Home Prodotti Display OLED Display OLED Grafici WEO012864L

1.28" SH1106 Display Pannelli OLED

Modello numero WEO012864L

►Tipo: grafico
►Struttura: COG
►Dimensione: 1.28 pollici
►128x64 a matrice di punti
►Alimentatore 3V
►1/64 duty cycle
►Interfaccia: 6800 / 8080 / 3-SPI /4-SPI / I2C
►IC:SH1106
►Colore display: Bianco / Giallo / Cielo blu
►Altre opzioni FPC disponibili nella tabella di seguito

Descrizione

   Opzioni FPC

 

DISEGNO

WEO012864L with Hotbar FPC

SH1106 OLED Display, 1.28 inch OLED, OLED SH1106 - WEO012864L with Hotbar FPC

Data source ref: WEO012864LLAP3N00000

 

WEO012864L with ZIF FPC

Winstar SH1106 OLED, 1.28 inch OLED - WEO012864L with ZIF FPC

Data source ref: WEO012864LLAP3N00F00

SPECIFICHE TECNICHE

Funzione dei Pin di Interfaccia

No. Simbolo Funzione
1 NC(GND) No connection
2 C1N Connect to charge pump capacitor.
These pins are not used and should be disconnected when Vpp is supplied externally.
3 C1P
4 C2P Connect to charge pump capacitor.
These pins are not used and should be disconnected when Vpp is supplied externally.
5 C2N
6 VDD2 3.0 – 4.7V power supply pad for Power supply for charge pump circuit.
This pin should be disconnected when VPP is supplied externally
7 NC No connection
8 VSS Ground.
9 VDD1 Power supply input: 1.65 - 3.5V
10 IM0 These are the MPU interface mode select pads.
  8080 I2C 6800 4-wire SPI 3-wire SPI
IM0 0 0 0 0 1
IM1 1 1 0 0 0
IM2 1 0 1 0 0
11 IM1
12 IM2
13 CSB This pad is the chip select input. When CSB = “L”, then the chip select becomes active, and data/command I/O is enabled.
14 RESB This is a reset signal input pad. When RES is set to “L”, the settings are initialized. The reset operation is performed by the RES signal level.
15 A0 This is the Data/Command control pad that determines whether the data bits are data or a command.
A0 = “H”: the inputs at D0 to D7 are treated as display data.
A0 = “L”: the inputs at D0 to D7 are transferred to the command registers.
In I2C interface, this pad serves as SA0 to distinguish the different address of OLED driver.
16 WRB This is a MPU interface input pad.
When connected to an 8080 MPU, this is active LOW. This pad connects to the 8080 MPU WR signal. The signals on the data bus are latched at the rising edge of the WR signal.
When connected to a 6800 Series MPU: This is the read/write control signal input terminal.
When R/W = “H”: Read.
When R/W = “L”: Write.
17 RDB This is a MPU interface input pad.
When connected to an 8080 series MPU, it is active LOW. This pad is connected to the RD signal of the 8080 series MPU, and the data bus is in an output status when this signal is “L”.
When connected to a 6800 series MPU , this is active HIGH. This is used as an enable clock input of the 6800 series MPU.
When RD = “H”: Enable.
When RD = “L”: Disable.
18 D0 This is an 8-bit bi-directional data bus that connects to an 8-bit or 16-bit standard MPU data bus.
When the serial interface is selected, then D0 serves as the serial clock input pad (SCL) and D1 serves as the serial data input pad (SI). At this time, D2 to D7 are set to high impedance.
When the I2C interface is selected, then D0 serves as the serial clock input pad (SCL) and D1 serves as the serial data input pad (SDAI). At this time, D2 to D7 are set to high impedance.
19 D1
20 D2
21 D3
22 D4
23 D5
24 D6
25 D7
26 IREF This is a segment current reference pad. A resistor should be connected between this pad and VSS. Set the current at 18.75uA.
27 VCOMH This is a pad for the voltage output high level for common signals.
A capacitor should be connected between this pad and VSS.
28 VPP OLED panel power supply. Generated by internal charge pump.
Connect to capacitor. It could be supplied externally.
29 VSL This is a segment voltage reference pad.
This pad should be connected to VSS externally.
30 NC(GND) No connection

Dati meccanici

Articolo Dimensioni Unità
A matrice di punti 128 x 64
Dimensione del modulo 34.50 × 23.00 × 1.65 mm
Area attiva 29.42 × 14.20 mm
Dimensioni del Dot 0.205 × 0.197 mm
Passo del Dot 0.230 × 0.222 mm
Modalità display Matrice passiva
Colore display monocromatici
Drive Duty 1/64 Duty
Controllo IC SH1106
Interfaccia 6800/8080/3-SPI /4-SPI / I2C
Dimensione 1.28 pollici

Valori massimi assoluti

Parameter Simbolo Valore Min Valore massimo Unità
Supply Voltage for Logic VDD1 -0.3 3.6 V
Power supply for charge pump circuit VDD2 -0.3 4.8 V
Supply Voltage for Display VPP -0.3 14.5 V
Temperatura di lavoro TOP -40 +80 °C
Temperatura di stock TSTG -40 +85 °C

Caratteristiche elettriche

DC Caratteristiche elettriche

Articolo Simbolo Condizione Valore Min Valore tipico Valore massimo Unità
Supply Voltage for Logic VDD1 2.8 3.0 3.3 V
Supply Voltage for Display VPP 6.75 7.25 7.75 V
High Level Input VIH 0.8xVDD1 VDD1 V
Low Level Input VIL VSS 0.2xVDD1 V
High Level Output VOH 0.8xVDD1 VDD1 V
Low Level Output VOL VSS 0.2xVDD1 V
50% Check Board operating Current VPP =7.25V 5.0 6.0 7.0 mA

Opzioni FPC:

Immagine FPC Length PIN Pitch ZIF FPC or HOTBAR FPC Interfaccia FPC No. Create Date
FPC2070003001XXXXX03_WEO012864LLPP3N00000 13.2 30 0.7 HOTBAR FPC 6800/8080/3-SPI /4-SPI / I2C FPC2070003001XXXXX03 20141107
FPC2050003011XXXXX18_WEO012864LWAP3N00F00 51.15 30 0.5 ZIF  6800/8080/3-SPI /4-SPI / I2C FPC2050003011XXXXX18 20180123
 

Search keyword: 128x64 oled, oled 128x64, 1.28 oled, 1.28" oled, 1.28 pollici oled, oled 1.28, oled 1.28"

go top
close