หน้าแรก ผลิตภัณฑ์ โมดูล OLED จอ OLED กราฟฟิก WEF012864H

128x64, 2.42" COG+FR COG OLED กราฟฟิก

หมายเลขรุ่น WEF012864H

►ประเภท: กราฟฟิก (พร้อมกรอบ)
►โครงสร้าง: COG+FR
►ขนาด: 2.42 นิ้ว
►128x64 Dot Matrix
►IC:SSD1309
►แหล่งจ่ายไฟ 3V
►1/64 duty
►อินเตอร์เฟซ: 6800, 8080, SPI, I2C
►สีการแสดงผล: ขาว / สีเหลือง / สีฟ้าคราม / สีเขียว

การร่าง

WEF012864H
Data source ref:WEF012864HWPP3N00F00

ข้อมูลจำเพาะ

คุณสมบัติการปักไว้ที่อินเตอร์เฟส

Pin No. สัญลักษณ์ คุณสมบัติการทำงาน
1 NC(Vss) No connection (ground.)
2 VCC Power supply for panel driving voltage. This is also the most positive power voltage supply pin.
3 VCOMH COM signal deselected voltage level.
A capacitor should be connected between this pin and VSS.
4 IREF This pin is the segment output current reference pin.
IREF is supplied externally.
A resistor should be connected between this pin and VSS to maintain the current around 10uA. Please refer to Figure 8-15 for the details of resistor value
5~12 D7~D0 These pins are bi-directional data bus connecting to the MCU data bus.
Unused pins are recommended to tie LOW.
When serial interface mode is selected, D0 will be the serial clock input: SCLK; D1 will be the serial data input: SDIN and D2 should be kept NC.
When I2C mode is selected, D2, D1 should be tied together and serve as SDAout, SDAin in application and D0 is the serial clock input, SCL.
13 E/RD# This pin is MCU interface input.
When 6800 interface mode is selected, this pin will be used as the Enable (E) signal.
Read/write operation is initiated when this pin is pulled HIGH and the chip is selected.
When 8080 interface mode is selected, this pin receives the Read (RD#) signal. Read operation is initiated when this pin is pulled LOW and the chip is selected.
When serial or I2C interface is selected, this pin must be connected to VSS.
14 R/W# This pin is read / write control input pin connecting to the MCU interface.
When 6800 interface mode is selected, this pin will be used as Read/Write (R/W#)
selection input. Read mode will be carried out when this pin is pulled HIGH and
write mode when LOW.
When 8080 interface mode is selected, this pin will be the Write (WR#) input. Data
write operation is initiated when this pin is pulled LOW and the chip is selected.
When serial or I2C interface is selected, this pin must be connected to VSS.
15 D/C# This pin is Data/Command control pin connecting to the MCU.
When the pin is pulled HIGH, the data at D[7:0] will be interpreted as data.
When the pin is pulled LOW, the data at D[7:0] will be transferred to a command
register.
In I2C mode, this pin acts as SA0 for slave address selection.
When 3-wire serial interface is selected, this pin must be connected to VSS.
For detail relationship to MCU interface signals, refer to Timing Characteristics
16 RES# This pin is reset signal input.
When the pin is pulled LOW, initialization of the chip is executed.
Keep this pin pull HIGH during normal operation.
17 CS# This pin is the chip select input connecting to the MCU.
The chip is enabled for MCU communication only when CS# is pulled LOW (active
LOW).
18 NC No connection
19 BS2 MCU bus interface selection pins. Select appropriate logic setting as described in the
following table.

Note
(1) 0 is connected to VSS
(2) 1 is connected to VDD
20 BS1
21 Vdd Power supply pin for core logic operation
22~28 NC No connection
29 Vss Ground pin. It must be connected to external ground.
30 NC(Vss) No connection (ground.)

ข้อกำหนดทั่วไป

รายการ ขนาด หน่วย
ความละเอียด 128 × 64 จุด
ขนาดโมดูล 77.2 × 42.14 ×3.4 mm
พื้นที่ที่ใช้งานอยู่ 55.01 × 27.49 mm
ขนาดจุด 0.40 × 0.40 mm
ระดับจุด 0.43 × 0.43 mm
โหมดการแสดงผล Passive Matrix
สีการแสดงผล ขาวดำ
Drive Duty 1/64 Duty
IC SSD1309
อินเตอร์เฟซ 6800,8080,SPI,I2C
ขนาด (เส้นทแยงมุม) 2.42 นิ้ว

คะแนนสูงสุด

Parameter สัญลักษณ์ ค่าต่ำสุด ค่าสูงสุด หน่วย
Supply Voltage for Logic VDD -0.3 4 V
Supply Voltage for Display VCC 0 15 V
อุณหภูมิในการทำงาน TOP -40 +80 °C
อุณหภูมิในการจัดเก็บ TSTG -40 +85 °C

ลักษณะทางอิเล็กทรอนิก

DC ลักษณะทางอิเล็กทรอนิก

รายการ สัญลักษณ์ เงื่อนไข ค่าต่ำสุด ค่าปกติ ค่าสูงสุด หน่วย
Supply Voltage for Logic VDD 2.8 3.0 3.3 V
Supply Voltage for Display VCC 12.5 13.0 13.5 V
High Level Input VIH 0.8×VDD VDD V
Low Level Input VIL 0 0.2×VDD V
High Level Output VOH 0.9×VDD VDD V
Low Level Output VOL 0 0.1×VDD V
50% Check Board operating Current VCC =13V - 29 43.5 mA

Search keyword: 128x64 oled, oled 128x64, 2.42 oled, 2.42 นิ้ว oled, oled 2.42
go top
close