我们重视您的隐私
通过点击「允许所有 Cookie」,代表您同意在您的设备上存储 Cookie 以增强网站浏览体验、分析网站使用情况并协助我们的营销和网站效能优化工作。您可以在我们的隐私权政策中找到有关于此的更多信息。
WF0200BTYAJDNG10是一款2寸电容式触控 IPS TFT LCD 显示器模块,分辨率为240x320像素。模块内建ST7789VI驱动IC,支持MCU 和SPI接口传输,触控面板内建 GT911 IC 可支持I2C界面。WF0200B系列另有无触控面板模块,此外,PCAP 面板采用 OCA 技术以提高其耐用性并呈现更好的光学清晰度。
此款模块采用IPS面板,具有更宽广视角的优势,视角左:80/右:80/上:80/下:80度(典型值),对比度 800:1(典型值),亮度400 nits(典型值),长宽比3:4,供电电压为2.4V~3.6V,典型值为3.3V。此模块可在-20℃~+70℃温度范围下作业;储存温度范围-30℃~+80℃。
2寸直屏TFT液晶显示器适用于多种电子设备,包括雷射测距仪、空气质量侦测仪等测量工具,以及侦测设备、运动手表和其他电子设备。我们的 WF0200B TFT 系列提供无触摸面板选项; 请查看 WF0200BSYAJDNN0 的网页了解更多信息。
项目 | 规格 | 单位 |
---|---|---|
显示尺寸(对角线) | 2 | 寸 |
点阵(分辨率) | 240 x RGB x 320(TFT) | dots |
模块尺寸 | 38.8(W) x 52.3(H) x3.8(D) | mm |
有效区域 | 30.60 x 40.80 | mm |
像素间距 | 0.1275 x 0.1275 | mm |
LCD类型 | TFT全透 | |
TFT介面 | MCU / SPI | |
TFT驱动 IC | ST7789VI 或相容IC | |
视角 | 80/80/80/80 (IPS) | |
长宽比 | 3:4 | |
背光类型 | LED, 白色 | |
PCAP驱动IC | GT911或相容IC | |
PCAP介面 | I2C | |
FW版本 | V92 | |
PCAP分辨率 | 240 * 320 | |
触控面板类型 | PCAP电容式触控面板 | |
表面 | 亮面 |
项目 | 符号 | 最小值 | 典型值 | 最大值 | 单位 |
---|---|---|---|---|---|
工作温度 | TOP | -20 | - | 70 | ℃ |
储存温度 | TST | -30 | - | 80 | ℃ |
项目 | 符号 | 条件 | 最小值 | 典型值 | 最大值 | 单位 |
---|---|---|---|---|---|---|
模拟电源电压 | VDD | - | 2.4 | 3.3 | 3.6 | V |
接口工作电压 | VDDI | - | 1.65 | 1.8 | 3.6 | V |
LCM供电电流 | IDD | VDD = VDDI = VCC=3.0V |
- | 6.0 | 9.0 | mA |
Supply PCAP | VPCAP | - | 2.8 | - | 3.3 | V |
IPCAP | - | - | 8.0 | 12.0 | mA |
NO | 符号 | 功能说明 | |||||||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
1 | GND | Ground | |||||||||||||||||||||||||||||||||||
2 | NC(YU) | No connection | |||||||||||||||||||||||||||||||||||
3 | NC(XL) | No connection | |||||||||||||||||||||||||||||||||||
4 | NC(YD) | No connection | |||||||||||||||||||||||||||||||||||
5 | NC(XR) | No connection | |||||||||||||||||||||||||||||||||||
6 | NC | No connection | |||||||||||||||||||||||||||||||||||
7 | VDD | Power supply | |||||||||||||||||||||||||||||||||||
8 | VDDI | Power Supply for I/O System. | |||||||||||||||||||||||||||||||||||
9 | TE | Tearing effect signal is used to synchronize MCU to frame memory writing. If not used, please let this pin open |
|||||||||||||||||||||||||||||||||||
10 | CSX | Chip selection pin Low enable. High disable. |
|||||||||||||||||||||||||||||||||||
11 | DCX(SCL) | (D/CX): This pin is used to select “Data or Command” in the parallel interface. DCX=’1’: display data or parameter. DCX=’0’: command data. (SCL): When SPI mode,This pin is used to be serial interface clock. |
|||||||||||||||||||||||||||||||||||
12 | WRX(D/CX) | Display data/command selection Second Data lane in 2 data lane serial interface. (WRX): Write enable in MCU parallel interface. (D/CX): When 4-SPI mode,This pin in 4-line serial interface If not used, please fix this pin at VDDI or GND. |
|||||||||||||||||||||||||||||||||||
13 | RDX | -Read enable in 8080 MCU parallel interface. -If not used, please fix this pin at VDDI or GND. |
|||||||||||||||||||||||||||||||||||
14~29 | DB0~DB15 | Data bus line | |||||||||||||||||||||||||||||||||||
30 | RESX | System reset pin. signal is active low |
|||||||||||||||||||||||||||||||||||
31 | IM0 | The MCU interface mode select.
|
|||||||||||||||||||||||||||||||||||
32 | IM1 | ||||||||||||||||||||||||||||||||||||
33 | IM2 | ||||||||||||||||||||||||||||||||||||
34~35 | DB16~DB17 | Data bus line | |||||||||||||||||||||||||||||||||||
36 | VLED- | Cathode of LED backlight. | |||||||||||||||||||||||||||||||||||
37 | VLED- | Cathode of LED backlight. | |||||||||||||||||||||||||||||||||||
38 | VLED+ | Anode of LED backlight. | |||||||||||||||||||||||||||||||||||
39 | NC(SDA) | When SPI mode, This pin is SPI interface input/output pin. The data is latched on the rising edge of the SCL signal. If not used(NC), please fix this pin at VDDI or GND level. |
|||||||||||||||||||||||||||||||||||
40 | NC | No connection |
Pin | 符号 | 功能说明 |
---|---|---|
1 | VSS | Ground for analog circuit |
2 | VDDT | Power Supply : |
3 | SCL | I2C clock inputI2C clock input |
4 | NC | No connect |
5 | SDA | I2C data input and output |
6 | NC | No connect |
7 | /RST | External Reset, Low is active |
8 | NC | No connect |
9 | /INT | External interrupt to the host |
10 | VSS | Ground for analog circuit |
通过点击「允许所有 Cookie」,代表您同意在您的设备上存储 Cookie 以增强网站浏览体验、分析网站使用情况并协助我们的营销和网站效能优化工作。您可以在我们的隐私权政策中找到有关于此的更多信息。