Model No. WF35UTYAIDNN0
►Size : 3.5"
►Resolution : 320×480 dots
►View Direction : IPS
►Interface : MCU 8/16/18-bit, 3-SPI ,RGB interface+3-SPI
►Driver IC：ILI9488
►Control-Board :No
►Brightness(cd/m²) : 600
►Frame Through Hole : No
►Touch Screen : Without touch panel
WF35UTYAIDNN0 is a 3.5 inch IPS Panel with 320x480 resolution TFT LCD module. This module is built in with ILI9488 IC; it supports MCU, 3-Line SPI interface / RGB interface+3-SPI and featured with brightness 600 nits (typical value).
This 3.5” TFT LCD module is portrait mode with IPS (In-Plane Switching) Panel which having the advantages of wider viewing angle of Left:80 / Right:80 / Up:80 / Down:80 degree (typical). WF35UTYAIDNN0 module can be operating at temperatures from -20℃ to +70℃; its storage temperatures range from -30℃ to +80℃.
| Item | Dimension | Unit |
|---|---|---|
| Size | 3.5 | inch |
| Dot Matrix | 320 × RGB × 480(TFT) | dots |
| Module dimension | 54.5 (W) × 83.0 (H) × 2.46(D) | mm |
| Active area | 48.96 × 73.44 | mm |
| Pixel pitch | 0.153 × 0.153 | mm |
| LCD type | TFT, Normally Black, Transmissive | |
| View Direction | 80/80/80/80 | |
| Aspect Ratio | Portrait | |
| Driver IC | ILI9488 | |
| Interface | MCU 8/16/18-bit, 3-SPI ,RGB interface+3-SPI | |
| Backlight Type | LED, Normally White | |
| Touch Panel | Without Touch Panel | |
| Surface | Anti-Glare | |
| Item | Symbol | Min | Typ | Max | Unit |
|---|---|---|---|---|---|
| Operating Temperature | TOP | -20 | － | 70 | ℃ |
| Storage Temperature | TST | -30 | － | 80 | ℃ |
| Item | Symbol | Condition | Min | Typ | Max | Unit |
|---|---|---|---|---|---|---|
| Supply Voltage for digital | IOVCC | － | － | 1.8/2.8 | 3.3 | V |
| Supply Voltage for analog | VCI | － | － | 2.8 | 3.3 | V |
| Power Supply for Current | ICC | IOVCC=VCI =VCC=3.3V |
－ | 13.6 | － | mA |
| NO | Symbol | Function | I/O |
|---|---|---|---|
| 1 | LEDK | Cathode of LED backlight | P |
| 2 | LEDA | Anode of LED backlight. | P |
| 3 | IM0 | Note 1 | I |
| 4 | IM1 | Note 1 | I |
| 5 | IM2 | Note 1 | I |
| 6 | RESET | System reset pin. | I |
| 7 | NC(VS) | No Connection (Vrtical Sync signal) Note 2) | I |
| 8 | NC(HS) | No Connection (Horizontal Sync signal ; Note 2) | I |
| 9 | NC(DCLK) | No Connection (Pixel clock signal; Note 2) | I |
| 10 | NC(DE) | No Connection (Data Enable; Note 2) | I |
| 11-16 | DB17-12 | Data bus (R5~R0; RGB-18bit Pixel; Note 2) | I |
| 17-22 | DB11-6 | Data bus (G5~G0; RGB-18bit Pixel; Note 2) | I |
| 23-28 | DB5-0 | Data bus (B5~B0; RGB-18bit Pixel; Note 2) | I |
| 29 | NC (SDA) | Connection (serial data input/output pin) | I |
| 30 | RD | Read strobe signal. Read out data when RDX is Low. | I |
| 31 | WR (SCL) | Write data when WRX is Low.(serial clock input pin) | I |
| 32 | D/C | register select | I |
| 33 | CS (NCS) | Chip select signal (serial chip select input pin) | I |
| 34 | IOVCC | Power supply (TYP:1.8V/2.8V). | P |
| 35 | VCI | Power supply(TYP:2.8V). | P |
| 36 | GND | Ground | P |
| 37 | NC | No connection | |
| 38 | NC | No connection | |
| 39 | NC | No connection | |
| 40 | NC | No connection |
| IM2 | IM1 | IM0 | MPU Interface | GRAM |
|---|---|---|---|---|
| 0 | 0 | 0 | 8080 MCU 18-bit bus | D[17:0] |
| 0 | 1 | 0 | 8080 MCU 16-bit bus | D[15:0] |
| 0 | 1 | 1 | 8080 MCU 8-bit bus | D[7:0] |
| 1 | 0 | 1 | 3-Line SPI | SDA,SCL,NCS |
| 1 | 0 | 1 | RGB interface+3-SPI | D[17:0] (RGB-18bit/Pixel) D[15:0] (RGB-16bit/Pixel) |
Note 2:
This module suggests function is for 8080 MCU mode, if this module wants change to use RGB Interface mode, please setting external pin IM [2:0] as 101 (3-SPI Initial code setting RGB-18bit/Pixel or RGB-16bit/Pixel),and reference the 7.5. RGB Interface Selection
By clicking "Allow All Cookies", you agree to the storing of cookies on your device to enhance site navigation, analyse site usage, and assist in our marketing and performance efforts. You can find further information this subject in our policy.
