Home Productos Pantalla OLED Pantalla OLED Gráfico WEO064128A

Módulos Gráficos SH1107 OLED 64x128, 0.96 pulgada

Modelo Nº WEO064128A

►Tipo : Gráfico
►Estructura : COG
►Tamaño : 0.96 pulgada
►Matriz de puntos 64x128
►IC:SH1107
►Fuente de alimentación de 3V
►1/64 duty
►Interfaz : SPI, I2C
►Color de la pantalla: Blanco / Amarillo

Descripción

WEO064128A es un Pantalla Gráficos OLED de 0,96 pulgadas que tiene una resolución de 64 x 128 píxeles. Este módulo tiene un tamaño de 14,0 x 28,0 mm y un tamaño de área activa de 10,86 x 21,74 mm. Este módulo es compatible con la interfaz I2C y SPI de 4 cables. Este modelo está integrado con IC de controlador SH1107.

Módulos Gráficos SH1107 OLED WEO064128A El voltaje de suministro para la lógica es de 1,65 V a 3,3 V, con un valor típico de 3,0 V. El voltaje de suministro para pantalla es de 9,0 V, con 1/64 de servicio de impulsión. WEO064128A módulo Gráficos OLED una relación de contraste de 10,000:1. Este módulo puede funcionar a temperaturas de -30 ℃ a +70 ℃ y su temperatura de almacenamiento oscila entre -30 ℃ y +70 ℃.

DIBUJO

64x128 OLED Display, SH1107 OLED Display, OLED 64x128 - WEO064128A

Data source ref: WEO064128AWPP3N0Y000

ESPECIFICACIONES

Función interfaz Pin

No. Símbolo Función
1 NC Not connected.
2 VPP This is the most positive voltage supply pad of the chip.
It should be supplied externally.
3 VCOMH This is a pad for the voltage output high level for common signals.
A capacitor should be connected between this pad and VSS.
4 VDD Power supply for logic and input.
5 IM1 These are the MPU interface mode select pads.
IM1 connect to VDD is I2C interface.
IM1 connect to GND is 4-wire SPI interface.
6 IREF This is a segment current reference pad. A resistor should be connected between this pad and VSS. Set the current at 15.625mA.
7 CS This pad is the chip select input. When CS = “L”, then the chip select becomes active, and data/command I/O is enabled.
8 RES This is a reset signal input pad. When RES is set to “L”, the settings are initialized. The reset operation is performed by the RES signal level.
9 DC This is the Data/Command control pad that determines whether the data bits are data or a command.
DC = “H”: the inputs at D0 to D1 are treated as display data.
DC = “L”: the inputs at D0 to D1 are transferred to the command registers.
In I2C interface, this pad serves as SA0 to distinguish the different address of OLED driver.
10 D0 When the serial interface is selected, then D0 serves as the serial clock input pad (SCL) and D1 serves as the serial data input pad (SI).
When the I2C interface is selected, then D0 serves as the serial clock input pad (SCL) and D1 serves as the serial data input pad (SDA).
11 D1
12 VSS Ground.
13 NC Not connected.

Datos mecánicos

Elemento Dimensión Unidad
Matriz de puntos (Resolución) 64 x 128 Dots
Dimensión del módulo 14.0 × 28.0 × 1.26 mm
zona activa 10.86× 21.74 mm
Tamaño del punto 0.15 × 0.15 mm
Distancia entre puntos 0.17 × 0.17 mm
Modo de visualización Matriz pasiva
Color de la pantalla Monocromos
Drive Duty 1/64 Duty
IC SH1107
Interfaz 4-wire SPI , I2C
Tamaño (Diagonal) 0.96 pulgada

Valores nominales máximos absolutos

Parameter Símbolo Valor mín. Valor máx. Unidad
Supply Voltage for Logic VDD -0.3 3.6 V
Supply Voltage for Display VPP -0.3 17.0 V
Temperatura de funcionamiento TOP -30 +70 °C
Temperatura de almacenamiento TSTG -30 +70 °C

Características electrónicas

Elemento Símbolo Condición Valor mín. Valor típico Valor máx. Unidad
Supply Voltage for Logic VDD 1.65 3.0 3.3 V
Supply Voltage for Display VPP 7.0 9.0 9.5 V
Input High Volt. VIH 0.8×VDD VDD V
Input Low Volt. VIL 0 0.2×VDD V
Output High Volt. VOH 0.8×VDD VDD V
Output Low Volt. VOL 0 0.2×VDD V
Operating Current for VCC (50% display ON)   IPP VPP=9V 8 12 mA

Search keyword: 64x128 oled, oled 64x128, 0.96 oled, 0.96" oled, 0.96 inch oled, oled 0.96, oled 0.96"
go top
close