產品敘述
WEO012864Q 是一款2.7吋無鐵框的COG 繪圖型單色被動式OLED顯示器模組，面板解析度128x64 pixels。WEO012864Q內建SSD1309 controller控制器, 支援多種傳輸介面: 6800 8-bite, 8080 8-bit 平行介面, I2C 與4線SPI串列介面，使用3V驅動。 WEO012864Q的模組尺寸為73.0 x 41.86 mm， AA區尺寸為61.41 x 30.69 mm，此款型號與現有的WEO012864K使用相同的OLED面板，但FPC出pin與定義同WEX012864L(30 pins)。
WEO012864Q為COG結構的OLED顯示器模組，為有機自發光，無須背光源，模組輕薄且低耗電流，WEF012864Q模組非常適合手持式產品、量測儀器、家用產品、POS系統、物聯網、通訊設備與醫療儀器等等。此模組的工作溫度是-40℃至+80℃，儲存溫度-40℃至+85℃。
可另選加鐵框 規格圖
Data source ref: WEO012864QWPP3N00000
產品規格
Pin功能定義
| No. | 符號 | 功能說明 | |||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 1 | NC | No connection | |||||||||||||||
| 2 | VCC | Power supply for panel driving voltage. This is also the most positive power voltage supply pin. | |||||||||||||||
| 3 | VCOMH | COM signal deselected voltage level. A capacitor should be connected between this pin and VSS. |
|||||||||||||||
| 4 | IREF | This pin is the segment output current reference pin. IREF is supplied externally. | |||||||||||||||
| 5~12 | D7~D0 | These pins are bi-directional data bus connecting to the MCU data bus. Unused pins are recommended to tie LOW. When serial interface mode is selected, D0 will be the serial clock input: SCLK; D1 will be the serial data input: SDIN and D2 should be kept NC. When I2C mode is selected, D2, D1 should be tied together and serve as SDAout, SDAin in application and D0 is the serial clock input, SCL. |
|||||||||||||||
| 13 | E/RD# | This pin is MCU interface input. When 6800 interface mode is selected, this pin will be used as the Enable (E) signal. Read/write operation is initiated when this pin is pulled HIGH and the chip is selected. When 8080 interface mode is selected, this pin receives the Read (RD#) signal. Read operation is initiated when this pin is pulled LOW and the chip is selected. When serial or I2C interface is selected, this pin must be connected to VSS. |
|||||||||||||||
| 14 | R/W# | This pin is read / write control input pin connecting to the MCU interface. When 6800 interface mode is selected, this pin will be used as Read/Write (R/W#) selection input. Read mode will be carried out when this pin is pulled HIGH and write mode when LOW. When 8080 interface mode is selected, this pin will be the Write (WR#) input. Data write operation is initiated when this pin is pulled LOW and the chip is selected. When serial or I2C interface is selected, this pin must be connected to VSS. |
|||||||||||||||
| 15 | D/C# | This pin is Data/Command control pin connecting to the MCU. When the pin is pulled HIGH, the data at D[7:0] will be interpreted as data. When the pin is pulled LOW, the data at D[7:0] will be transferred to a command register. In I2C mode, this pin acts as SA0 for slave address selection. When 3-wire serial interface is selected, this pin must be connected to VSS. |
|||||||||||||||
| 16 | RES# | This pin is reset signal input. When the pin is pulled LOW, initialization of the chip is executed. Keep this pin pull HIGH during normal operation. |
|||||||||||||||
| 17 | CS# | This pin is the chip select input connecting to the MCU. The chip is enabled for MCU communication only when CS# is pulled LOW (active LOW). |
|||||||||||||||
| 18 | NC | No connection | |||||||||||||||
| 19 | BS2 | MCU bus interface selection pins. Select appropriate logic setting as described in the following table. BS2, BS1 and BS0 are pin select
Note (1) 0 is connected to VSS (2) 1 is connected to VDD |
|||||||||||||||
| 20 | BS1 | ||||||||||||||||
| 21 | VDD | Power supply pin for core logic operation | |||||||||||||||
| 22~28 | NC | No connection | |||||||||||||||
| 29 | VSS | Ground. | |||||||||||||||
| 30 | NC | No connection |
規格說明
| 項目 | 尺寸 | 單位 |
|---|---|---|
| 點陣(解析度) | 128 x 64 | － |
| 模組尺寸 | 73.0 × 41.86 × 2.05 | mm |
| 有效區域 | 61.41 × 30.69 | mm |
| 點大小 | 0.45 × 0.45 | mm |
| 點間距 | 0.48 × 0.48 | mm |
| 顯示模式 | 被動矩陣 | |
| 顯示顏色 | 單色 | |
| 驅動方式 | 1/64 Duty | |
| IC | SSD1309 | |
| 介面 | I2C, 4-Wire SPI ,6800, 8080 | |
| 尺寸 | 2.7 吋 | |
最大绝对额定值
| 參數 | 符號 | 最大值 | 最大值 | 單位 |
|---|---|---|---|---|
| 邏輯電源電壓 | VDD | -0.3 | 4 | V |
| 顯示電源電壓 | VCC | 0 | 15 | V |
| 工作溫度 | TOP | -40 | +80 | °C |
| 儲存溫度 | TSTG | -40 | +85 | °C |
電氣特性
| 項目 | 符號 | 條件 | 最大值 | 典型值 | 最大值 | 單位 |
|---|---|---|---|---|---|---|
| 邏輯電源電壓 | VDD | － | 2.8 | 3.0 | 3.3 | V |
| 顯示電源電壓 | VCC | － | 12.5 | 13 | 13.5 | V |
| 輸入高準位 | VIH | － | 0.8×VDD | － | － | V |
| 輸入低準位 | VIL | － | － | － | 0.2×VDD | V |
| 輸出高準位 | VOH | － | 0.9×VDD | － | － | V |
| 輸出低準位 | VOL | － | － | － | 0.1×VDD | V |
| 50%顯示畫面耗電流 | VCC =13.0V | 20 | 22 | 24 | mA | |
可選加鐵框:
| 圖示 | 材質 | 鐵框料號 | 詳細規格圖 | 建立日期 |
|---|---|---|---|---|
 |
SUS-304 | FFL60128640A221XXX00 | 檢視 | 20120131 |
Search keyword: 128x64 oled, oled 128x64, 2.7 oled, 2.7 吋oled, oled 2.7
