首页 产品介绍 OLED显示屏 图形 OLED 显示屏 WEO012832K

128x32 图形点阵 SSD1315 2寸 OLED显示屏

型号 WEO012832K

►类型:点阵图形
►结构:COG
►尺寸:2寸
►128x32点阵
►IC:SSD1315
►3V电源电压
►1/32 duty
►接口: 8 Bits 6800 8080/ SPI/ I2C
►发光颜色: 白色 / 黄色

产品叙述

WEO012832K为2寸COG 带Hot Bar FPC结构的绘图型被动式OLED显示器模块,面板分辨率128x32 pixels。 WEO012832K模块内置SSD1315 IC,支持 6800/8080 8-bit 并行接口,I2C与4-线SPI接口,3V电压驱动,1/32 duty。此型号OLED模块可支持内部升压及外部供电。

WEO012832K与因为TAB IC EOL的WEX012832A产品AA区尺寸相同、PIN脚兼容、客户硬件不需修改,仅需修改Initial code,WEO012832K可视为WEX012832A替代方案。 WEO012832K是COG结构的OLED,无需背光非常轻薄 ,非常适用智能控制、工控仪器显示器、智能家电、智能医疗等产品。此模块的工作温度是-40℃至 80℃,储存温度-40℃至 85℃。

 

规格图

2 inch 128x32 OLED Display Module - WEO012832K - Winstar

产品规格

Pin功能定义

No. 符号 功能
1 NC No connection
2 VCC Power supply for panel driving voltage. This is also the most positive power voltage supply pin.
When charge pump is enabled, a capacitor should be connected between this pin and VSS.
3 VCOMH COM signal deselected voltage level.
A capacitor should be connected between this pin and VSS.
4 IREF This is segment output current reference pin.
When external IREF is used, a resistor should be connected between this pin and VSS to maintain the IREF current at 30uA.
5 D7 These are 8-bit bi-directional data bus to be connected to the microprocessor’s data bus. When serial interface mode is selected, D0 will be the serial clock input: SCLK; D1 will be the serial data input: SDIN.
When I2C mode is selected, D2, D1 should be tied together and serve as SDAout, SDAin in application and D0 is the serial clock input, SCL.
6 D6
7 D5
8 D4
9 D3
10 D2
11 D1
12 D0
13 E/RD# This pin is MCU interface input.
When 6800 interface mode is selected, this pin will be used as the Enable (E) signal. Read/write operation is initiated when this pin is pulled HIGH and the chip is selected.
When 8080 interface mode is selected, this pin receives the Read (RD#) signal. Read operation is initiated when this pin is pulled LOW and the chip is selected.
When serial or I2C interface is selected, this pin must be connected to VSS.
14 R/W# This is read / write control input pin connecting to the MCU interface.
When interfacing to a 6800-series microprocessor, this pin will be used as Read/Write (R/W#) selection input. Read mode will be carried out when this pin is pulled HIGH (i.e. connect to VDD) and write mode when LOW.
When 8080 interface mode is selected, this pin will be the Write (WR#) input. Data write operation is initiated when this pin is pulled LOW and the chip is selected.
When serial or I2C interface is selected, this pin must be connected to VSS.
15 D/C# This pin is Data/Command control pin connecting to the MCU.
When the pin is pulled HIGH, the data at D[7:0] will be interpreted as data.
When the pin is pulled LOW, the data at D[7:0] will be transferred to a command register.
16 RES# This pin is reset signal input. When the pin is pulled LOW, initialization of the chip is executed. Keep this pin HIGH (i.e. connect to VDD) during normal operation.
17 CS# This pin is the chip select input connecting to the MCU.
The chip is enabled for MCU communication only when CS# is pulled LOW (active LOW).
18 NC No connection
19 BS2 MCU bus interface selection pins. Select appropriate logic setting as described in the following table. BS2, BS1 are pin select



Note
(1) 0 is connected to VSS
(2) 1 is connected to VDD
20 BS1
21 VDD Power supply pin for core logic operation.
This is a voltage supply pin. It must be connected to external source.
22~29 NC No connection
30 VSS Ground pin. It must be connected to external ground.
31 NC No connection

规格说明

项目 规格 单位
分辨率 128 x 32 Dots
模块尺寸 59.0 × 18.86 × 1.41 mm
有效区域 50.535 × 10.695 mm
像素大小 0.370 × 0.310 mm
像素间距 0.395 × 0.335 mm
显示模式 被动矩阵
显示颜色 单色
接口 8Bits 6800 8080/ 4-Wire SPI/ I2C
驱动方式 1/32 Duty
IC SSD1315
尺寸 2寸

最大绝对额定值

Unless otherwise specified, VSS= 0 ( Ta = 25°C)
参数 符号 最小值 典型值 最大值 单位
逻辑电源电压 VDD -0.3 - 4 V
显示电源电压 VCC 0 - 18 V
工作温度 TOP -40 - +80 °C
储存温度 TSTG -40 - +85 °C

电气特性

项目 符号 最小值 典型值 最大值 单位
电源电压 Logic VDD 2.8 3.0 3.3 V
Operating VCC 7.5 8.0 8.5 V
输入电压 High Voltage VIH 0.8 x VDD - VDD V
Low Voltage VIL 0 - 0.2 x VDD V
输出电压 High Voltage VOH 0.9x VDD - VDD V
Low Voltage VOL 0 - 0.1 x VDD V
 
符号 参数 最小值 典型值 Max 单位 条件
ICC VCC Supply Current - 11 22 mA VDD=3V , VCC=8.0,
Display 50% ON
go top
close

我们重视您的隐私

通过点击「允许所有 Cookie」,代表您同意在您的设备上存储 Cookie 以增强网站浏览体验、分析网站使用情况并协助我们的营销和网站效能优化工作。您可以在我们的隐私权政策中找到有关于此的更多信息。

我们重视您的隐私

Winstar 及部分第三方在 www.winstar.com.tw 上使用 cookies。关于 cookie 的种类、用途及相关第三方的详细信息,请参见下文及我们的《Cookie 政策》。请点击“允许全部”来同意我们使用 cookies,以确保您在我们网站上获得最佳体验。您也可以设置您的偏好或拒绝 cookies(必要的 cookies 除外)。

管理同意声明

永久启用
必要的 Cookie

这些 Cookie 是必不可少的,以便让您在浏览网站并使用其功能上有更好地体验,例如设置您的隐私偏好、登录或填写窗体。

分析 Cookie

这些也被称为「统计cookie」,用于收集您使用网站的信息,例如您访问了哪些页面以及点击了哪些连结。查看详细信息