Pantalla TFT PCAP Touch Screen 5.7"
Modelo Nº WF57XTIACDNG0
►Tamaño : 5.7”
►Resolución : 320 x 240 puntos
►Dirección de la vista : 12H
►Interfaz : RGB
►Driver IC:HX8218+HX8615
►Placa de control : Opcional
►Brillo (cd/m²) : 700
►Agujero del bastidor : No
►Pantalla táctil : Con panel táctil capacitivo (PCAP)
►Detect Point : 5 Fingers
►O-Film : Opcional
Descripción
El WF57XTIACDNG0 es un LCD TFT de 5.7 pulgadas con un panel táctil capacitivo proyectado (PCAP). Cuenta con una resolución de 320 x 240 puntos y un brillo de 700 cd/m². La pantalla TFT está alimentada por el circuito integrado del controlador HX8218+HX8615, que admite interfaces RGB de 24 bits. Su fuente de alimentación tiene un rango de voltaje de 3.2V a 3.4V. Las dimensiones del módulo son de 126.00 mm de ancho y 101.55 mm de alto, con un área activa de 115.2 × 86.40 mm.
Equipado con una función táctil PCAP y el circuito integrado del controlador ILI2130, el WF57XTIACDNG0 admite interfaces I2C y cuenta con detección de 5 dedos. Ofrece una dirección de visualización a las 12 en punto, inversión de escala de grises a las 6 en punto y una relación de aspecto de 4:3. La temperatura de funcionamiento varía desde -20℃ hasta +70℃, mientras que el rango de temperatura de almacenamiento abarca desde -30℃ hasta +80℃.
Un display táctil de 5.7 pulgadas es versátil y se utiliza en varios sectores: Control Inteligente del Hogar, Monitoreo Industrial, Diagnóstico Médico, Entretenimiento en el Automóvil, Menús Electrónicos, Dispositivos Portátiles Inteligentes, Monitoreo Agrícola, Exhibiciones Educativas, Control de Señales de Tráfico, Pagos Móviles.
DIBUJO
ESPECIFICACIONES
Función interfaz Pin
LCM PIN Definition
Pin No. | Símbolo | I/O | Función |
---|---|---|---|
1 | IF1 | I | Input data format control |
2 | IF2 | I | Input data format control |
3 | POL | O | Polarity Signal connect to VCOM driving circuit. |
4 | RESET | I | Hardware reset. |
5 | SPENA | I | Chip select |
6 | SPCL | I | Serial Clock |
7 | SPDA | I/O | Serial Data |
8 | B0 | I | Blue Data bit (LSB) |
9 | B1 | I | Blue Data bit |
10 | B2 | I | Blue Data bit |
11 | B3 | I | Blue Data bit |
12 | B4 | I | Blue Data bit |
13 | B5 | I | Blue Data bit |
14 | B6 | I | Blue Data bit |
15 | B7 | I | Blue Data bit(MSB) |
16 | G0 | I | Green Data bit(LSB) |
17 | G1 | I | Green Data bit |
18 | G2 | I | Green Data bit |
19 | G3 | I | Green Data bit |
20 | G4 | I | Green Data bit |
21 | G5 | I | Green Data bit |
22 | G6 | I | Green Data bit |
23 | G7 | I | Green Data bit(MSB) |
24 | R0 | I | Red Data bit(LSB) |
25 | R1 | I | Red Data bit |
26 | R2 | I | Red Data bit |
27 | R3 | I | Red Data bit |
28 | R4 | I | Red Data bit |
29 | R5 | I | Red Data bit |
30 | R6 | I | Red Data bit |
31 | R7 | I | Red Data bit(MSB) |
32 | Hsync | I | Horizontal synchronous signal |
33 | Vsync | I | Vertical synchronous signal |
34 | Data CLK | I | Dot data clock |
35 | AVDD | I | 4.5V~5.5V |
36 | AVDD | I | 4.5V~5.5V |
37 | Vcc | I | 3V~3.6V |
38 | Vcc | I | 3V~3.6V |
39 | NPC | O | NTSC/PAL mode Auto detection result H:NTSC/L:PAL |
40 | VGL | I | Gate off power |
41 | VGL | I | Gate off power |
42 | UD | I | Up/Down scan setting. H: Reverse scan / L: Normal scan |
43 | VGH | I | Gate on power |
44 | LRC | I | Shift direction of device internal shift register control. |
45 | GND | I | GROUND |
46 | VCOM | I | VCOM driving input |
47 | VCOM | I | VCOM driving input |
48 | ENB | I | Data enable input. Normally pull low. |
49 | GND | I | GROUND |
50 | GND | I | GROUND |
Backlight PIN Definition
Pin No. | Símbolo | I/O | Función |
---|---|---|---|
1 | VLED+ | I | Red, LED_ Anode |
2 | VLED- | I | Black, LED_ Cathode |
PCAP PIN Definition
Pin | Símbolo | Función |
---|---|---|
1 | VSS | Ground for analog circuit |
2 | VDDT | Power Supply : +3.3V |
3 | SCL | I2C clock input |
4 | NC | No connect |
5 | SDA | I2C data input and output |
6 | NC | No connect |
7 | /RST | External Reset, Low is active |
8 | NC | No connect |
9 | /INT | External interrupt to the host |
10 | VSS | Ground for analog circuit |
Especificaciones generales
Elemento | Dimensión | Unidad |
---|---|---|
Tamaño | 5.7 | pulgada |
Matriz de puntos | 320 × RGB × 240 (TFT) | puntos |
Dimensión del módulo | 126.00(W) × 101.55(H) ×7.79(D) | mm |
zona activa | 115.2 × 86.40 | mm |
Distancia entre puntos | 0.12 × 0.36 | mm |
Tipo de LCD | TFT, Blanco, Transmisivo | |
Dirección de la vista | 12 o'clock | |
Dirección de inversión de escala de grises | 6 o'clock | |
TFT Controlador IC | HX8218+HX8615 o equivalente | |
Interfaz | 24-bit RGB | |
Relación de aspecto | 4:3 | |
Tipo de retroiluminación | LED, Blanco | |
PCAP FW Version | 0x07.0x00.0x00.0x00.0xA1.0x01.0x57.0x00 | |
PCAP IC | ILI2130 o equivalente | |
PCAP interfaz | I2C | |
PCAP Resolución | 16384*16384 | |
Con o sin panel táctil | Con panel táctil capacitivo (PCAP) | |
Superficie | Deslumbramiento |
Valores nominales máximos absolutos
Elemento | Símbolo | Valor mín. | Valor típico | Valor máx. | Unidad |
---|---|---|---|---|---|
Temperatura de funcionamiento | TOP | -20 | - | +70 | ℃ |
Temperatura de almacenamiento | TST | -30 | - | +80 | ℃ |
Características electrónicas
1. Operating conditions:Elemento | Símbolo | Condición | Valor mín. | Valor típico | Valor máx | Unidad |
---|---|---|---|---|---|---|
Supply Voltage For LCM | VCC | - | 3.2 | 3.3 | 3.4 | V |
AVDD | 4.5 | 5.0 | 5.5 | V | ||
Supply PCAP | VDDT | - | 3.1 | 3.3 | 3.5 | V |
ICTP | - | - | 56 | 84 | mA | |
Input High Volt. | VIH | - | 0.7 VCC | - | VCC | V |
Input Low Volt. | VIL | - | 0 | - | 0.3 VCC | V |
LCD Driving Supply Voltage | VGH *1 | Ta=25℃ | 15 | 16 | 17 | V*3 |
VGL*2 | -6 | -5 | -4 | |||
VcomH | - | 4.5 | - | |||
VcomL | - | -0.5 | - | |||
Supply Current For LCM | IVCC | VCC=3.3V | - | 30 | 45 | mA |
2. LED driving conditions
Parameter | Símbolo | Valor mín. | Valor típico | Valor máx | Unidad |
---|---|---|---|---|---|
corriente LED | - | - | 140 | - | mA |
El consumo de energía | - | 1204 | - | 1470 | mW |
Voltaje LED | VBL+ | 8.6 | 9.5 | 10.5 | V |
Tiempo de vida del LED | - | - | 50,000 | - | Hr |