1.5 Zoll 128x128 COG OLED-Anzeige
Modellnummer WEO128128H
►Typ: Grafik
►Bauweise: COG
►Größe: 1,5 Zoll OLED
►128 x 128 Punktmatrix
►IC:CH1120
►3-V-Stromversorgung
►1/128 duty
►Schnittstelle: 8080,SPI,I2C
►die Farbe des Displays: Weiß / Gelb
►Unterstützt Grauskala
Beschreibung
Zeichnung
Data source ref:WEO128128HLAP3N00000
Technische Daten
Schnittstelle Pin-Funktion
No. | Symbol | Beschreibung | |||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
1 | ESD_GND | This pin should be connected to GND. | |||||||||||||||
2 | VPP | This is the most positive voltage supply pin of the chip. It should be supplied externally. |
|||||||||||||||
3 | VCOMH | This is a pin for the voltage output high level for common signals. A capacitor should be connected between this pin and GND. |
|||||||||||||||
4 | VDD | Power supply for logic | |||||||||||||||
5 | NC | No connection | |||||||||||||||
6 | IM1 | These are the MPU interface mode select pins.
|
|||||||||||||||
7 | IM2 | ||||||||||||||||
8 | VSS | Ground for logic and analog. This pin should be connected to GND externally. | |||||||||||||||
9 | IREF | This is a segment current reference pin. A resistor should be connected between this pin and GND. |
|||||||||||||||
10 | CSB | This pin is the chip select input. When CSB = “L”, then the chip select becomes active, and data/command I/O is enabled. When in I2C interface, this pin is not used, so it must be connected to “L”. |
|||||||||||||||
11 | RESB | This is a reset signal input pin. When RESB is set to “L”, the settings are initialized. The reset operation is performed by the RESB signal level. This pin internal pull high. | |||||||||||||||
12 | A0 | This is the Data/Command control pin that determines whether the data bits are data or a command. A0 = “H”: the inputs at D0 to D7 are treated as display data A0 = “L”: the inputs at D0 to D7 are transferred to the command registers. In I2C interface, this pin serves as SA0 to distinguish the different address of OLED driver. When in 3-wire interface, this pin is not used, so it must be connected to “L”. |
|||||||||||||||
13 | WRB | This is a MPU interface input pin. When connected to an 8080 MPU, this is active LOW. This pin connects to the 8080 MPU WR signal. The signals on the data bus are latched at the rising edge of the WR signal When in 3-wire.4-wire & I2C interface, this pin is not used, so it must be connected to “L”. |
|||||||||||||||
14 | RDB | This is a MPU interface input pin. When connected to an 8080 series MPU, it is active LOW. This pin is connected to the RD signal of the 8080 series MPU, and the data bus is in an output status when this signal is “L”. When in 3-wire.4-wire & I2C interface, this pin is not used, so it must be connected to “L”. |
|||||||||||||||
15 | D0 | This is an 8-bit bi-directional data bus that connects to an 8-bit or 16-bit standard MPU data bus. When the serial interface(SPI) and I2C is selected, then D0 serves as the serial clock input pin (SCL) and D1 serves as the serial data input pin (SI). At this time, D2 to D7 are set to high impedance. D7~D2 is recommended to connect the VDD or GND. It is also allowed to leave D7~D2 unconnected. |
|||||||||||||||
16 | D1 | ||||||||||||||||
17 | D2 | ||||||||||||||||
18 | D3 | ||||||||||||||||
19 | D4 | ||||||||||||||||
20 | D5 | ||||||||||||||||
21 | D6 | ||||||||||||||||
22 | D7 | ||||||||||||||||
23 | VPP | This is the most positive voltage supply pin of the chip It should be supplied externally. |
|||||||||||||||
24 | ESD_GND | This pin should be connected to GND. |
mechanische Daten
Artikel | Ausmaß | Einheit |
---|---|---|
Punktmatrix | 128 × 128 | dots |
Abmaße der modul | 33.80 x 36.50 x 2.01 | mm |
Aktiver Bereich | 26.86 x 26.86 | mm |
Punktgröße | 0.185 x 0.185 | mm |
Punktabstand | 0.210 x 0.210 | mm |
Display Mode | Passive Matrix | |
Display Color | Monochrome | |
Drive Duty | 1/128 Duty | |
Graustufen | 4 bits | |
IC | CH1120 | |
Schnittstelle | 8080,SPI,I2C | |
Größe (Diagonale) | 1.5 inch |
Absolute Grenzwerte
Parameter | Symbol | Mindestwert | Maximalwert | Einheit |
---|---|---|---|---|
Supply Voltage for Logic | VDD | -0.3 | 3.5 | V |
Supply Voltage for Display | VPP | -0.3 | 15.0 | V |
Betriebstemperatur | TOP | -40 | +80 | °C |
Lagertemperatur | TSTG | -40 | +85 | °C |
elektronische Eingenschaften
Artikel | Symbol | Bedingung | Mindestwert | typischer Wert | Maximalwert | Einheit |
---|---|---|---|---|---|---|
Supply Voltage for Logic | VDD | - | 1.65 | 3.0 | 3.3 | V |
Supply Voltage for Display | VPP | - | 8.0 | 14.5 | 15.0 | V |
Input High Volt. | VIH | - | 0.8×VDD | - | VDD | V |
Input Low Volt. | VIL | - | GND | - | 0.2×VDD | V |
Output High Volt. | VOH | - | 0.8×VDD | - | VDD | V |
Output Low Volt. | VOL | - | GND | - | 0.1×VDD | V |
Display 50% Pixel on | IPP | VPP=14.5V | - | 20 | 30 | mA |