На главную страницу Продукция OLED Дисплей Графический OLED дисплей WEO012864A

Олед дисплей (Графические) 1.54", 6800 / 8080 / SPI / I2C интерфейсы, 128x64

Артикул. WEO012864A

►Тип: Графический(Без рамки)
►Тип монтажа контроллера: COG
►Диагональ: 1.54 дюйма
►Разрешение: 128 x 64 точек
►IC:SSD1309
►3V Power supply
►1/64 duty
►Интерфейс: 6800,8080,SPI,I2C
►Цвет дисплея: Белый / Желтый / Зеленый
►Other FPC options available in below table

Описание

Winstar OLED WEO012864A представляет собой модуль дисплея с пассивной матрицей OLED-1,54 дюйма (128x64 точек). WEO012864A обладает размером модуля 42.04 x 27.22 мм, с активной площадью 35.05 x 17.51 мм. WEO012864A имеет встроенный IC SSD1309, с поддержкой 6800/8080 8-бит, I2C и 4-wire интерфейсов. OLED-дисплей WEO012864A имеет COG структуру и является качественным ультратонким дисплеем с отсутствием необходимости в подсветки (сам излучает); Так же преимуществами этих дисплеев является легкий вес и низкое энергопотребление. Этот 1,54-дюймовый OLED  модуль подходит для: измерительных приборов, POS систем, Облачных/IoT систем, умных устройств, энергетических систем, автомобилестроении, коммуникационных систем, медицинских устройств и т.д.

В настоящее время WEO012864A доступен в белом, желтом и оранжевом цветах. Модуль WEO012864A может работать при температурах от -40 ° С до + 80С; а температура хранения - от -40С до + 85С. 


   FPC Options

 

Чертеж

1.54 OLED, SPI OLED, SPI OLED Display, OLED 128x64 SPI, 128x64 OLED SPI - WEO012864A

Data source ref:WEO012864ALAP3N00000

Технические характеристики

Функции контроллера контактного интерфейса

No. Символы Описание
1 NC(GND) No connection
2 VLSS This is an analog ground pin
3 VSS Ground.
4 NC No connection
5 VDD Power supply pin for core logic operation
6 BS1 MCU bus interface selection pins. Select appropriate logic setting as described in the following table. BS2 and BS1 are pin select
  BS1 BS2
I2C 1 0
4-wire Serial 0 0
8-bit 68XX Parallel 0 1
8-bit 80XX Parallel 1 1

Note
(1) 0 is connected to VSS
(2) 1 is connected to VDD
7 BS2
8 CS# This pin is the chip select input connecting to the MCU.
The chip is enabled for MCU communication only when CS# is pulled LOW (active LOW).
9 RES# This pin is reset signal input.
When the pin is pulled LOW, initialization of the chip is executed.
Keep this pin pull HIGH during normal operation.
10 D/C# This pin is Data/Command control pin connecting to the MCU.
When the pin is pulled HIGH, the data at D[7:0] will be interpreted as data.
When the pin is pulled LOW, the data at D[7:0] will be transferred to a command register.
In I2C mode, this pin acts as SA0 for slave address selection.
11 R/W# This pin is read / write control input pin connecting to the MCU interface.
When 6800 interface mode is selected, this pin will be used as Read/Write (R/W#) selection input. Read mode will be carried out when this pin is pulled HIGH and write mode when LOW.
When 8080 interface mode is selected, this pin will be the Write (WR#) input. Data write operation is initiated when this pin is pulled LOW and the chip is selected.
When serial or I2C interface is selected, this pin must be connected to VSS.
12 E/RD# This pin is MCU interface input.
When 6800 interface mode is selected, this pin will be used as the Enable (E) signal.
Read/write operation is initiated when this pin is pulled HIGH and the chip is selected.
When 8080 interface mode is selected, this pin receives the Read (RD#) signal. Read operation is initiated when this pin is pulled LOW and the chip is selected.
When serial or I2C interface is selected, this pin must be connected to VSS.
13-20 D0~D7 These pins are bi-directional data bus connecting to the MCU data bus.
Unused pins are recommended to tie LOW.
When serial interface mode is selected, D0 will be the serial clock input: SCLK; D1 will be the serial data input: SDIN and D2 should be kept NC.
When I2C mode is selected, D2, D1 should be tied together and serve as SDAout, SDAin in application and D0 is the serial clock input, SCL.
21 IREF This pin is the segment output current reference pin.
IREF is supplied externally.
22 VCOMH COM signal deselected voltage level.
A capacitor should be connected between this pin and VSS.
23 VCC Power supply for panel driving voltage. This is also the most positive power voltage supply pin.
24 NC(GND) No connection

Механические характеристики

Наименование Измерения Единица
Разрешение 128 x 64 точек
Габариты 42.04 × 27.22 × 1.41 mm
Активная область 35.05 × 17.51 mm
Размер пикселя 0.249 × 0.249 mm
Шаг пикселя 0.274 × 0.274 mm
Матрица Пассивная матрица
Цвет дисплея монохромные
Рабочий цикл 1/64 Duty
IC SSD1309
Интерфейс 6800/8080/4-Wire SPI/I2C
Диагональ 1.54 дюйма

Абсолютные максимальные значения

Параметр Символы Минимальный Максимальный Единица
Напряжение питания логических схем VDD -0.3 4 V
Напряжение питания дисплея VCC 0 17 V
Диапазон рабочих температур TOP -40 +80 °C
Температура хранения TSTG -40 +85 °C

Электронные характеристики

Наименование Символы Кондиция Минимальный Типичный Максимальный Единица
Напряжение питания логических схем VDD 1.65 3.0 3.3 V
Напряжение питания Display VCC 7.0 12.5 13.0 V
Вход высокого уровня VIH 0.8×VDD V
Вход низкого уровня VIL 0.2×VDD V
Выход высокого уровня VOH 0.9×VDD V
Выход низкого уровня VOL 0.1×VDD V
Display 50% Pixel on VCC =12.5V 16 45 mA

FPC Options:

Drawing FPC Length PIN Pitch ZIF FPC or HOTBAR FPC Интерфейс FPC No. Create Date
FPC2050002411XXXXX05_WEO012864AAAP3N00000 37.19 24 0.5 ZIF 6800/8080/4-SPI/I2C FPC2050002411XXXXX05 20160627
FPC2050003011XXXXX32_WEO012864A 51.05 30 0.5 ZIF 6800/8080/4-SPI/I2C FPC2050003011XXXXX32 20190926
 

Search keyword: 128x64 oled, oled 128x64, 1.54 oled, 1.54" oled, 1.54 дюйма oled, oled 1.54, oled 1.54"

go top
close