2.7", 128x64 Графические OLED дисплей модули
Артикул. WEO012864Q
►Тип: Графический
►Тип монтажа контроллера: COG; Frame Option
►Диагональ: 2.7 дюйма
►Разрешение: 128 x 64 точек
►IC:SSD1309
►3V Power supply
►1/64 duty
►Интерфейс: 6800, 8080, SPI, I2C
►Цвет дисплея: Белый / Желтый / Небесно голубой / Зеленый
Описание
WinSTAR OLED – дисплей WEO012864Q представляет собой модуль дисплея с пассивной матрицей OLED-2.7” (128x64 точек). Этот графический дисплей имеет встроенный IC SSD1309,с поддержкой 6800/8080 8-бит, I2C и 4-wire интерфейсов. Источник питания 3V. WEO012864Q обладает размером модуля 73.0 x 41.86 mm, с активной площадью 61.41 x 30.69 mm; Индикатор WEO012864Q – представляет собой индикатор WEF012864Q, но без рамки с распиновкой, идентичной TAB OLED WEX012864L, которая была снята с производства. (30 pins).
Преимуществом этих 2.7” COG OLED индикаторов WEO012864Q – является легкий вес и низкое энергопотребление, что идеально подходит для измерительных устройств, домашних приложений, POS-систем, Cloud / IoT-систем, интеллектуальных технологических устройств, энергетических систем, систем связи, медицинских инструментов и т. Д. Модуль WEO012864Q OLED может работать при температурах от -40 ℃ до + 85 ℃, а температура хранения от -40 ℃ до + 80 ℃.
Frame OptionЧертеж
Data source ref: WEO012864QWPP3N00000
Технические характеристики
Функции контроллера контактного интерфейса
No. | Символы | Описание | |||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
1 | NC | No connection | |||||||||||||||
2 | VCC | Power supply for panel driving voltage. This is also the most positive power voltage supply pin. | |||||||||||||||
3 | VCOMH | COM signal deselected voltage level. A capacitor should be connected between this pin and VSS. |
|||||||||||||||
4 | IREF | This pin is the segment output current reference pin. IREF is supplied externally. | |||||||||||||||
5~12 | D7~D0 | These pins are bi-directional data bus connecting to the MCU data bus. Unused pins are recommended to tie LOW. When serial interface mode is selected, D0 will be the serial clock input: SCLK; D1 will be the serial data input: SDIN and D2 should be kept NC. When I2C mode is selected, D2, D1 should be tied together and serve as SDAout, SDAin in application and D0 is the serial clock input, SCL. |
|||||||||||||||
13 | E/RD# | This pin is MCU interface input. When 6800 interface mode is selected, this pin will be used as the Enable (E) signal. Read/write operation is initiated when this pin is pulled HIGH and the chip is selected. When 8080 interface mode is selected, this pin receives the Read (RD#) signal. Read operation is initiated when this pin is pulled LOW and the chip is selected. When serial or I2C interface is selected, this pin must be connected to VSS. |
|||||||||||||||
14 | R/W# | This pin is read / write control input pin connecting to the MCU interface. When 6800 interface mode is selected, this pin will be used as Read/Write (R/W#) selection input. Read mode will be carried out when this pin is pulled HIGH and write mode when LOW. When 8080 interface mode is selected, this pin will be the Write (WR#) input. Data write operation is initiated when this pin is pulled LOW and the chip is selected. When serial or I2C interface is selected, this pin must be connected to VSS. |
|||||||||||||||
15 | D/C# | This pin is Data/Command control pin connecting to the MCU. When the pin is pulled HIGH, the data at D[7:0] will be interpreted as data. When the pin is pulled LOW, the data at D[7:0] will be transferred to a command register. In I2C mode, this pin acts as SA0 for slave address selection. When 3-wire serial interface is selected, this pin must be connected to VSS. |
|||||||||||||||
16 | RES# | This pin is reset signal input. When the pin is pulled LOW, initialization of the chip is executed. Keep this pin pull HIGH during normal operation. |
|||||||||||||||
17 | CS# | This pin is the chip select input connecting to the MCU. The chip is enabled for MCU communication only when CS# is pulled LOW (active LOW). |
|||||||||||||||
18 | NC | No connection | |||||||||||||||
19 | BS2 | MCU bus interface selection pins. Select appropriate logic setting as described in the following table. BS2, BS1 and BS0 are pin select
Note (1) 0 is connected to VSS (2) 1 is connected to VDD |
|||||||||||||||
20 | BS1 | ||||||||||||||||
21 | VDD | Power supply pin for core logic operation | |||||||||||||||
22~28 | NC | No connection | |||||||||||||||
29 | VSS | Ground. | |||||||||||||||
30 | NC | No connection |
Механические характеристики
Наименование | Измерения | Единица |
---|---|---|
Разрешение | 128 x 64 | точек |
Габариты | 73.0 × 41.86 × 2.05 | mm |
Активная область | 61.41 × 30.69 | mm |
Размер пикселя | 0.45 × 0.45 | mm |
Шаг пикселя | 0.48 × 0.48 | mm |
Матрица | Пассивная матрица | |
Цвет дисплея | монохромные | |
Рабочий цикл | 1/64 Duty | |
IC | SSD1309 | |
Интерфейс | I2C, 4-Wire SPI ,6800, 8080 | |
Диагональ | 2.7 дюйма |
Абсолютные максимальные значения
Parameter | Символы | Минимальный | Максимальный | Единица |
---|---|---|---|---|
Напряжение питания логических схем | VDD | -0.3 | 4 | V |
Напряжение питания дисплея | VCC | 0 | 15 | V |
Диапазон рабочих температур | TOP | -40 | +80 | °C |
Температура хранения | TSTG | -40 | +85 | °C |
Электронные характеристики
Наименование | Символы | Кондиция | Минимальный | Типичный | Максимальный | Единица |
---|---|---|---|---|---|---|
Напряжение питания логических схем | VDD | - | 2.8 | 3.0 | 3.3 | V |
Напряжение питания дисплея | VCC | - | 12.5 | 13 | 13.5 | V |
Вход высокого уровня | VIH | - | 0.8×VDD | - | - | V |
Вход низкого уровня | VIL | - | - | - | 0.2×VDD | V |
Выход высокого уровня | VOH | - | 0.9×VDD | - | - | V |
Выход низкого уровня | VOL | - | - | - | 0.1×VDD | V |
50% Check Board operating Current | VCC =13.0V | 20 | 22 | 24 | mA |
Frame Option:
Drawing | Material | FR No. | Detailed Drawing | Create Date |
---|---|---|---|---|
SUS-304 | FFL60128640A221XXX00 | View | 20120131 |
Search keyword: 128x64 oled, oled 128x64, 2.7 oled, 2.7 дюйма oled, oled 2.7