1,54 SPI OLED-Anzeige128x64
Modellnummer WEO012864A
►Typ: Grafik
►Bauweise: COG
►Größe: 1,54 Zoll OLED
►128 x 64 Punktmatrix
►IC：SSD1309
►3-V-Stromversorgung
►1/64 duty
►Schnittstelle: 6800,8080,I2C,SPI OLED-Anzeige
►die Farbe des Displays: Weiß / Gelb / Grün
►Andere in der nachstehenden Tabelle verfügbare FPC-Optionen
Beschreibung
Das Winstar 1,54 Zoll OLED Display WEO012864A hat eine Auflösung von 128x64 Pixeln. Dieses grafische Display hat eine Modulgröße von 42,04 x 27,22 mm und eine AA-Größe von 35,05 x 17,51 mm. Es ist mit SSD1309 Controller IC ausgestattet und unterstützt 6800/8080 8-Bit parallel, I2C- und 4-Draht-Seriell-Schnittstelle. Das Module ist in weiß, Gelb oder Amber erhältlich. Wenn Sie andere Emissionsfarben benötigen, kontaktieren Sie uns bitte.
Das WEO012864A ist eine COG(Chip-on-Glass) Modul, das sehr leicht und ultradünn (nur 1,41 mm) ist und geringer Stromverbrauch benötigt. Es ist geeignet für für Messgeräte, Heimanwendungen, Cloud / IoT-Systeme, Handgeräte, intelligente Technologiegeräte, Energiesysteme, Automobil, Kommunikationssysteme, medizinische Instrumente, tragbare Geräte, etc. Das Modul kann bei Temperaturen von -40 ℃ bis + 80 ℃ betrieben werden; die Lagertemperatur liegt zwischen -40 ° C und + 85 ° C.
FPC-Optionen
Zeichnung
Data source ref:WEO012864ALAP3N00000
Technische Daten
Schnittstelle Pin-Funktion
| No. | Symbol | Beschreibung | |||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 1 | NC(GND) | No connection | |||||||||||||||
| 2 | VLSS | This is an analog ground pin | |||||||||||||||
| 3 | VSS | Ground. | |||||||||||||||
| 4 | NC | No connection | |||||||||||||||
| 5 | VDD | Power supply pin for core logic operation | |||||||||||||||
| 6 | BS1 | MCU bus interface selection pins. Select appropriate logic setting as described in the following table. BS2 and BS1 are pin select
Note (1) 0 is connected to VSS (2) 1 is connected to VDD |
|||||||||||||||
| 7 | BS2 | ||||||||||||||||
| 8 | CS# | This pin is the chip select input connecting to the MCU. The chip is enabled for MCU communication only when CS# is pulled LOW (active LOW). |
|||||||||||||||
| 9 | RES# | This pin is reset signal input. When the pin is pulled LOW, initialization of the chip is executed. Keep this pin pull HIGH during normal operation. |
|||||||||||||||
| 10 | D/C# | This pin is Data/Command control pin connecting to the MCU. When the pin is pulled HIGH, the data at D[7:0] will be interpreted as data. When the pin is pulled LOW, the data at D[7:0] will be transferred to a command register. In I2C mode, this pin acts as SA0 for slave address selection. |
|||||||||||||||
| 11 | R/W# | This pin is read / write control input pin connecting to the MCU interface. When 6800 interface mode is selected, this pin will be used as Read/Write (R/W#) selection input. Read mode will be carried out when this pin is pulled HIGH and write mode when LOW. When 8080 interface mode is selected, this pin will be the Write (WR#) input. Data write operation is initiated when this pin is pulled LOW and the chip is selected. When serial or I2C interface is selected, this pin must be connected to VSS. |
|||||||||||||||
| 12 | E/RD# | This pin is MCU interface input. When 6800 interface mode is selected, this pin will be used as the Enable (E) signal. Read/write operation is initiated when this pin is pulled HIGH and the chip is selected. When 8080 interface mode is selected, this pin receives the Read (RD#) signal. Read operation is initiated when this pin is pulled LOW and the chip is selected. When serial or I2C interface is selected, this pin must be connected to VSS. |
|||||||||||||||
| 13-20 | D0~D7 | These pins are bi-directional data bus connecting to the MCU data bus. Unused pins are recommended to tie LOW. When serial interface mode is selected, D0 will be the serial clock input: SCLK; D1 will be the serial data input: SDIN and D2 should be kept NC. When I2C mode is selected, D2, D1 should be tied together and serve as SDAout, SDAin in application and D0 is the serial clock input, SCL. |
|||||||||||||||
| 21 | IREF | This pin is the segment output current reference pin. IREF is supplied externally. |
|||||||||||||||
| 22 | VCOMH | COM signal deselected voltage level. A capacitor should be connected between this pin and VSS. |
|||||||||||||||
| 23 | VCC | Power supply for panel driving voltage. This is also the most positive power voltage supply pin. | |||||||||||||||
| 24 | NC(GND) | No connection |
mechanische Daten
| Artikel | Ausmaß | Einheit |
|---|---|---|
| Punktmatrix | 128 x 64 | dots |
| Abmaße der modul | 42,04 × 27,22 × 1,41 | mm |
| Aktiver Bereich | 35,05 × 17,51 | mm |
| Punktgröße | 0,249 × 0,249 | mm |
| Punktabstand | 0,274 × 0,274 | mm |
| Display Mode | Passive Matrix | |
| Display Color | Monochrome | |
| Drive Duty | 1/64 Duty | |
| IC | SSD1309 | |
| Schnittstelle | 6800/8080/4-Wire SPI/I2C | |
| Größe (Diagonale) | 1.54 Zoll | |
Absolute Grenzwerte
| Parameter | Symbol | Mindestwert | Maximalwert | Einheit |
|---|---|---|---|---|
| Supply Voltage for Logic | VDD | -0,3 | 4 | V |
| Supply Voltage for Display | VCC | 0 | 17 | V |
| Betriebstemperatur | TOP | -40 | +80 | °C |
| Lagertemperatur | TSTG | -40 | +85 | °C |
elektronische Eingenschaften
| Artikel | Symbol | Bedingung | Mindestwert | typischer Wert | Maximalwert | Einheit |
|---|---|---|---|---|---|---|
| Supply Voltage for Logic | VDD | － | 1,65 | 3,0 | 3,3 | V |
| Supply Voltage for Display | VCC | － | 7,0 | 12,5 | 13,0 | V |
| High Level Input | VIH | － | 0,8×VDD | － | － | V |
| Low Level Input | VIL | － | － | － | 0,2×VDD | V |
| High Level Output | VOH | － | 0,9×VDD | － | － | V |
| Low Level Output | VOL | － | － | － | 0,1×VDD | V |
| Display 50% Pixel on | VCC =12,5V | － | 16 | 45 | mA | |
FPC-Optionen:
| Bild | FPC Length | PIN | Pitch | ZIF FPC or HOTBAR FPC | Schnittstelle | FPC No. | Create Date |
|---|---|---|---|---|---|---|---|
 |
37.19 | 24 | 0.5 | ZIF | 6800/8080/4-SPI/I2C | FPC2050002411XXXXX05 | 20160627 |
 |
51.05 | 30 | 0.5 | ZIF | 6800/8080/4-SPI/I2C | FPC2050003011XXXXX32 | 20190926 |
