Home Productos Pantalla OLED Pantalla OLED Gráfico WEF012864H

Pantalla de OLED COG+FR 2.7" 128x64

Modelo Nº WEF012864H

►Tipo : Gráfico (con marco)
►Estructura : COG+FR
►Tamaño : 2.42 pulgada
►Matriz de puntos 128x64
►IC:SSD1309
►Fuente de alimentación de 3V
►1/64 duty
►Interfaz : 6800, 8080, SPI, I2C
►Color de la pantalla: Blanco / Amarillo / Azul cielo / Verde

DIBUJO

WEF012864H
Data source ref:WEF012864HWPP3N00F00

ESPECIFICACIONES

Función interfaz Pin

Pin No. Símbolo Función
1 NC(Vss) No connection (ground.)
2 VCC Power supply for panel driving voltage. This is also the most positive power voltage supply pin.
3 VCOMH COM signal deselected voltage level.
A capacitor should be connected between this pin and VSS.
4 IREF This pin is the segment output current reference pin.
IREF is supplied externally.
A resistor should be connected between this pin and VSS to maintain the current around 10uA. Please refer to Figure 8-15 for the details of resistor value
5~12 D7~D0 These pins are bi-directional data bus connecting to the MCU data bus.
Unused pins are recommended to tie LOW.
When serial interface mode is selected, D0 will be the serial clock input: SCLK; D1 will be the serial data input: SDIN and D2 should be kept NC.
When I2C mode is selected, D2, D1 should be tied together and serve as SDAout, SDAin in application and D0 is the serial clock input, SCL.
13 E/RD# This pin is MCU interface input.
When 6800 interface mode is selected, this pin will be used as the Enable (E) signal.
Read/write operation is initiated when this pin is pulled HIGH and the chip is selected.
When 8080 interface mode is selected, this pin receives the Read (RD#) signal. Read operation is initiated when this pin is pulled LOW and the chip is selected.
When serial or I2C interface is selected, this pin must be connected to VSS.
14 R/W# This pin is read / write control input pin connecting to the MCU interface.
When 6800 interface mode is selected, this pin will be used as Read/Write (R/W#)
selection input. Read mode will be carried out when this pin is pulled HIGH and
write mode when LOW.
When 8080 interface mode is selected, this pin will be the Write (WR#) input. Data
write operation is initiated when this pin is pulled LOW and the chip is selected.
When serial or I2C interface is selected, this pin must be connected to VSS.
15 D/C# This pin is Data/Command control pin connecting to the MCU.
When the pin is pulled HIGH, the data at D[7:0] will be interpreted as data.
When the pin is pulled LOW, the data at D[7:0] will be transferred to a command
register.
In I2C mode, this pin acts as SA0 for slave address selection.
When 3-wire serial interface is selected, this pin must be connected to VSS.
For detail relationship to MCU interface signals, refer to Timing Characteristics
16 RES# This pin is reset signal input.
When the pin is pulled LOW, initialization of the chip is executed.
Keep this pin pull HIGH during normal operation.
17 CS# This pin is the chip select input connecting to the MCU.
The chip is enabled for MCU communication only when CS# is pulled LOW (active
LOW).
18 NC No connection
19 BS2 MCU bus interface selection pins. Select appropriate logic setting as described in the
following table.

Note
(1) 0 is connected to VSS
(2) 1 is connected to VDD
20 BS1
21 Vdd Power supply pin for core logic operation
22~28 NC No connection
29 Vss Ground pin. It must be connected to external ground.
30 NC(Vss) No connection (ground.)

Especificaciones generales

Elemento Dimensión Unidad
Matriz de puntos (Resolución) 128 × 64 puntos
Dimensión del módulo 77.2 × 42.14 ×3.4 mm
zona activa 55.01 × 27.49 mm
Tamaño del punto 0.40 × 0.40 mm
Distancia entre puntos 0.43 × 0.43 mm
Modo de visualización Matriz pasiva
Color de la pantalla Monocromos
Drive Duty 1/64 Duty
IC SSD1309
Interfaz 6800,8080,SPI,I2C
Tamaño (Diagonal) 2.42 pulgada

Valores nominales máximos absolutos

Parameter Símbolo Valor mín. Valor máx. Unidad
Supply Voltage for Logic VDD -0.3 4 V
Supply Voltage for Display VCC 0 15 V
Temperatura de funcionamiento TOP -40 +80 °C
Temperatura de almacenamiento TSTG -40 +85 °C

Características electrónicas

DC Características electrónicas

Elemento Símbolo Condición Valor mín. Valor típico Valor máx. Unidad
Supply Voltage for Logic VDD 2.8 3.0 3.3 V
Supply Voltage for Display VCC 12.5 13.0 13.5 V
High Level Input VIH 0.8×VDD VDD V
Low Level Input VIL 0 0.2×VDD V
High Level Output VOH 0.9×VDD VDD V
Low Level Output VOL 0 0.1×VDD V
50% Check Board operating Current VCC =13V - 29 43.5 mA

Search keyword: 128x64 oled, oled 128x64, 2.42 oled, 2.42 pulgada oled, oled 2.42
go top
close