2 inch IPS 240x320 TFT LCD Display with PCAP
Model No. WF0200BTYAJDNG10
►Size: 2 inch TFT LCD Display
►Resolution: 240×320 dots
►View Direction: IPS
►Interface: MCU, SPI
►Driver IC:ST7789VI
►Control-Board: No
►Brightness(cd/m²): 400
►Frame Through Hole: No
►Touch Screen : Projected Capacitive Touch Panel (PCAP),OCA
►Detect Point : 1 Finger
Description
WF0200BTYAJDNG10 is a 2-inch Portrait Mode IPS TFT-LCD with a resolution of 240x320 pixels. Built with ST7789VI driver IC, WF0200BTYAJDNG10 supports MCU and SPI interfaces. The PCAP touchscreen has the built-in IC GT911 and supports the I2C interface. Besides, the PCAP panel features OCA technology to increase its durability and present better optical clarity.
WF0200BTYAJDNG10 has a wide viewing angle of Left: 80/ Right: 80/ Up: 80/ Down: 80 degree, a contrast ratio of 800:1, a brightness of 400 nits, and an aspect ratio of 3:4. The supply voltage for analog is from 2.4V to 3.6V (the typical value is 3.3V). This TFT-LCD module can work under temperatures from -20℃ to +70℃, and its storage temperatures range from -30℃ to +80℃.
The 2-inch portrait mode TFT LCD display is suitable for a wide range of electronic devices, including measurement tools such as laser distance measuring instruments and air quality detectors, as well as testing equipment, sports watches, and other electronic devices. Our WF0200B TFT series offers the without-touch-panel option; please check out the webpage of WF0200BSYAJDNN0 for more information.
DRAWING
SPECIFICATIONS
Interface
LCM PIN Definition
NO | Symbol | Function | |||||||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
1 | GND | Ground | |||||||||||||||||||||||||||||||||||
2 | NC(YU) | No connection | |||||||||||||||||||||||||||||||||||
3 | NC(XL) | No connection | |||||||||||||||||||||||||||||||||||
4 | NC(YD) | No connection | |||||||||||||||||||||||||||||||||||
5 | NC(XR) | No connection | |||||||||||||||||||||||||||||||||||
6 | NC | No connection | |||||||||||||||||||||||||||||||||||
7 | VDD | Power supply | |||||||||||||||||||||||||||||||||||
8 | VDDI | Power Supply for I/O System. | |||||||||||||||||||||||||||||||||||
9 | TE | Tearing effect signal is used to synchronize MCU to frame memory writing. If not used, please let this pin open |
|||||||||||||||||||||||||||||||||||
10 | CSX | Chip selection pin Low enable. High disable. |
|||||||||||||||||||||||||||||||||||
11 | DCX(SCL) | (D/CX): This pin is used to select “Data or Command” in the parallel interface. DCX=’1’: display data or parameter. DCX=’0’: command data. (SCL): When SPI mode,This pin is used to be serial interface clock. |
|||||||||||||||||||||||||||||||||||
12 | WRX(D/CX) | Display data/command selection Second Data lane in 2 data lane serial interface. (WRX): Write enable in MCU parallel interface. (D/CX): When 4-SPI mode,This pin in 4-line serial interface If not used, please fix this pin at VDDI or GND. |
|||||||||||||||||||||||||||||||||||
13 | RDX | -Read enable in 8080 MCU parallel interface. -If not used, please fix this pin at VDDI or GND. |
|||||||||||||||||||||||||||||||||||
14~29 | DB0~DB15 | Data bus line | |||||||||||||||||||||||||||||||||||
30 | RESX | System reset pin. signal is active low |
|||||||||||||||||||||||||||||||||||
31 | IM0 | The MCU interface mode select.
|
|||||||||||||||||||||||||||||||||||
32 | IM1 | ||||||||||||||||||||||||||||||||||||
33 | IM2 | ||||||||||||||||||||||||||||||||||||
34~35 | DB16~DB17 | Data bus line | |||||||||||||||||||||||||||||||||||
36 | VLED- | Cathode of LED backlight. | |||||||||||||||||||||||||||||||||||
37 | VLED- | Cathode of LED backlight. | |||||||||||||||||||||||||||||||||||
38 | VLED+ | Anode of LED backlight. | |||||||||||||||||||||||||||||||||||
39 | NC(SDA) | When SPI mode, This pin is SPI interface input/output pin. The data is latched on the rising edge of the SCL signal. If not used(NC), please fix this pin at VDDI or GND level. |
|||||||||||||||||||||||||||||||||||
40 | NC | No connection |
PCAP PIN Definition
Pin | Symbol | Function |
---|---|---|
1 | VSS | Ground for analog circuit |
2 | VDDT | Power Supply : |
3 | SCL | I2C clock inputI2C clock input |
4 | NC | No connect |
5 | SDA | I2C data input and output |
6 | NC | No connect |
7 | /RST | External Reset, Low is active |
8 | NC | No connect |
9 | /INT | External interrupt to the host |
10 | VSS | Ground for analog circuit |
General Specifications
Item | Dimension | Unit |
---|---|---|
Size | 2 | inch |
Dot Matrix | 240 x RGB x 320(TFT) | dots |
Module dimension | 38.8(W) x 52.3(H) x3.8(D) | mm |
Active area | 30.60 x 40.80 | mm |
Pixel Pitch | 0.1275 x 0.1275 | mm |
LCD type | TFT, Normally Black, Transmissive | |
TFT Interface | MCU / SPI | |
TFT Driver IC | ST7789VI or Equivalent | |
Viewing angle | 80/80/80/80 (IPS) | |
Aspect Ratio | 3:4 | |
Backlight Type | LED, Normally White | |
PCAP Driver IC | GT911 or equivalent | |
PCAP Interface | I2C | |
PCAP FW | V92 | |
PCAP Resolution | 240 * 320 | |
Touch Panel | With PCAP | |
Surface | Glare |
Absolute Maximum Ratings
Item | Symbol | Min | Typ | Max | Unit |
---|---|---|---|---|---|
Operating Temperature | TOP | -20 | - | 70 | ℃ |
Storage Temperature | TST | -30 | - | 80 | ℃ |
Electronical Characteristics
Item | Symbol | Condition | Min | Typ | Max | Unit |
---|---|---|---|---|---|---|
Supply Voltage For Analog | VDD | - | 2.4 | 3.3 | 3.6 | V |
Interface Operation Voltage | VDDI | - | 1.65 | 1.8 | 3.6 | V |
Supply Current For LCM | IDD | VDD = VDDI = VCC=3.0V |
- | 6.0 | 9.0 | mA |
Supply PCAP | VPCAP | - | 2.8 | - | 3.3 | V |
IPCAP | - | - | 8.0 | 12.0 | mA |
Search keyword: tft 2", 2 tft lcd, 2" tft lcd, 2 inch tft lcd, tft lcd 2, 2 tft display, 2" tft display, 2 inch tft display, tft display 2"