Home Products TFT Display Standard TFT Color Display WF57XTIACDNG0

5.7" PCAP Touch Panel TFT LCD Module

Model No. WF57XTIACDNG0

►Size : 5.7 inch
►Resolution : 320 x 240 dots
►View Direction : 12H
►Interface : RGB
►Driver IC:HX8218+HX8615
►Control-Board : Option
►Brightness(cd/m²): 700
►Frame Through Hole : No
►Touch Screen : Projected Capacitive Touch Panel (PCAP)
►Detect Point : 5 Fingers
►O-Film : Option

Description

The WF57XTIACDNG0 is a 5.7-inch TFT LCD with a projected capacitive touch panel (PCAP). It boasts a resolution of 320 x 240 dots and a brightness of 700 cd/m². The TFT display is powered by the HX8218+HX8615 driver IC, supporting 24-bit RGB interfaces. Its voltage power supply ranges from 3.2V to 3.4V. The module's dimensions are 126.00(W) × 101.55(H) mm, with an active area of 115.2 × 86.40 mm.

Equipped with a PCAP touch function and ILI2130 driver IC, the WF57XTIACDNG0 supports I2C interfaces and features 5-finger detection. It offers a 12 o'clock viewing direction, 6 o'clock gray scale inversion, and a 4:3 aspect ratio. Operating temperature ranges from -20℃ to +70℃, while storage temperature spans from -30℃ to +80℃.

A 5.7-inch touchscreen display is versatile and used in various sectors: Smart Home Control, Industrial Monitoring, Medical Diagnostics, In-Car Entertainment, Electronic Menus, Smart Handheld Devices, Agriculture Monitoring, Educational Displays, Traffic Signal Control, Mobile Payments.

DRAWING

5.7"  Projected Capacitive Touch Panel TFT LCD Module - WF57DTIACDNGE

SPECIFICATIONS

General Specifications

Item Dimension Unit
Size 5.7 inch
Dot Matrix 320 × RGB × 240 (TFT) dots
Module dimension 126.00(W) × 101.55(H) ×7.79(D) mm
Active area 115.2 × 86.40 mm
Dot pitch 0.12 × 0.36 mm
LCD type TFT, Normally White, Transmissive
View Direction 12 o'clock
Gray Scale Inversion Direction 6 o'clock
TFT Drive IC HX8218+HX8615 or Equivalent
Interface 24-bit RGB
Aspect Ratio 4:3
Backlight Type LED, Normally White
PCAP FW Version 0x07.0x00.0x00.0x00.0xA1.0x01.0x57.0x00
PCAP IC ILI2130 or equivalent
PCAP Interface I2C
PCAP Resolution 16384*16384
Touch Panel Projected Capacitive Touch Panel (PCAP)
Surface Glare

Absolute Maximum Ratings

Item Symbol Min Typ Max Unit
Operating Temperature TOP -20 +70
Storage Temperature TST -30 +80

Electrical Characteristics

1. Operating conditions:

Item Symbol Condition Min Typ Max Unit
Supply Voltage For LCM VCC - 3.2 3.3 3.4 V
AVDD   4.5 5.0 5.5 V
Supply PCAP VDDT - 3.1 3.3 3.5 V
ICTP - - 56 84 mA
Input High Volt. VIH - 0.7 VCC VCC V
Input Low Volt. VIL - 0 0.3 VCC V
LCD Driving Supply Voltage VGH *1 Ta=25℃ 15 16 17 V*3
VGL*2 -6 -5 -4
VcomH - 4.5 -
VcomL - -0.5 -
Supply Current For LCM IVCC VCC=3.3V - 30 45 mA
 

2. LED driving conditions

Parameter Symbol Min Typ Max Unit
LED current - - 140 - mA
Power Consumption - 1204 - 1470 mW
LED voltage VBL+ 8.6 9.5 10.5 V
LED Life Time - - 50,000 - Hr

Interface

LCM PIN Definition

Pin No. Symbol I/O Description
1 IF1 I Input data format control
2 IF2 I Input data format control
3 POL O Polarity Signal connect to VCOM driving circuit.
4 RESET I Hardware reset.
5 SPENA I Chip select
6 SPCL I Serial Clock
7 SPDA I/O Serial Data
8 B0 I Blue Data bit (LSB)
9 B1 I Blue Data bit
10 B2 I Blue Data bit
11 B3 I Blue Data bit
12 B4 I Blue Data bit
13 B5 I Blue Data bit
14 B6 I Blue Data bit
15 B7 I Blue Data bit(MSB)
16 G0 I Green Data bit(LSB)
17 G1 I Green Data bit
18 G2 I Green Data bit
19 G3 I Green Data bit
20 G4 I Green Data bit
21 G5 I Green Data bit
22 G6 I Green Data bit
23 G7 I Green Data bit(MSB)
24 R0 I Red Data bit(LSB)
25 R1 I Red Data bit
26 R2 I Red Data bit
27 R3 I Red Data bit
28 R4 I Red Data bit
29 R5 I Red Data bit
30 R6 I Red Data bit
31 R7 I Red Data bit(MSB)
32 Hsync I Horizontal synchronous signal
33 Vsync I Vertical synchronous signal
34 Data CLK I Dot data clock
35 AVDD I 4.5V~5.5V
36 AVDD I 4.5V~5.5V
37 Vcc I 3V~3.6V
38 Vcc I 3V~3.6V
39 NPC O NTSC/PAL mode Auto detection result H:NTSC/L:PAL
40 VGL I Gate off power
41 VGL I Gate off power
42 UD I Up/Down scan setting. H: Reverse scan / L: Normal scan
43 VGH I Gate on power
44 LRC I Shift direction of device internal shift register control.
45 GND I GROUND
46 VCOM I VCOM driving input
47 VCOM I VCOM driving input
48 ENB I Data enable input. Normally pull low.
49 GND I GROUND
50 GND I GROUND

Backlight PIN Definition

Pin No. Symbol I/O Description
1 VLED+ I Red, LED_ Anode
2 VLED- I Black, LED_ Cathode

PCAP PIN Definition

Pin Symbol Function
1 VSS Ground for analog circuit
2 VDDT Power Supply : +3.3V
3 SCL I2C clock input
4 NC No connect
5 SDA I2C data input and output
6 NC No connect
7 /RST External Reset, Low is active
8 NC No connect
9 /INT External interrupt to the host
10 VSS Ground for analog circuit
go top
close

We value your privacy

By clicking "Allow All Cookies", you agree to the storing of cookies on your device to enhance site navigation, analyse site usage, and assist in our marketing and performance efforts. You can find further information this subject in our policy.

We value your privacy

Winstar and certain third parties use cookies on www.winstar.com.tw. The details regarding the types of
cookies, their purpose and the third parties involved are described below and in our Cookie Policy.
Please click on “Allow All” to consent to our usage of cookies in order to have the best possible
experience on our websites. You can also set your preferences or reject cookies (except for strictly
necessary cookies).

Manage Consent Preferences

Always Active
Essential Cookies

These cookies are essential in order to enable you to move around the website and use its
features, such as setting your privacy preferences, logging in or filling in forms.

Analytics Cookies

Also known as “statistics cookies,” these cookies collect information about how you use a website, like which pages you visited and which links you clicked on. See Detail