Home Products TFT LCD TFT Panel + Controller Board WF43QTIBEDBGF

4.3" PCAP TFT Panel with LCD Controller Board

Model No. WF43QTIBEDBGF

►Size : 4.3 inch
►Resolution : 480 x 272 dots
►View Direction : 12H
►Interface : MCU
►Controller IC:SSD1963
►Control-Board : Yes
►Brightness(cd/m²) : 400
►Frame Through Hole : Yes
►Touch Screen : Projected capacitive Touch Panel (PCAP)
►Detect Point : 5 Fingers
►O-Film : No

Description

The WF43QTIBEDBGF is a 4.3-inch capacitive touch TFT LCD display with a control board. It boasts a resolution of 480x272 pixels and an aspect ratio of 16:9. Equipped with an SSD1963 controller board, it offers interface options of 8-bit or 16-bit within the 8080 family MPU. Pin numbers 33 to 36 are designated for backlight supply, eliminating the need for an extra backlight circuit. The module features frame through holes for convenient mounting and usage.

The Winstar Q series supports the SSD1963 controller, which utilizes traditional inputs and drives TFT via VESA signals. Consequently, there is no need for a T-COM circuit onboard. Moreover, all functions, including TFT connection, backlight driver, and touch panel, are integrated into a single connection.

The WF43QTIBEDBGF module comes with a projected capacitive touch panel (PCAP) with an ILI2130 driver IC, supporting I2C interfaces and a 5-point touch function. The module's operating temperature ranges from -20°C to +70°C, and its storage temperature ranges from -30°C to +80°C. The LCM power supply voltage ranges from 3.0V to 3.3V, with a typical value of 3.1V. The brightness of the module is 400 nits, and the contrast ratio is 500:1 (typical value).

The Q series modules provide the following innovative advantages to offer outstanding performance for colorful displays:

  • Q Series integrated a 36 pin-out connector on SSD1963 controller board and all connectors are the same direction.
  • Q Series modules are available in 8 bit and 16 bit parallel interface options.
  • The pin no. 33 ~ 36 already pre-defined as backlight supply.
  • Built in backlight driver IC, Q series TFT displays can be drive by 5.0V (3.5" and 4.3" also support 3.3V). The customers do not have to change the backlight driver circuits while change the TFT module sizes.
  • The 5.7", 7.0", 8.0" and 10.2" Q Series are allowed to design "Sleep Mode" to close BIAS(VGH, VGL, AVDD) low power consumption mode.
  • Resistive touch screen options are available for all Q Series displays, and a 4-line signal (X1, Y1, X2, Y2) can be input from the 36-pin connector.
  • Projected Capacitive Touch Screen options are available for all Q Series display, and the I2C read/write protocol can be input from 36pin connector.

DRAWING

4.3 PCAP TFT Panel with LCD Controller Board - WF43QTIBEDBGF

SPECIFICATIONS

General Specifications

Item Dimension Unit
Size 4.3 inch
Dot Matrix 480 × RGB × 272(TFT) dots
Module dimension 106.7 × 83.98 × 8.6 mm
Active area 95.04 × 53.856 mm
Dot pitch 0.066 × 0.198 mm
LCD type TFT, Normally White, Transmissive
View Direction 12 o'clock
Gray Scale Inversion Direction 6 o'clock
Aspect Ratio 16:9
Backlight Type LED, Normally White
Controller IC SSD1963
TFT Interface Digital 8080 family MPU 8bit/16bit
PCAP FW Version 0x07.0x00.0x00.0x00.0x01.0x0C.0x11.0x43
PCAP IC ILI2130 or equivalent
PCAP Resolution 16384*16384
PCAP Interface I2C
Touch Panel Projected capacitive touch panel (PCAP)
Surface Glare

Absolute Maximum Ratings

Item Symbol Min Typ Max Unit
Operating Temperature TOP -20 +70
Storage Temperature TST -30 +80

Electrical Characteristics

Item Symbol Condition Min Typ Max Unit
Supply Voltage For LCM VDD 3.0 3.1 3.3 V
Supply Current For LCM IDD 210 350 mA

Interface

Pin Symbol Function
1 GND System round pin of the IC. Connect to system ground.
2 VDD Power Supply : +3.3V
3 BL_E Backlight control signal , H: On \ L: Off
4 D/C Data/Command select
5 WR Write strobe signal
6 RD Read strobe signal
7~14 D0~D7 Data bus
15~22 D8~D15 Data bus (When select 8bits mode, this pin is NC)
23 NC No connection
24 CTP_INT External interrupt to the host
25 CS Chip select
26 RESET Hardware reset
27 DIP ON Display control H: On \ L:Off
28 NC No connection
29 CTP_SCL Active low I2C clock input
30 CTP_SDA Data input I2C data input and output
31 CTP_RST External Reset, Low is active
32 NC No connection
33~34 VLED- VLED- for B/L LED inverter (GND)
35~36 VLED+ VLED+ for B/L LED inverter (+3.3V)
go top
close

We value your privacy

By clicking "Allow All Cookies", you agree to the storing of cookies on your device to enhance site navigation, analyse site usage, and assist in our marketing and performance efforts. You can find further information this subject in our policy.

We value your privacy

Winstar and certain third parties use cookies on www.winstar.com.tw. The details regarding the types of
cookies, their purpose and the third parties involved are described below and in our Cookie Policy.
Please click on “Allow All” to consent to our usage of cookies in order to have the best possible
experience on our websites. You can also set your preferences or reject cookies (except for strictly
necessary cookies).

Manage Consent Preferences

Always Active
Essential Cookies

These cookies are essential in order to enable you to move around the website and use its
features, such as setting your privacy preferences, logging in or filling in forms.

Analytics Cookies

Also known as “statistics cookies,” these cookies collect information about how you use a website, like which pages you visited and which links you clicked on. See Detail