64x128 SH1107 OLED Display, OLED 64x128
Model No. WEO064128A
►Type: Graphic
►Structure: COG
►Size: 0.96"
►OLED resolution 64x128 dots, 64x128 OLED
►IC：SH1107
►3V Power supply
►1/64 duty
►Interface: SPI, I2C
►Display Color: White / Yellow
Description
WEO064128A model is a consumer-grade COG OLED display, diagonal size 0.96 inch, made of resolution 64x128 dots. This 64x128 OLED display module is built-in with SH1107 IC; it supports 4-wire SPI and I2C interface, the supply voltage for logic 3V, the supply voltage for display 9V, the display with 50% Checkboard current is 8mA @9V VCC (typical value), driving duty 1/64.
WEO064128A model SH1107 OLED display resolution 64x128 is suitable for wearable devices, portable devices, etc. It can be operated at temperatures from –30℃ to +70℃; its storage temperatures range from -30℃ to +70℃.
DRAWING
Data source ref: WEO064128AWPP3N0Y000
SPECIFICATIONS
Interface Pin Function
| No. | Symbol | Function |
|---|---|---|
| 1 | NC | Not connected. |
| 2 | VPP | This is the most positive voltage supply pad of the chip. It should be supplied externally. |
| 3 | VCOMH | This is a pad for the voltage output high level for common signals. A capacitor should be connected between this pad and VSS. |
| 4 | VDD | Power supply for logic and input. |
| 5 | IM1 | These are the MPU interface mode select pads. IM1 connect to VDD is I2C interface. IM1 connect to GND is 4-wire SPI interface. |
| 6 | IREF | This is a segment current reference pad. A resistor should be connected between this pad and VSS. Set the current at 15.625mA. |
| 7 | CS | This pad is the chip select input. When CS = “L”, then the chip select becomes active, and data/command I/O is enabled. |
| 8 | RES | This is a reset signal input pad. When RES is set to “L”, the settings are initialized. The reset operation is performed by the RES signal level. |
| 9 | DC | This is the Data/Command control pad that determines whether the data bits are data or a command. DC = “H”: the inputs at D0 to D1 are treated as display data. DC = “L”: the inputs at D0 to D1 are transferred to the command registers. In I2C interface, this pad serves as SA0 to distinguish the different address of OLED driver. |
| 10 | D0 | When the serial interface is selected, then D0 serves as the serial clock input pad (SCL) and D1 serves as the serial data input pad (SI). When the I2C interface is selected, then D0 serves as the serial clock input pad (SCL) and D1 serves as the serial data input pad (SDA). |
| 11 | D1 | |
| 12 | VSS | Ground. |
| 13 | NC | Not connected. |
Mechanical Data
| Item | Dimension | Unit |
|---|---|---|
| Dot Matrix | 64 x 128 | Dots |
| Module dimension | 14.0 × 28.0 × 1.26 | mm |
| Active Area | 10.86× 21.74 | mm |
| Pixel Size | 0.15 × 0.15 | mm |
| Pixel Pitch | 0.17 × 0.17 | mm |
| Display Mode | Passive Matrix | |
| Display Color | Monochrome | |
| Drive Duty | 1/64 Duty | |
| IC | SH1107 | |
| Interface | 4-wire SPI , I2C | |
| Size | 0.96 inch | |
Absolute Maximum Ratings
| Parameter | Symbol | Min | Max | Unit |
|---|---|---|---|---|
| Supply Voltage for Logic | VDD | -0.3 | 3.6 | V |
| Supply Voltage for Display | VPP | -0.3 | 17.0 | V |
| Operating Temperature | TOP | -30 | +70 | °C |
| Storage Temperature | TSTG | -30 | +70 | °C |
Electronical Characteristics
| Item | Symbol | Condition | Min | Typ | Max | Unit |
|---|---|---|---|---|---|---|
| Supply Voltage for Logic | VDD | － | 1.65 | 3.0 | 3.3 | V |
| Supply Voltage for Display | VPP | － | 7.0 | 9.0 | 9.5 | V |
| Input High Volt. | VIH | － | 0.8×VDD | － | VDD | V |
| Input Low Volt. | VIL | － | 0 | － | 0.2×VDD | V |
| Output High Volt. | VOH | － | 0.8×VDD | － | VDD | V |
| Output Low Volt. | VOL | － | 0 | － | 0.2×VDD | V |
| Operating Current for VCC (50% display ON) | IPP | VPP=9V | － | 8 | 12 | mA |
Search keyword: 64x128 oled, oled 64x128, 0.96 oled, 0.96" oled, 0.96 inch oled, oled 0.96, oled 0.96"
