0.96 pollici SH1107 OLED Grafici 64x128
Modello numero WEO064128A
►Tipo: grafico
►Struttura: COG
►Dimensione: 0.96 pollici
►64x128 a matrice di punti
►IC：SH1107
►Alimentatore 3V
►1/64 duty
►Interfaccia: SPI, I2C
►Colore display: Bianco / Giallo
DISEGNO
Data source ref: WEO064128AWPP3N0Y000
SPECIFICHE TECNICHE
Funzione dei Pin di Interfaccia
| No. | Simbolo | Funzione |
|---|---|---|
| 1 | NC | Not connected. |
| 2 | VPP | This is the most positive voltage supply pad of the chip. It should be supplied externally. |
| 3 | VCOMH | This is a pad for the voltage output high level for common signals. A capacitor should be connected between this pad and VSS. |
| 4 | VDD | Power supply for logic and input. |
| 5 | IM1 | These are the MPU interface mode select pads. IM1 connect to VDD is I2C interface. IM1 connect to GND is 4-wire SPI interface. |
| 6 | IREF | This is a segment current reference pad. A resistor should be connected between this pad and VSS. Set the current at 15.625mA. |
| 7 | CS | This pad is the chip select input. When CS = “L”, then the chip select becomes active, and data/command I/O is enabled. |
| 8 | RES | This is a reset signal input pad. When RES is set to “L”, the settings are initialized. The reset operation is performed by the RES signal level. |
| 9 | DC | This is the Data/Command control pad that determines whether the data bits are data or a command. DC = “H”: the inputs at D0 to D1 are treated as display data. DC = “L”: the inputs at D0 to D1 are transferred to the command registers. In I2C interface, this pad serves as SA0 to distinguish the different address of OLED driver. |
| 10 | D0 | When the serial interface is selected, then D0 serves as the serial clock input pad (SCL) and D1 serves as the serial data input pad (SI). When the I2C interface is selected, then D0 serves as the serial clock input pad (SCL) and D1 serves as the serial data input pad (SDA). |
| 11 | D1 | |
| 12 | VSS | Ground. |
| 13 | NC | Not connected. |
Dati meccanici
| Articolo | Dimensioni | Unità |
|---|---|---|
| A matrice di punti (Risoluzione) | 64 x 128 | Dots |
| Dimensione del modulo | 14.0 × 28.0 × 1.26 | mm |
| Area attiva | 10.86× 21.74 | mm |
| Dimensioni del Dot | 0.15 × 0.15 | mm |
| Passo del Dot | 0.17 × 0.17 | mm |
| Modalità display | Matrice passiva | |
| Colore display | monocromatici | |
| Drive Duty | 1/64 Duty | |
| IC | SH1107 | |
| Interfaccia | 4-wire SPI , I2C | |
| Dimensione (Diagonale) | 0.96 pollici | |
Valori massimi assoluti
| Parameter | Simbolo | Valore Min | Valore massimo | Unità |
|---|---|---|---|---|
| Supply Voltage for Logic | VDD | -0.3 | 3.6 | V |
| Supply Voltage for Display | VPP | -0.3 | 17.0 | V |
| Temperatura di lavoro | TOP | -30 | +70 | °C |
| Temperatura di stock | TSTG | -30 | +70 | °C |
Caratteristiche elettriche
| Articolo | Simbolo | Condizione | Valore Min | Valore tipico | Valore massimo | Unità |
|---|---|---|---|---|---|---|
| Supply Voltage for Logic | VDD | － | 1.65 | 3.0 | 3.3 | V |
| Supply Voltage for Display | VPP | － | 7.0 | 9.0 | 9.5 | V |
| Input High Volt. | VIH | － | 0.8×VDD | － | VDD | V |
| Input Low Volt. | VIL | － | 0 | － | 0.2×VDD | V |
| Output High Volt. | VOH | － | 0.8×VDD | － | VDD | V |
| Output Low Volt. | VOL | － | 0 | － | 0.2×VDD | V |
| Operating Current for VCC (50% display ON) | IPP | VPP=9V | － | 8 | 12 | mA |
Search keyword: 64x128 oled, oled 64x128, 0.96 oled, 0.96" oled, 0.96 pollici oled, oled 0.96, oled 0.96"
