На главную страницу Продукция OLED Дисплей Графический OLED дисплей WEF012864H

128x64, 2.42" дюймовый COG+FR OLED

Артикул. WEF012864H

►Тип: Графический (С рамкой)
►Тип монтажа контроллера: COG+FR
►Диагональ: 2.42 дюйма
►Разрешение: 128x64 точек
►IC:SSD1309
►3V Power supply
►1/64 duty
►Интерфейс: 6800, 8080, SPI, I2C
►Цвет дисплея: Белый / Желтый / Небесно голубой / Зеленый

Описание

WEF012864H – 2.4" дюймовый COG OLED модуль с пассивной матрицей и разрешением 128x64 точки. Дисплей WEF012864H сделан на базе контроллера IC SSD1309 c поддержкой интерфейсов: параллельного 6800/8080 8-Бит, I2C и четырехжильного SPI интерфейса. Напряжение питания 3V, а рабочий цикл 1/32. OLED дисплей WEF012864H это 2-я версия индикатора WEO012864G, где отличительной чертой является наличие монтажной рамки. Ультратонкий OLED дисплей WEF012864H имеет COG структуру и не нуждается в подсветке, за счет чего имеет легкий вес. Этот 2.4''-дюймовый OLED модуль подходит для: промышленных приборов, измерительных приборов, POS систем, Облачных/IoT систем, умных устройств, автомобилестроения, коммуникационных систем, медицинских устройств и т.д. WEF012864H может работать при температурах от -40 ° С до + 80 ℃; а температура хранения - от -40 ℃ до + 85 ℃.

Чертеж

WEF012864H
Data source ref:WEF012864HWPP3N00F00

Технические характеристики

Функции контроллера контактного интерфейса

Pin No. Символы Описание
1 NC(Vss) No connection (ground.)
2 VCC Power supply for panel driving voltage. This is also the most positive power voltage supply pin.
3 VCOMH COM signal deselected voltage level.
A capacitor should be connected between this pin and VSS.
4 IREF This pin is the segment output current reference pin.
IREF is supplied externally.
A resistor should be connected between this pin and VSS to maintain the current around 10uA. Please refer to Figure 8-15 for the details of resistor value
5~12 D7~D0 These pins are bi-directional data bus connecting to the MCU data bus.
Unused pins are recommended to tie LOW.
When serial interface mode is selected, D0 will be the serial clock input: SCLK; D1 will be the serial data input: SDIN and D2 should be kept NC.
When I2C mode is selected, D2, D1 should be tied together and serve as SDAout, SDAin in application and D0 is the serial clock input, SCL.
13 E/RD# This pin is MCU interface input.
When 6800 interface mode is selected, this pin will be used as the Enable (E) signal.
Read/write operation is initiated when this pin is pulled HIGH and the chip is selected.
When 8080 interface mode is selected, this pin receives the Read (RD#) signal. Read operation is initiated when this pin is pulled LOW and the chip is selected.
When serial or I2C interface is selected, this pin must be connected to VSS.
14 R/W# This pin is read / write control input pin connecting to the MCU interface.
When 6800 interface mode is selected, this pin will be used as Read/Write (R/W#)
selection input. Read mode will be carried out when this pin is pulled HIGH and
write mode when LOW.
When 8080 interface mode is selected, this pin will be the Write (WR#) input. Data
write operation is initiated when this pin is pulled LOW and the chip is selected.
When serial or I2C interface is selected, this pin must be connected to VSS.
15 D/C# This pin is Data/Command control pin connecting to the MCU.
When the pin is pulled HIGH, the data at D[7:0] will be interpreted as data.
When the pin is pulled LOW, the data at D[7:0] will be transferred to a command
register.
In I2C mode, this pin acts as SA0 for slave address selection.
When 3-wire serial interface is selected, this pin must be connected to VSS.
For detail relationship to MCU interface signals, refer to Timing Characteristics
16 RES# This pin is reset signal input.
When the pin is pulled LOW, initialization of the chip is executed.
Keep this pin pull HIGH during normal operation.
17 CS# This pin is the chip select input connecting to the MCU.
The chip is enabled for MCU communication only when CS# is pulled LOW (active
LOW).
18 NC No connection
19 BS2 MCU bus interface selection pins. Select appropriate logic setting as described in the
following table.

Note
(1) 0 is connected to VSS
(2) 1 is connected to VDD
20 BS1
21 Vdd Power supply pin for core logic operation
22~28 NC No connection
29 Vss Ground pin. It must be connected to external ground.
30 NC(Vss) No connection (ground.)

Механические характеристики

Наименование Измерения Единица
Разрешение 128 × 64 точек
Габариты 77.2 × 42.14 ×3.4 mm
Активная область 55.01 × 27.49 mm
Размер пикселя 0.40 × 0.40 mm
Шаг пикселя 0.43 × 0.43 mm
Матрица Пассивная
Цвет дисплея монохромные
Рабочий цикл 1/64 Duty
IC SSD1309
Интерфейс 6800,8080,SPI,I2C
Диагональ 2.42 дюйма

Абсолютные максимальные значения

Parameter Символы Минимальный Максимальный Единица
Напряжение питания логических схем VDD -0.3 4 V
Напряжение питания дисплея VCC 0 15 V
Диапазон рабочих температур TOP -40 +80 °C
Температура хранения TSTG -40 +85 °C

Электронные характеристики

DC Электронные характеристики

Наименование Символы Кондиция Минимальный Типичный Максимальный Единица
Напряжение питания логических схем VDD 2.8 3.0 3.3 V
Напряжение питания дисплея VCC 12.5 13.0 13.5 V
Вход высокого уровня VIH 0.8×VDD VDD V
Вход низкого уровня VIL 0 0.2×VDD V
Выход высокого уровня VOH 0.9×VDD VDD V
Выход низкого уровня VOL 0 0.1×VDD V
50% Check Board operating Current VCC =13V - 29 43.5 mA

Search keyword: 128x64 oled, oled 128x64, 2.42 oled, 2.42 дюйма oled, oled 2.42
go top
close