Home Productos Pantalla OLED Pantalla OLED Gráfico WEO012832K

Displays OLED 2 pulgada, 128x32 puntos, SSD1315

Modelo Nº WEO012832K

►Tipo : Gráfico
►Estructura : COG
►Tamaño : 2 pulgada
►Matriz de puntos 128 x 32
►IC:SSD1315
►Fuente de alimentación de 3V
►1/32 duty
►Interfaz : 8 Bits 6800 8080/ SPI/ I2C
►Color de la pantalla: Blanco / Amarillo

Descripción

Se trata WEO012832K de una pantalla OLED COG que está hecha de 128x32 puntos, con un tamaño diagonal de 2 pulgadas. Este módulo tiene un tamaño de 59x18,86 mm y un tamaño de área activa de 50,535x10,695 mm. Este módulo está integrado con SSD1315 IC; es compatible con la interfaz 6800/8080, I2C y SPI de 4 cables.

Este pantalla de OLED 2 pulgada, voltaje de suministro para la lógica es de 2,8 V a 3,3 V, con un valor típico de 3 V. El voltaje de suministro para pantalla es de 8 V, con 1/32 de servicio de impulsión. Esta serie de módulo puede funcionar a temperaturas de -40 ℃ a +80 ℃ y su temperatura de almacenamiento oscila entre -40 ℃ y +85 ℃.

DIBUJO

2 inch 128x32 OLED Display Module - WEO012832K - Winstar

ESPECIFICACIONES

Función interfaz Pin

No. Símbolo Función
1 NC No connection
2 VCC Power supply for panel driving voltage. This is also the most positive power voltage supply pin.
When charge pump is enabled, a capacitor should be connected between this pin and VSS.
3 VCOMH COM signal deselected voltage level.
A capacitor should be connected between this pin and VSS.
4 IREF This is segment output current reference pin.
When external IREF is used, a resistor should be connected between this pin and VSS to maintain the IREF current at 30uA.
5 D7 These are 8-bit bi-directional data bus to be connected to the microprocessor’s data bus. When serial interface mode is selected, D0 will be the serial clock input: SCLK; D1 will be the serial data input: SDIN.
When I2C mode is selected, D2, D1 should be tied together and serve as SDAout, SDAin in application and D0 is the serial clock input, SCL.
6 D6
7 D5
8 D4
9 D3
10 D2
11 D1
12 D0
13 E/RD# This pin is MCU interface input.
When 6800 interface mode is selected, this pin will be used as the Enable (E) signal. Read/write operation is initiated when this pin is pulled HIGH and the chip is selected.
When 8080 interface mode is selected, this pin receives the Read (RD#) signal. Read operation is initiated when this pin is pulled LOW and the chip is selected.
When serial or I2C interface is selected, this pin must be connected to VSS.
14 R/W# This is read / write control input pin connecting to the MCU interface.
When interfacing to a 6800-series microprocessor, this pin will be used as Read/Write (R/W#) selection input. Read mode will be carried out when this pin is pulled HIGH (i.e. connect to VDD) and write mode when LOW.
When 8080 interface mode is selected, this pin will be the Write (WR#) input. Data write operation is initiated when this pin is pulled LOW and the chip is selected.
When serial or I2C interface is selected, this pin must be connected to VSS.
15 D/C# This pin is Data/Command control pin connecting to the MCU.
When the pin is pulled HIGH, the data at D[7:0] will be interpreted as data.
When the pin is pulled LOW, the data at D[7:0] will be transferred to a command register.
16 RES# This pin is reset signal input. When the pin is pulled LOW, initialization of the chip is executed. Keep this pin HIGH (i.e. connect to VDD) during normal operation.
17 CS# This pin is the chip select input connecting to the MCU.
The chip is enabled for MCU communication only when CS# is pulled LOW (active LOW).
18 NC No connection
19 BS2 MCU bus interface selection pins. Select appropriate logic setting as described in the following table. BS2, BS1 are pin select



Note
(1) 0 is connected to VSS
(2) 1 is connected to VDD
20 BS1
21 VDD Power supply pin for core logic operation.
This is a voltage supply pin. It must be connected to external source.
22~29 NC No connection
30 VSS Ground pin. It must be connected to external ground.
31 NC No connection

Datos mecánicos

Elemento Dimensión Unidad
Matriz de puntos 128 x 32 Dots
Dimensión del módulo 59.0 × 18.86 × 1.41 mm
zona activa 50.535 × 10.695 mm
Tamaño del punto 0.370 × 0.310 mm
Distancia entre puntos 0.395 × 0.335 mm
Modo de visualización Matriz pasiva
Color de la pantalla Monocromos
Interfaz 8Bits 6800 8080/ 4-Wire SPI/ I2C
Drive Duty 1/32 Duty
IC SSD1315
Tamaño 2 pulgada

Valores nominales máximos absolutos

Unless otherwise specified, VSS= 0 ( Ta = 25°C)
Parameter Símbolo Valor mín. Valor típico Valor máx. Unidad
Supply Voltage for Logic VDD -0.3 - 4 V
Supply Voltage for Display VCC 0 - 18 V
Temperatura de funcionamiento TOP -40 - +80 °C
Temperatura de almacenamiento TSTG -40 - +85 °C

Características electrónicas

Elemento Símbolo Valor mín. Valor típico Valor máx. Unidad
Supply Voltage Logic VDD 2.8 3.0 3.3 V
Operating VCC 7.5 8.0 8.5 V
Input Voltage High Voltage VIH 0.8 x VDD - VDD V
Low Voltage VIL 0 - 0.2 x VDD V
Output
Voltage
High Voltage VOH 0.9x VDD - VDD V
Low Voltage VOL 0 - 0.1 x VDD V
 
Symbol Parameter Valor mín. Valor típico Valor máx. Unidad Condición
ICC VCC Supply Current - 11 22 mA VDD=3V , VCC=8.0,
Display 50% ON
go top
close