ホーム 製品 OLEDディスプレイ モジュール グラフィック有機ELモジュール WEO012864Q

2.7インチ128x64グラフィック有機ELディスプレイ

型番 WEO012864Q

►タイプ: グラフィック有機ELディスプレイ
►結構: COG; Frame Option
►サイズ: 2.7インチ
►128 x 64 ドットマトリックス
►IC:SSD1309
►3V電源電圧
►1/64 duty
►インターフェース: 6800, 8080, SPI, I2C
►発光色: 白色 / 黄色 / 空色 / 緑色

製品情報

WinstarのWEO012864Qは2.7インチ、128x64ドットのOLEDディスプレイモジュールです。このグラフィックディスプレーはSSD1309コントローラーICが内蔵し、インターフェースが6800/8080 8-bit、I2C及び 4線式シリアルが使用でき、3V電源のモジュールです。WEO012864Qのモジュール寸法は73.0 x 41.86 mmで、アクティブエリアサイズは61.41x30.69mmです。このアイテムはOLEDパネルWEO012864Kと同じく30ぴんFPCがあり、FPCのピン割り当てはWEX012864L(30ピン)と同じに定義されています。

WEO012864QはCOG構造のOLEDディスプレイです。このアイテムは軽量で、低消費電力で、超薄型です。このOLEDモジュールは壁/メーター機器、家庭用アプリケーション、POSシステム、クラウド/IoTシステム、インテリジェンステクノロジデバイス、エネルギーシステム、通信システム、医療器械などに適しています。WEO012864Q OLEDモジュールの動作可能の温度範囲は-40℃〜+80℃、保存温度範囲は-40℃〜+85℃です。このアイテムの標準発光色は黄色、白色とスカイブルーで利用できます。

     Frame Option

外形図

Winstar Display - 2.7", 128x64, Monochrome Graphic OLED Display

Data source ref: WEO012864QWPP3N00000

製品仕様

規格説明

項目 仕様 単位
ドットマトリックス(解像度) 128 x 64
モジュールサイズ 73.0 × 41.86 × 2.05 mm
有効エリア 61.41 × 30.69 mm
ドットサイズ 0.45 × 0.45 mm
ドットピッチ 0.48 × 0.48 mm
表示モード 被动矩阵
発光色 单色
駆動方法 1/64 Duty
IC SSD1309
インターフェイス I2C, 4-Wire SPI ,6800, 8080
表示サイズ(対角線) 2.7 インチ

絶対最大定格

パラメーター 記号 最小値 最大値 単位
ロジック電源電圧 VDD -0.3 4 V
Display電源電圧 VCC 0 15 V
操作温度 TOP -40 +80 °C
保存温度 TSTG -40 +85 °C

電気特性

項目 記号 条件 最小値 典型値 最大値 単位
ロジック電源電圧 VDD 2.8 3.0 3.3 V
Display電源電圧 VCC 12.5 13 13.5 V
高レベル入力 VIH 0.8×VDD V
低レベル入力 VIL 0.2×VDD V
高レベル出力 VOH 0.9×VDD V
低レベル出力 VOL 0.1×VDD V
50% Check Board operating Current VCC =13.0V 20 22 24 mA

ピン功能定義

No. 記号 説明
1 NC  No connection
2 VCC Power supply for panel driving voltage. This is also the most positive power voltage supply pin.
3 VCOMH COM signal deselected voltage level.
A capacitor should be connected between this pin and VSS.
4 IREF This pin is the segment output current reference pin. IREF is supplied externally.
5~12 D7~D0 These pins are bi-directional data bus connecting to the MCU data bus.
Unused pins are recommended to tie LOW.
When serial interface mode is selected, D0 will be the serial clock input: SCLK; D1 will be the serial data input: SDIN and D2 should be kept NC.
When I2C mode is selected, D2, D1 should be tied together and serve as SDAout, SDAin in application and D0 is the serial clock input, SCL.
13 E/RD# This pin is MCU interface input.
When 6800 interface mode is selected, this pin will be used as the Enable (E) signal.
Read/write operation is initiated when this pin is pulled HIGH and the chip is selected.
When 8080 interface mode is selected, this pin receives the Read (RD#) signal. Read operation is initiated when this pin is pulled LOW and the chip is selected.
When serial or I2C interface is selected, this pin must be connected to VSS.
14 R/W# This pin is read / write control input pin connecting to the MCU interface.
When 6800 interface mode is selected, this pin will be used as Read/Write (R/W#) selection input. Read mode will be carried out when this pin is pulled HIGH and write mode when LOW.
When 8080 interface mode is selected, this pin will be the Write (WR#) input. Data write operation is initiated when this pin is pulled LOW and the chip is selected.
When serial or I2C interface is selected, this pin must be connected to VSS.
15 D/C# This pin is Data/Command control pin connecting to the MCU.
When the pin is pulled HIGH, the data at D[7:0] will be interpreted as data.
When the pin is pulled LOW, the data at D[7:0] will be transferred to a command register.
In I2C mode, this pin acts as SA0 for slave address selection.
When 3-wire serial interface is selected, this pin must be connected to VSS.
16 RES# This pin is reset signal input.
When the pin is pulled LOW, initialization of the chip is executed.
Keep this pin pull HIGH during normal operation.
17 CS# This pin is the chip select input connecting to the MCU.
The chip is enabled for MCU communication only when CS# is pulled LOW (active LOW).
18 NC No connection
19 BS2 MCU bus interface selection pins. Select appropriate logic setting as described in the following table. BS2, BS1 and BS0 are pin select
  BS1 BS2
I2C 1 0
4-wire Serial 0 0
8-bit 68XX parallel 0 1
8-bit 80XX parallel 1 1

Note
(1) 0 is connected to VSS
(2) 1 is connected to VDD
20 BS1
21 VDD Power supply pin for core logic operation
22~28 NC No connection
29 VSS Ground.
30 NC No connection

Frame Option:

Drawing Material FR No. Detailed Drawing Create Date
WEF012864Q SUS-304 FFL60128640A221XXX00 View 20120131
go top
close

私たちはあなたのプライバシーを大切にします

「すべてのクッキーを許可」をクリックすると、サイトのナビゲーションを向上させ、サイト使用状況を分析し、マーケティングおよびパフォーマンスの取り組みを支援するために、クッキーをデバイスに保存することに同意したことになります。この件に関する詳細情報は、ポリシーをご覧ください。プライバシーポリシー

私たちはあなたのプライバシーを大切にします

Winstarおよび特定の第三者は、www.winstar.com.twでクッキーを使用しています。クッキーの種類、目的、および関与する第三者に関する詳細は、以下および当社のクッキーポリシーに記載されています。「すべて許可」をクリックして、当社のクッキー使用に同意し、ウェブサイトでの最良の体験を得てください。また、設定を変更するか、必要なクッキーを除きクッキーを拒否することもできます。

同意設定の管理

常にアクティブ
必須なクッキー

これらのクッキーは、ウェブサイト内を移動したり、プライバシーの設定、ログイン、フォームの記入などの機能を使用できるようにするために不可欠です。

分析用クッキー

「統計クッキー」とも呼ばれるこれらのクッキーは、ウェブサイトの使用方法に関する情報を収集します。たとえば、どのページを訪れ、どのリンクをクリックしたかなどです。詳細を確認してください。