Model No. WF52QTLBSDBN0
►Size : 5.2”
►Resolution : 480 x 128 dots
►View Direction : 6H
►Interface : 8080, MPU
►Controller IC : SSD1963
►Control-Board : Yes
►Brightness (cd/m²): 500
►Frame Through Hole : Yes
►Touch Screen : Without touch screen
The WF52QTLBSDBN0 model is an upgraded solution, replacing the monochrome Graphic STN WG24064A COB module with a colorful TFT display, both having a diagonal size of 5.2 inches. The STN WG24064A has a resolution of 240x64 pixels, while the TFT WF52QTLBSDBN0 offers a higher resolution of 480x128 pixels, providing vibrant, colorful images. WINSTAR has designed the WF52A series with an SSD1963 controller board to serve as a direct replacement for the STN WG24064A.
The WINSTAR TFT WF52QTLBSDBN0 has a module dimension of 180.0 x 65.0 mm, which is the same as the WINSTAR monochrome Graphic WG24064A. Therefore, customers can directly upgrade from the existing mono STN WG24064A to a color TFT display, thanks to the Pin-to-Pin interface design of the WF52QTLBSDBN0. Please refer to the pin assignment below for the WF52QTLBSDBN0.
The WF52QTLBSDBN0 module comes with an integrated SSD1963 controller board. It supports 8080 family MPU 8-bit and 16-bit parallel interfaces. There are two connection interface options: 26-pin 8-bit using a pin header, and 36-pin 8-bit/16-bit using a ZIF connector. The LCM pin definition for CON1 is designed for users of the WG24064A version, with a direct pin-to-pin connection from pin 1 to pin 20. While the WG24064A uses the A.K pin for backlight, the WF52QTLBSDBN0 uses pins 21 and 22 for the backlight.
This TFT LCD WF52QTLBSDBN0 module operates in temperatures ranging from -20℃ to +70℃ and can be stored in temperatures between -30℃ and +80℃.
| Item | Dimension | Unit |
|---|---|---|
| Size | 5.2 | inch |
| Dot Matrix | 480 × RGB × 128 | dots |
| Module dimension | 180.0 × 65.0 × 8.8 | mm |
| Active area | 127.152 × 33.9072 | mm |
| Dot pitch | 0.0883 × 0.2649 | mm |
| LCD type | TFT, Normally White, Transmissive | |
| View Direction | 6 o'clock | |
| Gray Scale Inversion Direction | 12 o'clock | |
| Aspect Ratio | Bar Type | |
| Backlight Type | LED, Normally White | |
| Driver IC | SSD1963 | |
| Interface | Digital 8080 family MPU 8bit/16bit | |
| Touch Panel | Without touch panel | |
| Surface | Glare | |
| Item | Symbol | Min | Typ | Max | Unit |
|---|---|---|---|---|---|
| Operating Temperature | TOP | -20 | － | +70 | ℃ |
| Storage Temperature | TST | -30 | － | +80 | ℃ |
| Item | Symbol | Condition | Min | Typ | Max | Unit |
|---|---|---|---|---|---|---|
| Supply Voltage For LCM | VDD | － | 3.0 | 3.1 | 3.3 | V |
| Supply Current For LCM | IDD | － | － | 200 | － | mA |
| Pin | Symbol | Function |
|---|---|---|
| 1 | GND | System round pin of the IC. Connect to system ground. |
| 2 | VDD | Power Supply : +3.3V |
| 3 | BL_E | Backlight control signal , H: On \ L: Off |
| 4 | D/C | Data/Command select |
| 5 | WR | Write strobe signal |
| 6 | RD | Read strobe signal |
| 7 | DB0 | Data bus |
| 8 | DB1 | Data bus |
| 9 | DB2 | Data bus |
| 10 | DB3 | Data bus |
| 11 | DB4 | Data bus |
| 12 | DB5 | Data bus |
| 13 | DB6 | Data bus |
| 14 | DB7 | Data bus |
| 15 | DB8 | Data bus (When select 8bits mode, this pin is NC) |
| 16 | DB9 | Data bus (When select 8bits mode, this pin is NC) |
| 17 | DB10 | Data bus (When select 8bits mode, this pin is NC) |
| 18 | DB11 | Data bus (When select 8bits mode, this pin is NC) |
| 19 | DB12 | Data bus (When select 8bits mode, this pin is NC) |
| 20 | DB13 | Data bus (When select 8bits mode, this pin is NC) |
| 21 | DB14 | Data bus (When select 8bits mode, this pin is NC) |
| 22 | DB15 | Data bus (When select 8bits mode, this pin is NC) |
| 23 | NC | No connect |
| 24 | NC | No connect |
| 25 | CS | Chip select |
| 26 | RESET | Hardware reset |
| 27 | LR | Right /Left selection; Default R/L is Pull High |
| 28 | UD | Up/down selection; Default U/D is Pull High |
| 29 | NC | No connection |
| 30 | NC | No connection |
| 31 | NC | No connection |
| 32 | NC | No connection |
| 33 | VLED- | VLED- for B/L LED inverter (GND) |
| 34 | VLED- | VLED- for B/L LED inverter (GND) |
| 35 | VLED+ | VLED+ for B/L LED inverter (+5V) |
| 36 | VLED+ | VLED+ for B/L LED inverter (+5V) |
| Pin | Symbol | Function |
|---|---|---|
| 1 | NC(FG) | No connect (Frame Grand) |
| 2 | GND | System round pin of the IC. Connect to system ground. |
| 3 | VDD | Power Supply : +3.3V |
| 4 | BLE | Backlight control signal , H: On \ L: Off |
| 5 | WR | Write strobe signal |
| 6 | RD | Read strobe signal |
| 7 | CS | Chip select |
| 8 | D/C | Data/Command select |
| 9 | NC | No connect |
| 10 | RESET | Hardware reset |
| 11 | DB0 | Data bus |
| 12 | DB1 | Data bus |
| 13 | DB2 | Data bus |
| 14 | DB3 | Data bus |
| 15 | DB4 | Data bus |
| 16 | DB5 | Data bus |
| 17 | DB6 | Data bus |
| 18 | DB7 | Data bus |
| 19 | NC | No connect |
| 20 | NC | No connect |
| 21 | VLED+ | VLED+ for B/L LED inverter (+5V) |
| 22 | VLED- | VLED- for B/L LED inverter (GND) |
| 23 | NC | No connect |
| 24 | NC | No connect |
| 25 | NC | No connect |
| 26 | GND | System round pin of the IC. Connect to system ground. |
By clicking "Allow All Cookies", you agree to the storing of cookies on your device to enhance site navigation, analyse site usage, and assist in our marketing and performance efforts. You can find further information this subject in our policy.