Model No. WF35UTYAIMNN0
►Size : 3.5"
►Resolution : 320×480 dots
►View Direction : IPS
►Interface : 1-Lane MIPI
►IC : ILI9488
►Control-Board :No
►Brightness(cd/m²) : 600
►Frame Through Hole : No
►Touch Screen : Without touch panel
WF35UTYAIMNN0 is a 3.5-inch TFT LCD module with an IPS panel. This module is integrated with the ILI9488 driver IC, supporting 1-Lane MIPI interfaces. This portrait mode display has a resolution of 320×480 pixels, with a typical brightness of 600 nits and a contrast ratio of 700:1.
The IPS panel offers the advantage of wide viewing angles, with a typical range of Left: 80°, Right: 80°, Up: 80°, and Down: 80°. The WF35UTYAIMNN0 can operate in temperatures ranging from -20℃ to +70℃, and its storage temperature range is from -30℃ to +80℃.
| Item | Dimension | Unit |
|---|---|---|
| Size | 3.5 | inch |
| Dot Matrix | 320 × RGB × 480(TFT) | dots |
| Module dimension | 54.5 (W) × 83.0 (H) × 2.46(D) | mm |
| Active area | 48.96 × 73.44 | mm |
| Pixel pitch | 0.153 × 0.153 | mm |
| LCD type | TFT, Normally Black, Transmissive | |
| View Direction | 80/80/80/80 | |
| Aspect Ratio | Portrait | |
| Driver IC | ILI9488 | |
| Interface | 1-Lane MIPI | |
| Backlight Type | LED, Normally White | |
| Touch Panel | Without Touch Panel | |
| Surface | Anti-Glare | |
| Item | Symbol | Min | Typ | Max | Unit |
|---|---|---|---|---|---|
| Operating Temperature | TOP | -20 | － | 70 | ℃ |
| Storage Temperature | TST | -30 | － | 80 | ℃ |
| Item | Symbol | Condition | Min | Typ | Max | Unit |
|---|---|---|---|---|---|---|
| Supply Voltage for digital | IOVCC | － | － | 1.8/2.8 | 3.3 | V |
| Supply Voltage for analog | VCI | － | － | 2.8 | 3.3 | V |
| Power Supply for Current | ICC | IOVCC=VCI =VCC=3.3V |
－ | 13.6 | － | mA |
| NO | Symbol | Function | I/O |
|---|---|---|---|
| 1 | VCI | A supply voltage to the analog circuit. Connect to an external power supply of 2.5 ~ 3.3V. Connect to a stabilizing capacitor between VCI and GND. |
P |
| 2 | IOVCC | A supply voltage to the digital circuit. Connect to an external power supply of 1.65 ~ 3.3V. | P |
| 3 | RESET | Reset input signal Initialize the chip with a low input. Be sure to execute a power-on reset after supplying power. |
I |
| 4 | GND | Ground | I |
| 5 | MIPI_CLK_P | Positive polarity of low voltage differential clock signal Leave the pin open when not in use. | I |
| 6 | MIPI_CLK_N | Negative polarity of low voltage differential clock signal Leave the pin open when not in use |
I |
| 7 | GND | Ground | I |
| 8 | MIPI_DATA_P | Positive polarity of low voltage differential data signal Leave the pin open when not in use. |
I |
| 9 | MIPI_DATA_N | Negative polarity of low voltage differential data signal Leave the pin open when not in use. |
I |
| 10 | GND | Ground | I |
| 11 | VLED+ | Anode of LED backlight. | |
| 12 | VLED- | Cathode of LED backlight |
By clicking "Allow All Cookies", you agree to the storing of cookies on your device to enhance site navigation, analyse site usage, and assist in our marketing and performance efforts. You can find further information this subject in our policy.
