Display Gráfico SH1107 OLED 64x128
Model No. WEO064128A
►Tipo: Gráfico
►Estrutura: COG
►Tamanho: 0,96 polegadas
►Matriz de pontos 64x128
►IC:SH1107
►Alimentação 3V
►1/64 duty
►Interface: SPI, I2C
►Display Color: Branco / Amarelo
Descrição
WEO064128A é um display gráfico OLED de 0,96 polegadas; fabricado com resolução de 64 x 128 pixéis. Este módulo tem dimensão de módulo de 14,0 x 28,0 mm e área ativa de 10,86 x 21,74 mm. Este módulo suporta interface I2C, e SPI de 4 fios. Este modelo está integrado com Ics controladores SH1107.
Gráfico SH1107 OLED WEO064128A A tensão de alimentação para a lógica é de 1,65V a 3,3V, valor típico é 3,0V, tensão de alimentação para o display é de 9,0V, 1/64 para o acionamento. relação de contraste de 10,000:1. Este módulo pode operar a temperaturas de -30℃ a +70℃; suas temperaturas de armazenamento variam de -30℃ a +70℃.
DRAWING
Data source ref: WEO064128AWPP3N0Y000
SPECIFICATIONS
Função do pino de interface
No. | Símbolo | Função |
---|---|---|
1 | NC | Not connected. |
2 | VPP | This is the most positive voltage supply pad of the chip. It should be supplied externally. |
3 | VCOMH | This is a pad for the voltage output high level for common signals. A capacitor should be connected between this pad and VSS. |
4 | VDD | Power supply for logic and input. |
5 | IM1 | These are the MPU interface mode select pads. IM1 connect to VDD is I2C interface. IM1 connect to GND is 4-wire SPI interface. |
6 | IREF | This is a segment current reference pad. A resistor should be connected between this pad and VSS. Set the current at 15.625mA. |
7 | CS | This pad is the chip select input. When CS = “L”, then the chip select becomes active, and data/command I/O is enabled. |
8 | RES | This is a reset signal input pad. When RES is set to “L”, the settings are initialized. The reset operation is performed by the RES signal level. |
9 | DC | This is the Data/Command control pad that determines whether the data bits are data or a command. DC = “H”: the inputs at D0 to D1 are treated as display data. DC = “L”: the inputs at D0 to D1 are transferred to the command registers. In I2C interface, this pad serves as SA0 to distinguish the different address of OLED driver. |
10 | D0 | When the serial interface is selected, then D0 serves as the serial clock input pad (SCL) and D1 serves as the serial data input pad (SI). When the I2C interface is selected, then D0 serves as the serial clock input pad (SCL) and D1 serves as the serial data input pad (SDA). |
11 | D1 | |
12 | VSS | Ground. |
13 | NC | Not connected. |
Dados Mecânicos
Item | Dimensão | Unidade |
---|---|---|
Matriz de pontos | 64 x 128 | Dots |
Dimensão do módulo | 14.0 × 28.0 × 1.26 | mm |
Área ativa | 10.86× 21.74 | mm |
Tamanho do ponto | 0.15 × 0.15 | mm |
Distância entre pontos | 0.17 × 0.17 | mm |
Modo de exibição | Passive Matrix | |
Cor de exibição | Monochrome | |
Drive Duty | 1/64 Duty | |
IC | SH1107 | |
Interface | 4-wire SPI , I2C | |
Tamanho | 0,96 polegadas |
Classificações Máximas Absolutas
Parameter | Símbolo | Valor Min | Valor Máximo | Unidade |
---|---|---|---|---|
Supply Voltage for Logic | VDD | -0.3 | 3.6 | V |
Supply Voltage for Display | VPP | -0.3 | 17.0 | V |
Operating Temperature | TOP | -30 | +70 | °C |
Storage Temperature | TSTG | -30 | +70 | °C |
Características Eletrônicas
Item | Símbolo | Condição | Valor Min | Valor Típico | Valor Máximo | Unidade |
---|---|---|---|---|---|---|
Supply Voltage for Logic | VDD | - | 1.65 | 3.0 | 3.3 | V |
Supply Voltage for Display | VPP | - | 7.0 | 9.0 | 9.5 | V |
Input High Volt. | VIH | - | 0.8×VDD | - | VDD | V |
Input Low Volt. | VIL | - | 0 | - | 0.2×VDD | V |
Output High Volt. | VOH | - | 0.8×VDD | - | VDD | V |
Output Low Volt. | VOL | - | 0 | - | 0.2×VDD | V |
Operating Current for VCC (50% display ON) | IPP | VPP=9V | - | 8 | 12 | mA |