Home Produtos Display OLED Display OLED Gráfico WEO012864L

SH1106 OLED Display de 1,28 polegadas, Display OLED SH1106 resolução de 128x64

Model No. WEO012864L

►Tipo: Gráfico
►Estrutura: COG
►Tamanho: 1,28 polegadas
►Matriz de pontos 128x64
►Alimentação 3V
►1/64 duty cycle
►Interface: 6800 / 8080 / 3-SPI /4-SPI / I2C
►IC:SH1106
►Display Color: Branco / Amarelo / Céu azul
►Other FPC options available in below table

Descrição

WEO012864L é um display OLED de 1,28 polegadas está integrado com o IC SH1106G, suporta interface 6800, 8080, SPI de 3/4 fios e I2C. Este módulo tem dimensão de módulo de 34,5 x 23 mm e área ativa de 29,42 x 14,2 mm, resolução de 128x64 pixéis e 1/64 duty.

Este módulo é um display COG OLED de tamanho pequeno, ultra-fino, leve e com baixo consumo de energia. Ele é muito adequado para aplicações domésticas inteligentes, dispositivos médicos e dispositivos portáteis.

A tensão de alimentação para lógica (VDD) é de 2,8V a 3,3V, valor típico de 3V. Esta série de SH1106 OLED display pode operar a temperaturas de -40℃ a +80℃; suas temperaturas de armazenamento variam de -40℃ a +85℃.


   FPC Options

 

DRAWING

WEO012864L with Hotbar FPC

SH1106 OLED Display, 1.28 inch OLED, OLED SH1106 - WEO012864L with Hotbar FPC

Data source ref: WEO012864LLAP3N00000

 

WEO012864L with ZIF FPC

Winstar SH1106 OLED, 1.28 inch OLED - WEO012864L with ZIF FPC

Data source ref: WEO012864LLAP3N00F00

SPECIFICATIONS

Função do pino de interface

No. Símbolo Função
1 NC(GND) No connection
2 C1N Connect to charge pump capacitor.
These pins are not used and should be disconnected when Vpp is supplied externally.
3 C1P
4 C2P Connect to charge pump capacitor.
These pins are not used and should be disconnected when Vpp is supplied externally.
5 C2N
6 VDD2 3.0 – 4.7V power supply pad for Power supply for charge pump circuit.
This pin should be disconnected when VPP is supplied externally
7 NC No connection
8 VSS Ground.
9 VDD1 Power supply input: 1.65 - 3.5V
10 IM0 These are the MPU interface mode select pads.
  8080 I2C 6800 4-wire SPI 3-wire SPI
IM0 0 0 0 0 1
IM1 1 1 0 0 0
IM2 1 0 1 0 0
11 IM1
12 IM2
13 CSB This pad is the chip select input. When CSB = “L”, then the chip select becomes active, and data/command I/O is enabled.
14 RESB This is a reset signal input pad. When RES is set to “L”, the settings are initialized. The reset operation is performed by the RES signal level.
15 A0 This is the Data/Command control pad that determines whether the data bits are data or a command.
A0 = “H”: the inputs at D0 to D7 are treated as display data.
A0 = “L”: the inputs at D0 to D7 are transferred to the command registers.
In I2C interface, this pad serves as SA0 to distinguish the different address of OLED driver.
16 WRB This is a MPU interface input pad.
When connected to an 8080 MPU, this is active LOW. This pad connects to the 8080 MPU WR signal. The signals on the data bus are latched at the rising edge of the WR signal.
When connected to a 6800 Series MPU: This is the read/write control signal input terminal.
When R/W = “H”: Read.
When R/W = “L”: Write.
17 RDB This is a MPU interface input pad.
When connected to an 8080 series MPU, it is active LOW. This pad is connected to the RD signal of the 8080 series MPU, and the data bus is in an output status when this signal is “L”.
When connected to a 6800 series MPU , this is active HIGH. This is used as an enable clock input of the 6800 series MPU.
When RD = “H”: Enable.
When RD = “L”: Disable.
18 D0 This is an 8-bit bi-directional data bus that connects to an 8-bit or 16-bit standard MPU data bus.
When the serial interface is selected, then D0 serves as the serial clock input pad (SCL) and D1 serves as the serial data input pad (SI). At this time, D2 to D7 are set to high impedance.
When the I2C interface is selected, then D0 serves as the serial clock input pad (SCL) and D1 serves as the serial data input pad (SDAI). At this time, D2 to D7 are set to high impedance.
19 D1
20 D2
21 D3
22 D4
23 D5
24 D6
25 D7
26 IREF This is a segment current reference pad. A resistor should be connected between this pad and VSS. Set the current at 18.75uA.
27 VCOMH This is a pad for the voltage output high level for common signals.
A capacitor should be connected between this pad and VSS.
28 VPP OLED panel power supply. Generated by internal charge pump.
Connect to capacitor. It could be supplied externally.
29 VSL This is a segment voltage reference pad.
This pad should be connected to VSS externally.
30 NC(GND) No connection

Dados Mecânicos

Item Dimensão Unidade
Matriz de pontos 128 x 64
Dimensão do módulo 34.50 × 23.00 × 1.65 mm
Área ativa 29.42 × 14.20 mm
Tamanho do ponto 0.205 × 0.197 mm
Distância entre pontos 0.230 × 0.222 mm
Modo de exibição Passive Matrix
Cor de exibição Monochrome
Drive Duty 1/64 Duty
Controller IC SH1106
Interface 6800/8080/3-SPI /4-SPI / I2C
Tamanho 1,28 polegadas

Classificações Máximas Absolutas

Parameter Símbolo Valor Min Valor Máximo Unidade
Supply Voltage for Logic VDD1 -0.3 3.6 V
Power supply for charge pump circuit VDD2 -0.3 4.8 V
Supply Voltage for Display VPP -0.3 14.5 V
Temperatura de operação TOP -40 +80 °C
Temperatura de armazenamento TSTG -40 +85 °C

Características Eletrônicas

DC Características Eletrônicas

Item Símbolo Condição Valor Min Valor Típico Valor Máximo Unidade
Supply Voltage for Logic VDD1 2.8 3.0 3.3 V
Supply Voltage for Display VPP 6.75 7.25 7.75 V
High Level Input VIH 0.8xVDD1 VDD1 V
Low Level Input VIL VSS 0.2xVDD1 V
High Level Output VOH 0.8xVDD1 VDD1 V
Low Level Output VOL VSS 0.2xVDD1 V
50% Check Board operating Current VPP =7.25V 5.0 6.0 7.0 mA

FPC Options:

Drawing FPC Length PIN Pitch ZIF FPC or HOTBAR FPC Interface FPC No. Create Date
FPC2070003001XXXXX03_WEO012864LLPP3N00000 13.2 30 0.7 HOTBAR FPC 6800/8080/3-SPI /4-SPI / I2C FPC2070003001XXXXX03 20141107
FPC2050003011XXXXX18_WEO012864LWAP3N00F00 51.15 30 0.5 ZIF  6800/8080/3-SPI /4-SPI / I2C FPC2050003011XXXXX18 20180123
go top
close