1106 COG graphic OLED display module; it's made of 128x64 dot matrix format. This 1.28 oled module is built in controller SH1106G oled IC; it supports 8-bit 6800 and 8080, 3-wire/4-wire SPI and I2C interfaces. Winstar provides ZIF FPC and Hotbar versions for customers to choose the suitable module for your application. These SH1106 OLED COG modules are ultra thin, lightweight and low power consumption which is great for handheld instruments, meters, smart grid medical device, IoT system, etc.WEO012864L module supports internal Charge Pump supply and external VCC supply.

DRAWING
WEO012864L with Hotbar FPC

Data source ref: WEO012864LLAP3N00000
WEO012864L with ZIF FPC

Data source ref: WEO012864LLAP3N00F00
SPECIFICATIONS
Interface Pin Function
No. | Symbol | Function | ||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
1 | NC(GND) | No connection | ||||||||||||||||||||||||
2 | C1N | Connect to charge pump capacitor. These pins are not used and should be disconnected when Vpp is supplied externally. |
||||||||||||||||||||||||
3 | C1P | |||||||||||||||||||||||||
4 | C2P | Connect to charge pump capacitor. These pins are not used and should be disconnected when Vpp is supplied externally. |
||||||||||||||||||||||||
5 | C2N | |||||||||||||||||||||||||
6 | VDD2 | 3.0 – 4.7V power supply pad for Power supply for charge pump circuit. This pin should be disconnected when VPP is supplied externally |
||||||||||||||||||||||||
7 | NC | No connection | ||||||||||||||||||||||||
8 | VSS | Ground. | ||||||||||||||||||||||||
9 | VDD1 | Power supply input: 1.65 - 3.5V | ||||||||||||||||||||||||
10 | IM0 | These are the MPU interface mode select pads.
|
||||||||||||||||||||||||
11 | IM1 | |||||||||||||||||||||||||
12 | IM2 | |||||||||||||||||||||||||
13 | CSB | This pad is the chip select input. When CSB = “L”, then the chip select becomes active, and data/command I/O is enabled. | ||||||||||||||||||||||||
14 | RESB | This is a reset signal input pad. When RES is set to “L”, the settings are initialized. The reset operation is performed by the RES signal level. | ||||||||||||||||||||||||
15 | A0 | This is the Data/Command control pad that determines whether the data bits are data or a command. A0 = “H”: the inputs at D0 to D7 are treated as display data. A0 = “L”: the inputs at D0 to D7 are transferred to the command registers. In I2C interface, this pad serves as SA0 to distinguish the different address of OLED driver. |
||||||||||||||||||||||||
16 | WRB | This is a MPU interface input pad. When connected to an 8080 MPU, this is active LOW. This pad connects to the 8080 MPU WR signal. The signals on the data bus are latched at the rising edge of the WR signal. When connected to a 6800 Series MPU: This is the read/write control signal input terminal. When R/W = “H”: Read. When R/W = “L”: Write. |
||||||||||||||||||||||||
17 | RDB | This is a MPU interface input pad. When connected to an 8080 series MPU, it is active LOW. This pad is connected to the RD signal of the 8080 series MPU, and the data bus is in an output status when this signal is “L”. When connected to a 6800 series MPU , this is active HIGH. This is used as an enable clock input of the 6800 series MPU. When RD = “H”: Enable. When RD = “L”: Disable. |
||||||||||||||||||||||||
18 | D0 | This is an 8-bit bi-directional data bus that connects to an 8-bit or 16-bit standard MPU data bus. When the serial interface is selected, then D0 serves as the serial clock input pad (SCL) and D1 serves as the serial data input pad (SI). At this time, D2 to D7 are set to high impedance. When the I2C interface is selected, then D0 serves as the serial clock input pad (SCL) and D1 serves as the serial data input pad (SDAI). At this time, D2 to D7 are set to high impedance. |
||||||||||||||||||||||||
19 | D1 | |||||||||||||||||||||||||
20 | D2 | |||||||||||||||||||||||||
21 | D3 | |||||||||||||||||||||||||
22 | D4 | |||||||||||||||||||||||||
23 | D5 | |||||||||||||||||||||||||
24 | D6 | |||||||||||||||||||||||||
25 | D7 | |||||||||||||||||||||||||
26 | IREF | This is a segment current reference pad. A resistor should be connected between this pad and VSS. Set the current at 18.75uA. | ||||||||||||||||||||||||
27 | VCOMH | This is a pad for the voltage output high level for common signals. A capacitor should be connected between this pad and VSS. |
||||||||||||||||||||||||
28 | VPP | OLED panel power supply. Generated by internal charge pump. Connect to capacitor. It could be supplied externally. |
||||||||||||||||||||||||
29 | VSL | This is a segment voltage reference pad. This pad should be connected to VSS externally. |
||||||||||||||||||||||||
30 | NC(GND) | No connection |
Mechanical Data
Item | Dimension | Unit |
---|---|---|
Dot Matrix | 128 x 64 | - |
Module dimension | 34.50 × 23.00 × 1.65 | mm |
Active Area | 29.42 × 14.20 | mm |
Pixel Size | 0.205 × 0.197 | mm |
Pixel Pitch | 0.230 × 0.222 | mm |
Display Mode | Passive Matrix | |
Display Color | Monochrome | |
Drive Duty | 1/64 Duty | |
Controller IC | SH1106 | |
Interface | 6800/8080/3-SPI /4-SPI / I2C | |
Size | 1.28 inch |
Absolute Maximum Ratings
Parameter | Symbol | Min | Max | Unit |
---|---|---|---|---|
Supply Voltage for Logic | VDD1 | -0.3 | 3.6 | V |
Power supply for charge pump circuit | VDD2 | -0.3 | 4.8 | V |
Supply Voltage for Display | VPP | -0.3 | 14.5 | V |
Operating Temperature | TOP | -40 | +80 | °C |
Storage Temperature | TSTG | -40 | +85 | °C |
Electronical Characteristics
DC Electrical Characteristics
Item | Symbol | Condition | Min | Typ | Max | Unit |
---|---|---|---|---|---|---|
Supply Voltage for Logic | VDD1 | - | 2.8 | 3.0 | 3.3 | V |
Supply Voltage for Display | VPP | - | 6.75 | 7.25 | 7.75 | V |
High Level Input | VIH | - | 0.8xVDD1 | - | VDD1 | V |
Low Level Input | VIL | - | VSS | - | 0.2xVDD1 | V |
High Level Output | VOH | - | 0.8xVDD1 | - | VDD1 | V |
Low Level Output | VOL | - | VSS | - | 0.2xVDD1 | V |
50% Check Board operating Current | VPP =7.25V | 5.0 | 6.0 | 7.0 | mA |
FPC Options:
Drawing | FPC Length | PIN | Pitch | ZIF FPC or HOTBAR FPC | Interface | FPC No. | Create Date |
---|---|---|---|---|---|---|---|
![]() |
13.2 | 30 | 0.7 | HOTBAR FPC | 6800/8080/3-SPI /4-SPI / I2C | FPC2070003001XXXXX03 | 20141107 |
![]() |
51.15 | 30 | 0.5 | ZIF | 6800/8080/3-SPI /4-SPI / I2C | FPC2050003011XXXXX18 | 20180123 |
Search keyword: 128x64 oled, oled 128x64, 1.28 oled, 1.28" oled, 1.28 inch oled, oled 1.28, oled 1.28", SH1106 oled