Strona główna Produkty Wyświetlacz OLED Graficzne Wyświetlacz OLED WEO012864Q

2.7", 128x64 Wyświetlaczy graficznych OLED

Numer modelu WEO012864Q

►Typ: graficzny
►Struktura: COG; Frame Option
►Rozmiar: 2.7"
►128 x 64 matryca punktowa
►IC:SSD1309
►zasilanie 3V
►wypełnienie 1/64
►Interfejs: 6800, 8080, SPI, I2C
►Kolor wyświetlacza: biały / żółto / jasnoniebieski / zielony

Opis

     Opcja ramki

Rysunek

Winstar Display - 2.7", 128x64, Monochrome Graphic OLED Display

Data source ref: WEO012864QWPP3N00000

Specyfikacja

Dane mechaniczne

Rzecz Wymiar Jednostka
Matryca punktowa 128 × 64
Wymiary modułu 73.0 × 41.86 × 2.05 mm
Obszar aktywny 61.41 × 30.69 mm
Wielkość piksela 0.45 × 0.45 mm
Raster pomiędzy pikselami 0.48 × 0.48 mm
Tryb wyświetlania matryca
Kolor wyświetlacza Monochromatyczny
Drive Duty 1/64 Duty
IC SSD1309
Interfejs I2C, 4-Wire SPI ,6800, 8080
Rozmiar (Przekątna) 2.7 cale

Bezwzględne oceny maksymalne

Parameter Symbol Minimalna wartość Maksymalna wartość Jednostka
Supply Voltage for Logic VDD -0.3 4 V
Supply Voltage for Display VCC 0 15 V
Temperatura pracy TOP -40 +80 °C
Temperatura przechowywania TSTG -40 +85 °C

Parametry elektryczne

Rzecz Symbol Stan Minimalna wartość Typowa wartość Maksymalna wartość Jednostka
Supply Voltage for Logic VDD 2.8 3.0 3.3 V
Supply Voltage for Display VCC 12.5 13 13.5 V
High Level Input VIH 0.8×VDD V
Low Level Input VIL 0.2×VDD V
High Level Output VOH 0.9×VDD V
Low Level Output VOL 0.1×VDD V
50% Check Board operating Current VCC =13.0V 20 22 24 mA

Funkcja pinów interfejsu

No. Symbol Funkcja
1 NC  No connection
2 VCC Power supply for panel driving voltage. This is also the most positive power voltage supply pin.
3 VCOMH COM signal deselected voltage level.
A capacitor should be connected between this pin and VSS.
4 IREF This pin is the segment output current reference pin. IREF is supplied externally.
5~12 D7~D0 These pins are bi-directional data bus connecting to the MCU data bus.
Unused pins are recommended to tie LOW.
When serial interface mode is selected, D0 will be the serial clock input: SCLK; D1 will be the serial data input: SDIN and D2 should be kept NC.
When I2C mode is selected, D2, D1 should be tied together and serve as SDAout, SDAin in application and D0 is the serial clock input, SCL.
13 E/RD# This pin is MCU interface input.
When 6800 interface mode is selected, this pin will be used as the Enable (E) signal.
Read/write operation is initiated when this pin is pulled HIGH and the chip is selected.
When 8080 interface mode is selected, this pin receives the Read (RD#) signal. Read operation is initiated when this pin is pulled LOW and the chip is selected.
When serial or I2C interface is selected, this pin must be connected to VSS.
14 R/W# This pin is read / write control input pin connecting to the MCU interface.
When 6800 interface mode is selected, this pin will be used as Read/Write (R/W#) selection input. Read mode will be carried out when this pin is pulled HIGH and write mode when LOW.
When 8080 interface mode is selected, this pin will be the Write (WR#) input. Data write operation is initiated when this pin is pulled LOW and the chip is selected.
When serial or I2C interface is selected, this pin must be connected to VSS.
15 D/C# This pin is Data/Command control pin connecting to the MCU.
When the pin is pulled HIGH, the data at D[7:0] will be interpreted as data.
When the pin is pulled LOW, the data at D[7:0] will be transferred to a command register.
In I2C mode, this pin acts as SA0 for slave address selection.
When 3-wire serial interface is selected, this pin must be connected to VSS.
16 RES# This pin is reset signal input.
When the pin is pulled LOW, initialization of the chip is executed.
Keep this pin pull HIGH during normal operation.
17 CS# This pin is the chip select input connecting to the MCU.
The chip is enabled for MCU communication only when CS# is pulled LOW (active LOW).
18 NC No connection
19 BS2 MCU bus interface selection pins. Select appropriate logic setting as described in the following table. BS2, BS1 and BS0 are pin select
  BS1 BS2
I2C 1 0
4-wire Serial 0 0
8-bit 68XX parallel 0 1
8-bit 80XX parallel 1 1

Note
(1) 0 is connected to VSS
(2) 1 is connected to VDD
20 BS1
21 VDD Power supply pin for core logic operation
22~28 NC No connection
29 VSS Ground.
30 NC No connection

Opcja ramki:

Obraz Material FR No. Detailed Drawing Create Date
WEF012864Q SUS-304 FFL60128640A221XXX00 View 20120131
go top
close

Cenimy twoją prywatność

Klikając „Zezwól na wszystkie pliki cookie”, zgadzasz się na przechowywanie plików cookie na swoim urządzeniu w celu usprawnienia nawigacji po witrynie, analizy korzystania z witryny oraz wspierania naszych działań marketingowych i dotyczących wydajności. Więcej informacji na ten temat znajdziesz w naszej polityce. Polityka prywatności

Cenimy twoją prywatność

Winstar i niektóre strony trzecie używają plików cookie na stronie www.winstar.com.tw. Szczegóły dotyczące rodzajów plików cookie, ich celu oraz zaangażowanych stron trzecich są opisane poniżej i w naszej Polityce plików cookie. Kliknij „Zezwól na wszystko”, aby wyrazić zgodę na korzystanie z plików cookie i uzyskać najlepsze możliwe wrażenia na naszych stronach internetowych. Możesz także ustawić preferencje lub odrzucić pliki cookie (z wyjątkiem niezbędnych plików cookie).

Zarządzaj preferencjami zgody

Zawsze aktywne
Niezbędne pliki cookie

Te ciasteczka są niezbędne, aby umożliwić Ci poruszanie się po stronie internetowej i korzystanie z jej funkcji, takich jak ustawianie preferencji prywatności, logowanie się lub wypełnianie formularzy.

Ciasteczka analityczne

Te pliki cookie, znane również jako „ciasteczka statystyczne”, zbierają informacje o tym, jak korzystasz z witryny, takie jak które strony odwiedziłeś i które linki kliknąłeś. Zobacz szczegóły.