Model No. WEO009616A
►Type: Graphic (Without Frame)
►Structure: COG
►Size: 0.84 inch
►96 x 16 Dot Matrix
►IC：SSD1306
►3V Power supply
►1/16 duty
►Interface: I2C
►Display Color: White / Yellow / Sky Blue
►Suitable for Wearable Device
WEO009616A is a 0.84 inch Graphic passive matrix OLED display module which is made of 96x16 dots. This 0.84" WEO009616A has the module dimension of 29.1× 9.2 × 1.45 mm and Active Area size 21.104×3.504 mm. WEO009616A is built in with SSD1306 IC, it supports I2C interface, 3V power supply. The WEO009616A is a COG structure OLED display which is ultra thin and no need of backlight (self emitting); it's lightweight and low power consumption. This 0.84 inch small sized OLED display is suitable for wearable device, E-cigarette, MP3, personal care appliance, portable device, voice recorder pen, health device, etc. WEO009616A module can be operating at temperatures from -40℃ to +80℃; its storage temperatures range from -40℃ to +85℃. Below is the basic specification of WEO009616A as reference.WEO009616A module supports internal Charge Pump supply and external VCC supply.
Data source ref: WEO009616AWPP3N00000
| Item | Dimension | Unit |
|---|---|---|
| Dot Matrix | 96 x 16 Dots | － |
| Module dimension | 29.1× 9.2 × 1.26 | mm |
| Active Area | 21.104 × 3.504 | mm |
| Pixel Size | 0.198 × 0.198 | mm |
| Pixel Pitch | 0.220 × 0.220 | mm |
| Display Mode | Passive Matrix | |
| Display Color | Monochrome | |
| Drive Duty | 1/16 Duty | |
| IC | SSD1306 | |
| Interface | I2C | |
| Size | 0.84 inch | |
| Parameter | Symbol | Min | Max | Unit |
|---|---|---|---|---|
| Supply Voltage for Logic | VDD | 0 | 4.0 | V |
| Supply Voltage for Display | VCC | 0 | 16.0 | V |
| Operating Temperature | TOP | -40 | +80 | °C |
| Storage Temperature | TSTG | -40 | +85 | °C |
| Item | Symbol | Condition | Min | Typ | Max | Unit |
|---|---|---|---|---|---|---|
| Supply Voltage for Logic | VDD | － | 1.65 | 3.0 | 3.3 | V |
| Supply Voltage for Display (Supplied Externally) | VCC | － | 7.0 | 7.5 | 7.8 | V |
| Charge Pump Regulator Supply Voltage | VBAT | － | 3.3 | － | 4.2 | V |
| Charge Pump Output Voltage for Display (Generated by Internal DC/DC) | Charge Pump VCC |
－ | 7.0 | 7.5 | 7.8 | V |
| Input High Volt. | VIH | － | 0.8×VDD | － | VDD | V |
| Input Low Volt. | VIL | － | 0 | － | 0.2×VDD | V |
| Output High Volt. | VOH | － | 0.9×VDD | － | VDD | V |
| Output Low Volt. | VOL | － | 0 | － | 0.1×VDD | V |
| 50% check Board operating Current (VCC Supplied Externally) | ICC | － | － | 7 | 15 | mA |
| 50% check Board operating Current (VCC Generated by Internal DC/DC) | IBAT | － | 10 | 15 | 25 | mA |
| No. | Symbol | Function |
|---|---|---|
| 1 | C2N | Positive Terminal of the Flying Inverting CapacitorNegative Terminal of the Flying Boost Capacitor The charge-pump capacitors are required between the terminals. They must be floated when the converter is not used. |
| 2 | C2P | |
| 3 | C1P | |
| 4 | C1N | |
| 5 | VBAT | Power Supply for DC/DC Converter Circuit This is the power supply pin for the internal buffer of the DC/DC voltage converter. It must be connected to external source when the converter is used. It should be connected to VDD when the converter is not used. |
| 6 | NC | No connection |
| 7 | VSS | Ground of Logic Circuit This is a ground pin. It acts as a reference for the logic pins. It must be connected to external ground. |
| 8 | VDD | Power Supply for Logic This is a voltage supply pin. It must be connected to external source. |
| 9 | RES# | Power Reset for Controller and Driver This pin is reset signal input. When the pin is low, initialization of the chip is executed. |
| 10 | SCL | I2C mode is selected, D2, D1 should be tied together and serve as SDAout, SDAin inapplication and D0 is the serial clock input, SCL. |
| 11 | SDA | |
| 12 | IREF | Current Reference for Brightness Adjustment This pin is segment current reference pin. A resistor should be connected between this pin and VSS. Set the current lower than 30uA. |
| 13 | VCOMH | Voltage Output High Level for COM Signal This pin is the input pin for the voltage output high level for COM signals. A capacitor should be connected between this pin and VSS. |
| 14 | VCC | Power Supply for OEL Panel This is the most positive voltage supply pin of the chip. A stabilization capacitor should be connected between this pin and VSS when the converter is used. It must be connected to external source when the converter is not used. |
By clicking "Allow All Cookies", you agree to the storing of cookies on your device to enhance site navigation, analyse site usage, and assist in our marketing and performance efforts. You can find further information this subject in our policy.